Toyota Tundra (2015 year). Manual — part 144
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000004S2T01NX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB6; Blind Spot Monitor Master
Module; 2015 MY Tundra [08/2014 - ]
DTC
C1AB6
Blind Spot Monitor Master Module
DESCRIPTION
This DTC is stored when the blind spot monitor sensor RH detects an internal malfunction.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1AB6
The blind spot monitor sensor RH (master) detects an internal
malfunction.
Blind spot monitor sensor
RH
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling
switch assembly) is on.
PROCEDURE
1.
CHECK DTC
(a) Clear the DTCs
.
(b) Recheck for DTCs and check if the same DTC is output again
.
OK:
No DTCs are output.
NG
REPLACE BLIND SPOT MONITOR SENSOR RH
OK
USE SIMULATION METHOD TO CHECK
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000004S2U01NX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB7; Blind Spot Monitor Slave Module;
2015 MY Tundra [08/2014 - ]
DTC
C1AB7
Blind Spot Monitor Slave Module
DESCRIPTION
This DTC is stored when the blind spot monitor sensor LH detects an internal malfunction.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1AB7
The blind spot monitor sensor LH (slave) detects an internal
malfunction.
Blind spot monitor sensor
LH
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling
switch assembly) is on.
PROCEDURE
1.
CHECK DTC
(a) Clear the DTCs
.
(b) Recheck for DTCs and check if the same DTC is output again
.
OK:
No DTCs are output.
NG
REPLACE BLIND SPOT MONITOR SENSOR LH
OK
USE SIMULATION METHOD TO CHECK
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
OK
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000004S2V01OX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: C1AB8; Destination Information
Undefined; 2015 MY Tundra [08/2014 - ]
DTC
C1AB8
Destination Information Undefined
DESCRIPTION
This DTC is stored when correct destination information is not sent from the main body ECU (driver side junction
block assembly) and destination information cannot be confirmed after a blind spot monitor has been replaced.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
C1AB8
The blind spot monitor sensor cannot communicate with
the main body ECU (driver side junction block assembly).
CAN communication system
Main body ECU (driver side
junction block assembly)
Blind spot monitor sensor LH
Blind spot monitor sensor RH
INSPECTION PROCEDURE
NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling
switch assembly) is on.
PROCEDURE
1.
CHECK DTC (CAN COMMUNICATION SYSTEM)
(a) Check for CAN Communication System DTCs
.
OK:
CAN communication system DTCs are not output.
NG
GO TO CAN COMMUNICATION SYSTEM
2.
REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
(a) Replace the main body ECU (driver side junction block assembly) with a new or normally functioning
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
NEXT
one.
3.
CHECK DTC
(a) Recheck for DTCs and check if the same DTC is output again
.
Result
RESULT
PROCEED TO
No DTC is output
A
DTC is output from the blind spot monitor sensor RH (master)
B
DTC is output from the blind spot monitor sensor LH (slave)
C
B
REPLACE BLIND SPOT MONITOR SENSOR RH
C
REPLACE BLIND SPOT MONITOR SENSOR LH
A
END (MAIN BODY ECU [DRIVER SIDE JUNCTION
BLOCK ASSEMBLY] IS DEFECTIVE)
PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM:...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст