Toyota Tundra (2015 year). Manual — part 512
Last Modified: 9-16-2014
6.6 N
Doc ID: RM000002YBC02CX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (for Floor Shift Type): ADJUSTMENT; 2015
MY Tundra [08/2014 - ]
ADJUSTMENT
1. INSPECT SHIFT LEVER POSITION
(a) When moving the shift lever from N to other positions, check that the lever can be moved smoothly and
accurately to each position and that the position indicator comes on in accordance with the shift lever
position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
2. ADJUST SHIFT LEVER POSITION
(a) Move the shift lever to N.
(b) Fold back the transmission control cable adjust case cover. Then
while sliding the slider toward the cable end side, press out the
lock piece from the back side to release the lock.
Text in Illustration
*1
Lock Piece
*2
Slider
set the lock.
Text in Illustration
*1
Lock Piece
*2
Slider
NOTICE:
(e) Inspect the shift lever operation after the adjustment.
A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002YBH03VX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (for Floor Shift Type): REASSEMBLY; 2015
MY Tundra [08/2014 - ]
REASSEMBLY
1. INSTALL SHIFT LOCK CONTROL ECU
(a) Attach the 3 claws to install the shift lock control ECU to the shift lever assembly.
(b) Connect the shift lock solenoid connector.
2. INSTALL POSITION INDICATOR LED
(a) Attach the claw to install the position indicator LED to the lower position indicator housing.
3. INSTALL INDICATOR LIGHT WIRE SUB-ASSEMBLY
(a) Connect the connector and install the indicator light wire sub-assembly to the lower position indicator
housing.
4. INSTALL LOWER POSITION INDICATOR HOUSING
(a) Attach the 4 claws to install the lower position indicator housing
to the shift lever assembly.
5. CONNECT INDICATOR LIGHT WIRE SUB-ASSEMBLY
(a) Attach the 4 guides.
A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (...
(b) Securely connect the 2 wire terminals to terminals 4 (ILL+) and
Text in Illustration
*1
Connector Housing Retainer
*a
Component without harness connected
(Transmission Control Switch)
6. INSTALL NO. 2 POSITION INDICATOR SLIDE COVER
(a) Install the No. 2 position indicator slide cover to the position indicator slide cover.
7. INSTALL POSITION INDICATOR SLIDE COVER
(a) Install the position indicator slide cover with the No. 2 position indicator slide cover to the shift lever
assembly.
HINT:
Install the position indicator slide cover so that its mark faces the vehicle front.
8. INSTALL UPPER POSITION INDICATOR HOUSING
(a) Attach the 4 claws to install the upper position indicator housing to the shift lever assembly.
9. INSTALL SHIFT LEVER CAP
(a) Attach the 2 claws to install the shift lever cap to the shift lever
assembly.
A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002YBD04AX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (for Floor Shift Type): INSTALLATION;
2015 MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
(a) Temporarily install the transmission floor shift assembly to the body with the 4 bolts.
(b) Fully tighten the 4 bolts in the order shown in the illustration.
Torque:
14 N·m {143 kgf·cm, 10ft·lbf}
(c) Connect the clamp and 2 connectors.
(e) Connect the control cable end to the shift lever assembly.
Text in Illustration
*1
Ridged
NOTICE:
Make sure to install the cable end so that the inner cable is not
2. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Air Duct)
(a) Install the No. 1 console box duct with the 2 clips.
3. ADJUST SHIFT LEVER POSITION
4. INSPECT SHIFT LEVER POSITION
5. INSTALL CONSOLE BOX ASSEMBLY
A760F AUTOMATIC TRANSMISSION: SHIFT LEVER ASSEMBLY (...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст