Toyota Tundra (2015 year). Manual — part 578
OK
Engine and ECT:
TESTER
DISPLAY
MEASUREMENT
ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
SPD (NT)
Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up is:
ON (after warming up engine): Input
turbine speed (NT) is equal to engine
speed
OFF (idling with shift lever on N): Input
turbine speed (NT) is nearly equal to
engine speed
Data is displayed in
SPD (NT) is always 0 while driving:
Open or short in the sensor or circuit.
SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or
more:
Sensor trouble, improper installation, or intermittent connection trouble in the circuit.
PROCEDURE
1.
INSPECT SPEED SENSOR NT INSTALLATION
(a) Check the speed sensor NT installation.
OK:
The installation bolt is tightened properly and there is no
clearance between the sensor and transmission case.
NG
SECURELY INSTALL OR REPLACE SPEED SENSOR
NT
2.
INSPECT SPEED SENSOR NT
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
OK
(a) Disconnect the D65 speed sensor connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
1 - 2
20°C (68°F)
560 to 680 Ω
NG
REPLACE SPEED SENSOR NT
3.
CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)
(a) Disconnect the D74 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
D74-124 (NT+) - D74-123 (NT-)
20°C (68°F)
560 to 680 Ω
D74-124 (NT+) - Body ground
Always
10 kΩ or higher
D74-123 (NT-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE ECM
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM0000012TD090X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0722; Output Speed Sensor
Circuit No Signal; 2015 MY Tundra [08/2014 - ]
DTC
P0722
Output Speed Sensor Circuit No Signal
DESCRIPTION
SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the
ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.
The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed
sensor and the throttle position sensor signal.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0722
All conditions below are detected 5 seconds or more
continuously (2-trip detection logic)
(a) No signal from speed sensor SP2 is input to ECM
(b) Vehicle speed is 9 km/h (5.59 mph) or more
(c) Park/neutral position switch is OFF
Open or short in speed sensor SP2
circuit
Speed sensor SP2
ECM
Automatic transmission (clutch,
brake or gear, etc.)
Reference: Inspect using an oscilloscope.
TERMINAL NO. (SYMBOL)
TOOL SETTING
CONDITION
SPECIFIED
CONDITION
D74-101 (SP2+) - D74-100
(SP2-)
2 V/DIV., 20
msec./DIV
Vehicle speed 20 km/h (12
mph)
Refer to the
illustration
MONITOR DESCRIPTION
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст