Toyota Tundra (2015 year). Manual — part 1165
OK
(a) Disconnect the VVT sensor (for exhaust side) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Bank 1
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
D40-3 (VC2) - Body ground
Ignition switch ON
4.5 to 5.0 V
Bank 2
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
D41-3 (VC2) - Body ground
Ignition switch ON
4.5 to 5.0 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
2.
CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P0367,...
OK
(a) Disconnect the VVT sensor (for exhaust side) connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
D40-1 (EX+) - D74-69 (EV1+)
Always
Below 1 Ω
D40-2 (EX-) - D74-68 (EV1-)
Always
Below 1 Ω
D41-1 (EX+) - D74-64 (EV2+)
Always
Below 1 Ω
D41-2 (EX-) - D74-65 (EV2-)
Always
Below 1 Ω
D40-1 (EX+) or D74-69 (EV1+) - Body ground
Always
10 kΩ or higher
D40-2 (EX-) or D74-68 (EV1-) - Body ground
Always
10 kΩ or higher
D41-1 (EX+) or D74-64 (EV2+) - Body ground
Always
10 kΩ or higher
D41-2 (EX-) or D74-65 (EV2-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P0367,...
OK
OK
OK
3.
CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE)
(a) Check the VVT sensor (for exhaust side) installation.
OK:
Sensor is installed correctly.
NG
SECURELY REINSTALL SENSOR
4.
INSPECT EXHAUST CAMSHAFT
Teeth do not have any cracks or deformation.
HINT:
Perform "Inspection After Repair" after replacing the exhaust camshaft
.
NG
REPLACE EXHAUST CAMSHAFT
5.
CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)
NG
ADJUST VALVE TIMING
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P0367,...
NEXT
6.
REPLACE VVT SENSOR (FOR EXHAUST SIDE)
(a) Replace the VVT sensor (for exhaust side)
.
7.
CHECK WHETHER DTC OUTPUT RECURS
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear DTCs
.
(e) Refer to the confirmation driving pattern.
(f) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
(g) Read DTCs.
Result
DISPLAY (DTC OUTPUT)
PROCEED TO
No DTC is output
A
P0365, P0367, P0368, P0390, P0392 or P0393 is output
B
HINT:
If the engine does not start, replace the ECM.
B
REPLACE ECM
A
END
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P0367,...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст