Toyota Tundra (2015 year). Manual — part 2626
(a) Slide the clamp and disconnect the No. 2 water by-pass hose
from the front water by-pass joint.
(b) Remove the 4 nuts, front water by-pass joint and 2 gaskets.
29. REMOVE NO. 2 ENGINE COVER
30. REMOVE NO. 1 ENGINE COVER
31. REMOVE AIR TUBE SUB-ASSEMBLY
(a) Remove the bolt, disconnect the 2 hoses, and remove the air
tube sub-assembly.
32. REMOVE WATER INLET HOUSING
(a) Remove the 3 bolts, water inlet housing and gasket.
33. REMOVE WATER PUMP PULLEY
(a) Using SST, hold the water pump pulley.
Text in Illustration
*a
SST
SST: 09960-10010
09962-01000
09963-01000
(b) Remove the 4 bolts and water pump pulley.
34. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
3UR-FE LUBRICATION: OIL PUMP: REMOVAL; 2015 MY Tundra [0...
(a) Remove the bolt and No. 1 idler pulley sub-assembly.
35. REMOVE FAN BRACKET ASSEMBLY
(a) Remove the 4 bolts and fan bracket assembly.
36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
(a) Remove the standard bolt, 6 mm hexagon wrench bolt and
V-ribbed belt tensioner assembly.
37. REMOVE IGNITION COIL ASSEMBLY
(a) Remove the 8 bolts and 8 ignition coils.
38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
(a) Remove the 14 bolts, seal washer, cylinder head cover
sub-assembly LH and gasket.
HINT:
Make sure the removed parts are returned to the same
places they were removed from.
3UR-FE LUBRICATION: OIL PUMP: REMOVAL; 2015 MY Tundra [0...
(b) Remove the 5 gaskets from the No. 2 camshaft bearing cap
and No. 3 camshaft bearing cap.
39. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
(a) Remove the 14 bolts, seal washer, cylinder head cover
sub-assembly RH and gasket.
HINT:
Make sure the removed parts are returned to the same
places they were removed from.
(b) Remove the 5 gaskets from the No. 1 camshaft bearing cap
and No. 3 camshaft bearing cap.
40. REMOVE CRANKSHAFT PULLEY
(a) Using SST, loosen the crankshaft pulley set bolt.
Text in Illustration
*a
SST
*b
Turn
*c
Hold
SST: 09213-70011
SST: 09330-00021
(b) Partially install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.
3UR-FE LUBRICATION: OIL PUMP: REMOVAL; 2015 MY Tundra [0...
(c) Using the crankshaft pulley set bolt and SST, remove the
crankshaft pulley.
Text in Illustration
*a
SST
*b
Turn
*c
Hold
SST: 09950-50013
09951-05010
09952-05010
09953-05010
09954-05011
41. DISCONNECT WIRE HARNESS CLAMP BRACKET
(a) Remove the bolt and disconnect the wire harness clamp
bracket.
42. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
(a) Remove the 28 bolts and nut shown in the illustration.
Text in Illustration
*1
Nut
3UR-FE LUBRICATION: OIL PUMP: REMOVAL; 2015 MY Tundra [0...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст