Toyota Tundra (2015 year). Manual — part 1356

Torque:

6.0 N·m {61 kgf·cm, 53in·lbf}

(i) Connect the 2 clamps and air pump connector.

(j) Connect the clamp and ground wire with the bolt.

Torque:

8.0 N·m {82 kgf·cm, 71in·lbf}

(k) Connect the 4 connectors to the connector holder block.

(l) Connect the 2 heater hoses.

(m) Connect the No. 4 water by-pass hose.

(n) Connect the ECM connector and clamp.

HINT:

Refer to the following procedures to connect the ECM connector

.

23. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

(a) Connect the No. 2 fuel tube

.

1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALL...

24. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

(a) Connect the No. 1 fuel pipe

.

(b) Install the fuel pipe clamp.

25. INSTALL INTAKE MANIFOLD

26. INSTALL AIR TUBE SUB-ASSEMBLY LH

27. INSTALL VENTILATION HOSE ASSEMBLY

28. INSTALL EGR VALVE BRACKET

29. INSTALL EGR VALVE ASSEMBLY

30. CONNECT NO. 13 WATER BY-PASS HOSE

31. CONNECT NO. 12 WATER BY-PASS HOSE

32. INSTALL RADIATOR ASSEMBLY

33. INSTALL FAN SHROUD

34. INSTALL FAN AND GENERATOR V BELT

35. INSTALL RADIATOR SIDE DEFLECTOR LH

36. INSTALL RADIATOR SIDE DEFLECTOR RH

37. INSTALL RADIATOR GRILLE SUB-ASSEMBLY

38. CONNECT OUTLET RADIATOR HOSE

39. INSTALL INLET RADIATOR HOSE

40. INSTALL FRONT FENDER APRON SEAL REAR LH

41. INSTALL FRONT FENDER APRON SEAL LH

42. INSTALL FRONT FENDER APRON SEAL REAR RH

43. INSTALL FRONT FENDER APRON SEAL RH

44. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

45. INSTALL AIR CLEANER ASSEMBLY

1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALL...

(a) Install the air cleaner case with the 2 bolts.

Torque:

5.0 N·m {51 kgf·cm, 44in·lbf}

(b) Install the air cleaner element to the air cleaner case.

(c) Install the air cleaner cap.

(1) for Type A:

Install the air cleaner cap and fasten the 4 hook clamps.

(2) for Type B:

Install the air cleaner cap and fasten the 2 hook clamps.

(3) Connect the MAF meter connector.

(4) Attach the wire harness clamp.

46. INSTALL AIR CLEANER HOSE ASSEMBLY

(a) Install the air cleaner hose with the 2 clamps.

Torque:

4.0 N·m {41 kgf·cm, 35in·lbf}

1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALL...

(b) Connect the ventilation hose and vacuum sensing hose.

47. ADD ENGINE OIL

48. ADD ENGINE COOLANT

49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

50. INSPECT FOR OIL LEAK

51. INSPECT FOR COOLANT LEAK

52. INSPECT FOR EXHAUST GAS LEAK

53. INSPECT FOR FUEL LEAK

54. INSPECT SHIFT LEVER POSITION

(a) for Column Shift:

Refer to the following procedures

.

(b) for Floor Shift:

Refer to the following procedures

.

55. INSTALL V-BANK COVER SUB-ASSEMBLY

(a) Attach the 2 V-bank cover hooks to the bracket. Then align the

2 V-bank cover grommets with the 2 pins, and press down on

the V-bank cover to attach the pins.

56. INSTALL HOOD SUB-ASSEMBLY

1UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALL...