Toyota Tundra (2015 year). Manual — part 2384
11. REMOVE CONSOLE BOX CARPET
(a) Remove the console box carpet.
12. REMOVE REAR CONSOLE BOX ASSEMBLY
(a) Disconnect the 2 connectors.
(b) Remove the 2 screws <E> and 4 bolts <B> and rear console box assembly.
13. REMOVE FRONT CONSOLE BOX
(a) Remove the 2 clips and detach the connector.
(b) Remove the 5 screws <E> and front console box.
14. REMOVE FRONT DOOR SCUFF PLATE LH
15. REMOVE COWL SIDE TRIM BOARD LH
16. REMOVE FRONT DOOR SCUFF PLATE RH
INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD (for Floo...
HINT:
Use the same procedure described for the LH side.
17. REMOVE COWL SIDE TRIM BOARD RH
HINT:
Use the same procedure described for the LH side.
18. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
19. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
20. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
21. REMOVE NO. 2 SWITCH HOLE BASE
(a) Apply protective tape as shown in the illustration.
Text in Illustration
*1
Protective Tape
(b) Detach the 4 clips and remove the No. 2 switch hole base.
(c) Disconnect each connector.
22. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT
(a) Apply protective tape as shown in the illustration.
Text in Illustration
*1
Protective Tape
(b) Detach the 3 clips, claw and remove the instrument cluster finish panel ornament.
23. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD (for Floo...
(a) Remove the 2 clips.
(b) Detach the 6 clips and remove the instrument cluster finish panel assembly.
24. REMOVE COMBINATION METER ASSEMBLY
25. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
26. REMOVE LOWER INSTRUMENT PANEL
27. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
28. REMOVE NO. 4 INSTRUMENT REGISTER SUB-ASSEMBLY
29. REMOVE INSTRUMENT SIDE PANEL RH
30. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH
31. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
32. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR
CONDITIONING CONTROL ASSEMBLY
33. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
34. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
35. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
36. REMOVE FRONT PILLAR GARNISH LH
37. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure described for the LH side.
38. REMOVE FRONT PILLAR GARNISH RH
39. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH
41. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD (for Floo...
42. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH
43. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
(a) for Manual Tilt Steering Column:
Operate the tilt lever to fully extend and lower the steering column.
(b) Disconnect each connector and each wire harness clamp.
(c) for Automatic Air Conditioning System:
Detach the 2 claws and disconnect the cooler thermistor.
Text in Illustration
*A
w/ Automatic Light Control System
*B
w/ Front Center Speaker
*C
for Automatic Air Conditioning System
-
-
(d) Apply protective tape as shown in the illustration.
INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD (for Floo...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст