Toyota Tundra (2015 year). Manual — part 143
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000004UD600XX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB5; Open in Outer Mirror
Indicator(Slave); 2015 MY Tundra [08/2014 - ]
DTC
C1AB5
Open in Outer Mirror Indicator(Slave)
DESCRIPTION
This DTC is stored when the blind spot monitor sensor LH detects an open in the blind spot monitor indicator LH.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1AB5
With the blind spot monitor main switch assembly (warning canceling
switch assembly) on, the current flowing to the indicator is below a
specified value when indicator operation voltage is sent to the
indicator.
Harness or connector
Outer rear view
mirror sub-assembly
LH
Outer rear view
mirror assembly LH
Blind spot monitor
sensor LH
WIRING DIAGRAM
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling
switch assembly) is on.
PROCEDURE
1.
CHECK DTC
(a) Clear the DTCs
.
(b) Recheck for DTCs and check if the same DTC is output again
.
OK:
No DTCs are output.
NG
GO TO STEP 2
OK
USE SIMULATION METHOD TO CHECK
2.
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH -
BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
(a) Disconnect the S5 blind spot monitor sensor LH connector.
(b) Disconnect the N5 outer rear view mirror assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
w/ Memory
w/o Memory
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
S5-4 (OMIL) - N5-9 (BSL+)
Always
Below 1 Ω
N5-5 (MLP-) - Body ground
Always
Below 1 Ω
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
S5-4 (OMIL) - N5-18 (BSL+)
Always
Below 1 Ω
N5-5 (MLP-) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
OK
3.
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
(a) Remove the outer rear view mirror assembly LH
.
(b) Remove the outer rear view mirror sub-assembly LH
.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
w/ Memory
w/o Memory
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
N5-9 (BSL+) - B-7 (+)
Always
Below 1 Ω
N5-5 (MLP-) - B-5 (-)
Always
Below 1 Ω
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
N5-18 (BSL+) - B-7 (+)
Always
Below 1 Ω
N5-5 (MLP-) - B-5 (-)
Always
Below 1 Ω
Text in Illustration
*A
w/ Memory
*B
w/o Memory
*a
Vehicle Side
*b
Outer Rear View Mirror Sub-assembly LH Side
NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY
LH
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
OK
4.
CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH
(a) Replace the outer rear view mirror sub-assembly LH with a new or normally functioning one
.
(b) Clear the DTCs
.
(c) Recheck for DTCs and check if the same DTC is output again
.
OK:
No DTCs are output.
NG
REPLACE BLIND SPOT MONITOR SENSOR LH
OK
END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY
LH IS DEFECTIVE)
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст