Toyota Tundra (2015 year). Manual — part 1741
(c) Align the No. 2 chain's mark plates (yellow) with the timing
shown in the illustration.
NOTICE:
The camshaft timing exhaust gear has 2 grooves. Align the
The crankshaft timing gear and camshaft exhaust gear will be
installed with the No. 1 and No. 2 chains connected to the
gears.
(d) Install the crankshaft timing sprocket to the crankshaft.
27. INSTALL NO. 1 CHAIN VIBRATION DAMPER RH
(a) Install the vibration damper with the 2 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
28. INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH
HINT:
If you cannot install the chain tensioner slipper due to the
(a) Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
(c) Install the chain tensioner with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
(d) Remove the hexagon wrench from the chain tensioner.
30. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
(a) Install the chain tensioner with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
(b) While pushing down the No. 2 chain tensioner, insert a pin of
φ1.0 mm (0.0394 in.) into the hole to fix it in place.
31. INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH
(a) Align the No. 1 chain's orange mark plate with the camshaft timing gear's timing mark, and attach the
chain to the gear as shown in the illustration.
(b) Align the No. 1 chain's orange mark plate with the crankshaft
timing gear's timing mark, and attach the chain to the gear
as shown in the illustration.
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
(c) Align the No. 2 chain's mark plates (yellow) with the timing
shown in the illustration.
NOTICE:
The camshaft timing exhaust gear has 2 grooves. Align the
The crankshaft timing gear and camshaft exhaust gear will be
installed with the No. 1 and No. 2 chains connected to the
gears.
(d) Install the crankshaft timing sprocket to the crankshaft.
(g) Remove the pin from the No. 2 chain tensioner.
32. INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH
HINT:
If you cannot install the chain tensioner slipper due to the
(a) Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
(c) Install a new gasket and the chain tensioner with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
34. INSTALL NO. 1 CHAIN VIBRATION DAMPER LH
(a) Install the vibration damper with the 2 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
(b) Remove the hexagon wrench from the No. 1 chain tensioner.
35. TIGHTEN CAMSHAFT TIMING GEAR
(a) LH:
Torque:
100 N·m {1020 kgf·cm, 74ft·lbf}
the bolt.
Torque:
100 N·m {1020 kgf·cm, 74ft·lbf}
3UR-FBE ENGINE MECHANICAL: ENGINE UNIT: REASSEMBLY;...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст