Toyota Tundra (2015 year). Manual — part 2085
NEXT
NEXT
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000002WKL01PX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: LIGHTING: LIGHTING SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING; 2015 MY Tundra [08/2014
- ]
HOW TO PROCEED WITH TROUBLESHOOTING
HINT:
Use these procedures to troubleshoot the lighting system.
*: Use the Techstream.
1.
VEHICLE BROUGHT TO WORKSHOP
2.
INSPECT BATTERY VOLTAGE
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
3.
CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Result
RESULT
PROCEED TO
CAN DTC is not output
A
CAN DTC is output
B
B
GO TO CAN COMMUNICATION SYSTEM
LIGHTING: LIGHTING SYSTEM: HOW TO PROCEED WITH TR...
A
A
A
4.
CHECK FOR DTC*
(a) Clear the DTC
.
(b) Recheck for DTC
.
Result
RESULT
PROCEED TO
DTC is not output
A
DTC is output
B
B
GO TO DIAGNOSTIC TROUBLE CODE CHART
5.
PROBLEM SYMPTOMS TABLE
Result
RESULT
PROCEED TO
Fault is not listed in problem symptoms table
A
Fault is listed in problem symptoms table
B
B
Go to step 7
6.
OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) Operation Check
.
.
LIGHTING: LIGHTING SYSTEM: HOW TO PROCEED WITH TR...
NEXT
NEXT
(c) DATA LIST / ACTIVE TEST
.
7.
ADJUST, REPAIR OR REPLACE
8.
CONFIRMATION TEST
NEXT
END
LIGHTING: LIGHTING SYSTEM: HOW TO PROCEED WITH TR...
Last Modified: 9-16-2014
6.6 D
Doc ID: RM000002WL3045X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: LIGHTING: LIGHTING SYSTEM: OPERATION CHECK; 2015 MY Tundra [08/2014 - ]
OPERATION CHECK
1. CHECK ILLUMINATED ENTRY SYSTEM OPERATION
(a) The illuminated entry system controls the following lights:
Transponder key light
Foot light
(b) Check the illuminated entry system with the ignition switch OFF.
Leave the doors unlocked for 15 seconds.
Turn the ignition switch ACC or ON.
Lock all the doors.
(c) Check the illuminated entry system with the ignition switch ACC or ON.
(1) Check that the lights stay lit after turning the ignition switch OFF with all the doors closed and the
ignition switch ACC or ON. Then check that the lights fade out under the following conditions:
Leave the doors unlocked for 15 seconds.
Turn the ignition switch ACC or ON.
Lock all the doors.
2. CHECK BATTERY SAVER OPERATION
(a) Basic function inspection
(1) Turn the ignition switch OFF and close all the doors.
(2) Open the driver side door to turn the room light on, and leave the door open. Check that the light turns
off after about 20 minutes.
(3) After the room light turns off, close the driver's door.
(4) Open any door to turn the room light on, and then open another door. Check that the room light turns
off within 20 minutes after opening the doors.
(b) Interior light auto cut function inspection
3. CHECK LIGHT AUTO TURN OFF OPERATION
LIGHTING: LIGHTING SYSTEM: OPERATION CHECK; 2015 MY ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст