Toyota Tundra (2015 year). Manual — part 1867
DTC
COMPONENT
FAIL-SAFE OPERATION
FAIL-SAFE
DEACTIVATION
CONDITION
- All cylinder fuel cut or
malfunction cylinder fuel cut
P0327, P0328, P0332
and P0333
Knock Sensor
ECM sets ignition timing to maximum
retard.
Ignition switch off
P0351 to P0358
Igniter
ECM cuts fuel.
Pass condition
detected
P0504
Stop Light Switch
The accelerator pedal opening angle is
fixed when there is an accelerator pedal
angle is fixed
P2120, P2121, P2122,
P2123, P2125, P2127,
P2128 and P2138
Accelerator Pedal
Position (APP) Sensor
The APP sensor has 2 sensor circuits:
Main and Sub.
If either circuit malfunctions, the ECM
limits the engine output.
If both circuits malfunction, the ECM
regards the accelerator pedal as being
released. As a result, the throttle valve
is closed and the engine idles.
Pass condition
detected and then
ignition switch
turned off
P2432, P2433, P2437
and P2438
Secondary Air
Injection System
Throttle valve opening angle control is
performed
Pass condition
detected
P2440 and P2442
Secondary Air
Injection System
Throttle valve opening angle control is
performed
Pass condition
detected
P2445 and P2447
Secondary Air
Injection System
Throttle valve opening angle control is
performed
Pass condition
detected
HINT:
*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the
accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
*2: Misfire related fail-safe operations occur when catalyst overheat malfunctions occur.
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: FAIL-SAFE ...
Last Modified: 9-16-2014
6.6 U
Doc ID: RM000000SXS0C5X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DATA LIST / ACTIVE TEST; 2015 MY Tundra [08/2014
- ]
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend
solely on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine and ECT / Data List.
(g) According to the display on the Techstream, use the Data List.
TESTER
DISPLAY
MEASUREMENT
ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0
mph), Max.: 255
km/h (158 mph)
Actual vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed/
Min.: 0 rpm,
Max.: 16383 rpm
650 to 750 rpm: Idling
-
Calculate Load
Calculated load by
ECM/
Min.: 0%, Max.:
100%
11 to 25%:
Idling
12 to 26%:
Running without
load (2500 rpm)
-
Vehicle Load
Vehicle load/
Min.: 0%, Max.:
25700%
Actual vehicle load
-
MAF
Air flow rate from
Mass Air Flow
(MAF) meter/
Min.: 0 gm/sec
Max.: 655.35
gm/sec
4.0 to 8.0 gm/sec: Idling
If the value approximately 0.0 gm/sec:
Mass air flow meter power
source circuit open.
VG circuit open or short.
If the value 160.0 gm/sec or more:
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DATA LIST /...
TESTER
DISPLAY
MEASUREMENT
ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
E2G circuit open.
Atmosphere
Pressure
Atmospheric
pressure/
Min.: 0 kPa (0
mmHg), Max.:
255 kPa (1912.6
mmHg)
Equivalent to atmospheric
pressure (absolute
pressure)
-
Coolant Temp
Engine coolant
temperature/
Min.: -40°C
(-40°F), Max.:
140°C (284°F)
75 to 100°C (167 to
212°F): After warming up
If the value -40°C (-40°F): sensor circuit
open.
If the value 140°C (284°F): sensor circuit
shorted.
Intake Air
Intake air
temperature/
Min.: -40°C
(-40°F), Max.:
140°C (284°F)
Equivalent to ambient air
temperature
If the value -40°C (-40°F): sensor circuit
open.
If the value 140°C (284°F): sensor circuit
shorted.
Engine Run
Time
Engine run time/
Min.: 0 s, Max.:
65535 s
Time after engine start
Service data
Initial Engine
Coolant Temp
Initial engine
coolant
temperature/
Min.: -40°C
(-40°F), Max.:
119.3°C (246.7°F)
Close to ambient air
temperature
Service data
Initial Intake Air
Temp
Initial intake air
temperature/
Min.: -40°C
(-40°F), Max.:
119.3°C (246.7°F)
Close to ambient air
temperature
Service data
Battery Voltage
Battery voltage/
Min.: 0 V, Max.:
65.535 V
11 to 14 V: Idling
-
Accelerator
Position
Accelerator pedal
position/
Min.: 0%, Max.:
399.9%
Actual accelerator pedal
position
-
Accel Sens. No.1
Volt %
Absolute
Accelerator Pedal
Position (APP) No.
1/
Min.: 0%, Max.:
100%
10 to 22%: accelerator
pedal is released
52 to 90%: accelerator
pedal is fully depressed
-
Accel Sens. No.2
Volt %
Absolute APP No.
2/
Min.: 0%, Max.:
100%
24 to 40%: accelerator
pedal is released
68 to 95%: accelerator
pedal is fully depressed
-
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DATA LIST /...
TESTER
DISPLAY
MEASUREMENT
ITEM/RANGE
NORMAL CONDITION
DIAGNOSTIC NOTE
Accel Sensor
Out No. 1
Accelerator pedal
position sensor
No. 1 voltage/
Min.: 0 V, Max.:
4.980 V
0.5 to 1.1 V: accelerator
pedal is released
2.6 to 4.5 V: accelerator
pedal is fully depressed
-
Accel Sensor
Out No. 2
Accelerator pedal
position sensor
No. 2 voltage/
Min.: 0 V, Max.:
4.980 V
1.2 to 2.0 V: accelerator
pedal is released
3.4 to 4.75 V: accelerator
pedal is fully depressed
-
Accelerator Idle
Position
Whether or not
accelerator pedal
position sensor
detecting idle/
ON or OFF
ON: Idling
-
Accel Fully Close
Learn #1
Accelerator fully
closed learning
value No. 1/
Min.: 0, Max.:
124.5 deg
-
ETCS service data
Accel Fully Close
Learn #2
Accelerator fully
closed learning
value No. 2/
Min.: 0, Max.:
124.5 deg
-
ETCS service data
Throttle Sensor
Volt %
Throttle valve
opening
percentage
according to
throttle position
sensor/
Min.: 0%, Max.:
100%
10 to 22%:
Accelerator
pedal released
64 to 96%:
Accelerator
pedal fully
depressed
Value calculated based on the voltage at
terminal VTA1
Throttl Sensor
#2 Volt %
Throttle valve
opening
percentage
according to
throttle position
sensor No. 2/
Min.: 0%, Max.:
100%
42 to 62%:
Accelerator
pedal released
92 to 100%:
Accelerator
pedal fully
depressed
Value calculated based on the voltage at
terminal VTA2
ST1
Brake pedal
signal/
ON or OFF
ON: Brake pedal
depressed
-
System Guard
System guard/
ON or OFF
-
ETCS service data
Open Side
Malfunction
Open side
malfunction/
ON or OFF
-
ETCS service data
3UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: DATA LIST /...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст