Toyota Tundra (2015 year). Manual — part 1016
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
2 (SCC) - Case GND
Always
1.62 to 1.78 Ω
Text in Illustration
*a
Component without harness connected
(Solenoid Coil Sub-assembly)
*b
Case GND
HINT:
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002HO901GX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WF1AM TRANSFER: TRANSFER ASSEMBLY: REASSEMBLY; 2015 MY Tundra [08/2014 - ]
REASSEMBLY
HINT:
1. INSTALL TRANSFER CASE OIL SEAL
(a) Using SST and a hammer, tap in a new transfer case oil seal as
shown in the illustration.
SST: 09950-60010
09951-00630
SST: 09950-70010
09951-07100
Drive in depth (A):
1.4 to 2.4 mm (0.056 to 0.094 in.)
NOTICE:
Be careful not to damage or deform the transfer case oil seal.
2. INSTALL TRANSFER DRIVEN SPROCKET BEARING (FRONT)
(a) Using SST and a press, press in a new transfer driven sprocket
bearing (front) as shown in the illustration.
SST: 09950-60010
09951-00390
09952-06010
SST: 09950-60020
09951-00910
SST: 09950-70010
09951-07100
NOTICE:
The transfer driven sprocket bearing (front) should be installed
completely.
3. INSTALL NO. 2 TRANSFER CASE OIL SEAL
WF1AM TRANSFER: TRANSFER ASSEMBLY: REASSEMBLY; 20...
(a) Using SST and a press, press in a new No. 2 transfer case oil
seal as shown in the illustration.
SST: 09316-12010
SST: 09513-36040
Drive in depth (A):
1.5 to 2.5 mm (0.060 to 0.098 in.)
NOTICE:
Be careful not to damage or deform the No. 2 transfer case oil
seal.
4. INSTALL OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (FRONT)
(a) Install the output shaft companion flange sub-assembly (front).
(b) Using a snap ring expander, install the shaft snap ring.
5. INSTALL TRANSFER OIL SEPARATOR
(a) Using a T25 ''TORX'' socket wrench, install the bolt and transfer
oil separator.
Torque:
7.6 N·m {77 kgf·cm, 67in·lbf}
6. INSPECT TRANSFER LOWER PLANETARY RING GEAR
(a) Install the transfer lower planetary ring gear.
(b) Using a screwdriver, install the transfer lower planetary ring gear hole snap ring.
Text in Illustration
WF1AM TRANSFER: TRANSFER ASSEMBLY: REASSEMBLY; 20...
*a
Protective Tape
HINT:
Tape the screwdriver tip before use.
7. INSTALL TRANSFER LOWER PLANETARY GEAR ASSEMBLY
(a) Using SST and a press, press in a new transfer input gear radial
ball bearing.
SST: 09214-76011
NOTICE:
The transfer input gear radial ball bearing should be installed
completely.
(b) Install the transfer lower planetary gear assembly.
8. INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE
(a) Install the transfer lower planetary gear bearing, the No. 2
transfer output shaft spacer and the transfer high and low clutch
sleeve.
Text in Illustration
*1
Transfer High and Low Clutch Sleeve
*2
No. 2 Transfer Output Shaft Spacer
*3
Transfer Lower Planetary Gear Bearing
*a
Transfer Lower Planetary Gear Assembly Side
NOTICE:
Make sure that the transfer lower planetary gear bearing is
installed facing the correct direction.
9. INSTALL REAR TRANSFER OUTPUT SHAFT
WF1AM TRANSFER: TRANSFER ASSEMBLY: REASSEMBLY; 20...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст