Toyota Tundra (2015 year). Manual — part 1015
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002HO701BX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: WF1AM TRANSFER: TRANSFER ASSEMBLY: INSPECTION; 2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (FRONT)
Minimum Diameter:
JOURNAL
SPECIFIED CONDITION
A
34.962 mm (1.376 in.)
B
39.955 mm (1.573 in.)
If the outer diameter is less than the minimum, replace the
output shaft companion flange sub-assembly (front).
2. INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY
Maximum clearance:
0.93 mm (0.037 in.)
If the clearance is more than the maximum, replace the transfer
low planetary gear assembly.
Maximum clearance:
0.021 mm (0.0008 in.)
If the clearance is more than the maximum, replace the transfer
low planetary gear assembly.
3. INSPECT REAR TRANSFER OUTPUT SHAFT
WF1AM TRANSFER: TRANSFER ASSEMBLY: INSPECTION; 201...
Minimum Diameter:
JOURNAL
SPECIFIED CONDITION
A
29.987 mm (1.181 in.)
B
34.848 mm (1.372 in.)
C
58.000 mm (2.284 in.)
D
49.110 mm (1.934 in.)
E
44.874 mm (1.767 in.)
If the diameter is less than the minimum, replace the rear
transfer output shaft.
4. INSPECT SOLENOID LOCK PLATE AND NO. 2 TRANSFER GEAR SHIFT FORK CLEARANCE
Standard thickness (A):
6.90 to 7.06 mm (0.272 to 0.277 in.)
7.16 to 7.32 mm (0.282 to 0.288 in.)
(c) Calculate the clearance between the solenoid lock plate and No. 2 transfer gear shift fork claw.
Maximum clearance (B) - (A):
0.42 mm (0.017 in.)
If the clearance is more than the maximum, replace the solenoid lock plate or No. 2 transfer gear shift
fork.
5. INSPECT NO. 1 TRANSFER GEAR SHIFT FORK AND NO. 2 TRANSFER GEAR SHIFT FORK
(a) Check the gear shift fork pad for wear or damage.
If necessary, replace the gear shift fork pad.
WF1AM TRANSFER: TRANSFER ASSEMBLY: INSPECTION; 201...
Minimum Diameter:
DIAMETER
SPECIFIED CONDITION
A
12.586 mm (0.496 in.)
B
12.586 mm (0.496 in.)
Text in Illustration
*1
No. 1 Transfer Gear Shift Fork
*2
No. 2 Transfer Gear Shift Fork
If the diameter is less than the minimum, replace the No. 1
transfer gear shift fork or No. 2 transfer gear shift fork.
6. INSPECT TRANSFER HIGH AND LOW CLUTCH SLEEVE
Minimum thickness:
3.00 mm (0.1182 in.)
If the thickness is less than the minimum, replace the transfer
high and low clutch sleeve.
7. INSPECT TRANSFER OUTPUT SHAFT SPACER
spacer.
Minimum Thickness:
TRANSFER OUTPUT SHAFT SPACER
MINIMUM THICKNESS
No. 1 Transfer Output Shaft Spacer
2.80 mm (0.111 in.)
No. 2 Transfer Output Shaft Spacer
4.045 mm (0.160 in.)
If the thickness is less than the minimum, replace the transfer
output shaft spacer.
8. INSPECT SOLENOID COIL SUB-ASSEMBLY
WF1AM TRANSFER: TRANSFER ASSEMBLY: INSPECTION; 201...
(a) Install the solenoid coil sub-assembly with the 3 nuts.
Torque:
9.5 N·m {97 kgf·cm, 84in·lbf}
Text in Illustration
*a
Rear Transfer Case Hole
Make sure that the solenoid coil sub-assembly terminal extends
out from the rear transfer case hole.
(b) Connect the solenoid coil sub-assembly terminal.
(1) Attach the claw to connect the solenoid coil sub-assembly
terminal.
(2) Install the retainer to the coupler.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
WF1AM TRANSFER: TRANSFER ASSEMBLY: INSPECTION; 201...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст