Toyota Tundra (2015 year). Manual — part 1465
Last Modified: 9-16-2014
6.6 A
Doc ID: RM0000031YJ026X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENSOR: INSTALLATION; 2015 MY Tundra
[08/2014 - ]
INSTALLATION
1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
(a) Install the heated oxygen sensor to the front exhaust pipe
assembly by hand.
(b) Using SST, tighten the heated oxygen sensor.
SST: 09224-00010
Torque:
without SST -
44 N·m {449 kgf·cm, 32ft·lbf}
with SST -
40 N·m {408 kgf·cm, 30ft·lbf}
Text in Illustration
*a
Fulcrum length
HINT:
.
Make sure SST and the wrench are connected in a straight
line.
2. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
(a) Install the heated oxygen sensor to the front No. 2 exhaust
pipe assembly by hand.
3UR-FBE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENS...
(b) Using SST, tighten the heated oxygen sensor.
SST: 09224-00010
Torque:
without SST -
44 N·m {449 kgf·cm, 32ft·lbf}
with SST -
40 N·m {408 kgf·cm, 30ft·lbf}
Text in Illustration
*a
Fulcrum length
HINT:
.
Make sure SST and the wrench are connected in a straight
line.
3. INSTALL FRONT EXHAUST PIPE ASSEMBLY
4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
5. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
6. INSTALL PROPELLER SHAFT HEAT INSULATOR
7. INSPECT FOR EXHAUST GAS LEAK
3UR-FBE ENGINE CONTROL SYSTEM: HEATED OXYGEN SENS...
Last Modified: 9-16-2014
6.6 G
Doc ID: RM00000322N00OX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE ENGINE CONTROL SYSTEM: IGNITION RELAY NO. 2: ON-VEHICLE INSPECTION; 2015 MY
Tundra [08/2014 - ]
ON-VEHICLE INSPECTION
1. REMOVE INTEGRATION RELAY (UNIT E)
(a) Remove the engine room relay block cover.
(b) Using a screwdriver, detach the 2 claws and remove the
integration relay from the engine room relay block.
HINT:
Tape the screwdriver tip before use.
(c) Disconnect the 3 connectors.
2. INSPECT INTEGRATION RELAY (IG2)
NOTICE:
(1) Measure the resistance according to the value(s) in the table below.
3UR-FBE ENGINE CONTROL SYSTEM: IGNITION RELAY NO. 2:...
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
IG2 MAIN fuse
Always
Below 1 Ω
If the result is not as specified, replace the IG2 MAIN fuse.
(1) Measure the resistance according to the value(s) in the
table below.
Standard Resistance:
TESTER
CONNECTION
CONDITION
SPECIFIED
CONDITION
1C-1 - 1B-8
When battery voltage is not
applied to terminals 1B-6 and
1B-7
10 kΩ or higher
When battery voltage is
applied to terminals 1B-6 and
1B-7
Below 1 Ω
If the result is not as specified, replace the integration
relay.
3. INSTALL INTEGRATION RELAY (UNIT E)
(a) Connect the 3 connectors.
(b) Install the integration relay to the engine room relay block.
(c) Install the engine room relay block cover.
3UR-FBE ENGINE CONTROL SYSTEM: IGNITION RELAY NO. 2:...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст