Toyota Tundra (2015 year). Manual — part 2341
ILLUSTRATION
DOOR LOCK: REAR DOOR LOCK (for Double Cab): COMPONENTS;...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002ZPZ00MX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: DOOR LOCK: REAR DOOR LOCK (for Double Cab): REMOVAL; 2015 MY Tundra [08/2014 - ]
REMOVAL
HINT:
Use the same procedures for the LH side and RH side.
The procedures listed below are for the LH side.
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the
battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice
before proceeding with work
.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH
4. REMOVE REAR UPPER DOOR ARMREST BASE PANEL LH
5. REMOVE REAR DOOR FRAME GARNISH LH
6. REMOVE REAR DOOR ARMREST COVER LH
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
8. REMOVE REAR NO. 2 DOOR TRIM BRACKET
9. REMOVE REAR DOOR SERVICE HOLE COVER LH
10. REMOVE REAR DOOR GLASS RUN LH
11. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH
12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
13. REMOVE REAR DOOR LOCK ASSEMBLY LH
14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
DOOR LOCK: REAR DOOR LOCK (for Double Cab): REMOVAL; 201...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM000002NGF01DX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: DOOR LOCK: REAR DOOR LOCK (for Double Cab): INSPECTION; 2015 MY Tundra [08/2014 - ]
INSPECTION
1. INSPECT REAR DOOR LOCK ASSEMBLY LH
(a) Check the door lock motor.
(1) Apply battery voltage to the door lock and check operation of
the door lock.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock
If the result is not as specified, replace the door lock
assembly.
(b) Check the door lock position switch.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
6 (LSSR) - 9 (E)
Unlock
Below 1 Ω
Lock
10 kΩ or higher
If the result is not as specified, replace the door lock assembly.
2. INSPECT REAR DOOR LOCK ASSEMBLY RH
(a) Check the door lock motor.
DOOR LOCK: REAR DOOR LOCK (for Double Cab): INSPECTION; 2...
(1) Apply battery voltage to the door lock and check operation of
the door lock.
OK:
MEASUREMENT CONDITION
SPECIFIED CONDITION
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock
If the result is not as specified, replace the door lock
assembly.
(b) Check the door lock position switch.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
6 (LSSR) - 9 (E)
Unlock
Below 1 Ω
Lock
10 kΩ or higher
If the result is not as specified, replace the door lock assembly.
DOOR LOCK: REAR DOOR LOCK (for Double Cab): INSPECTION; 2...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст