Toyota Tundra (2015 year). Manual — part 2759
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002H5D053X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: POWER STEERING: VANE PUMP (for 1UR-FE): REMOVAL; 2015 MY Tundra [08/2014 - ]
REMOVAL
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the
battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal
notice before proceeding with work
.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the
SRS system.
3. REMOVE V-BANK COVER SUB-ASSEMBLY
4. REMOVE AIR CLEANER ASSEMBLY
5. REMOVE NO. 1 ENGINE UNDER COVER
6. REMOVE FAN AND GENERATOR V BELT
7. DRAIN POWER STEERING FLUID
8. DISCONNECT WIRE HARNESS CLAMP
(a) Disconnect the wire harness clamp.
9. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE
(a) Slide the clip and disconnect the No. 1 oil reservoir to pump
hose.
Text in Illustration
*1
No. 1 oil reservoir to pump hose
10. DISCONNECT POWER STEERING OIL PRESSURE SENSOR CONNECTOR
POWER STEERING: VANE PUMP (for 1UR-FE): REMOVAL; 2015 ...
(a) Disconnect the power steering oil pressure sensor connector.
11. DISCONNECT PRESSURE FEED TUBE
(a) Remove the bolt and disconnect the pressure feed tube.
Text in Illustration
*1
Pressure Feed Tube
(b) Remove the gasket.
12. REMOVE VANE PUMP ASSEMBLY
(a) Remove the 2 bolts and vane pump assembly.
POWER STEERING: VANE PUMP (for 1UR-FE): REMOVAL; 2015 ...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002H5E034X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: POWER STEERING: VANE PUMP (for 1UR-FE): DISASSEMBLY; 2015 MY Tundra [08/2014 - ]
DISASSEMBLY
1. FIX VANE PUMP ASSEMBLY
(a) Using SST, hold the vane pump in a vise.
SST: 09630-00014
09631-00132
2. REMOVE POWER STEERING SUCTION PORT UNION
(a) Remove the bolt and suction port union from the vane pump.
(b) Using a screwdriver, remove the O-ring from the suction port union.
3. REMOVE FLOW CONTROL VALVE ASSEMBLY
(a) Remove the pressure port union.
(b) Remove the O-ring from the pressure port union.
(c) Remove the flow control valve and compression spring.
4. REMOVE VANE PUMP REAR HOUSING
POWER STEERING: VANE PUMP (for 1UR-FE): DISASSEMBLY; 20...
(a) Remove the 4 bolts and rear housing from the front housing.
(b) Using a screwdriver, remove the O-ring from the rear housing.
Text in Illustration
*a
Protective Tape
HINT:
Tape the screwdriver tip before use.
5. REMOVE VANE PUMP SHAFT SUB-ASSEMBLY WITH PULLEY
(a) Using 2 screwdrivers, remove the snap ring from the vane pump
shaft.
(b) Remove the vane pump shaft sub-assembly with pulley.
NOTICE:
Be careful not to drop or damage the vane pump shaft sub-assembly with pulley. If it is damaged, replace
the vane pump assembly.
6. REMOVE VANE PUMP ROTOR
(a) Remove the 10 vane plates.
NOTICE:
Take care not to drop the vane plate.
(b) Remove the vane pump rotor.
7. REMOVE VANE PUMP CAM RING
POWER STEERING: VANE PUMP (for 1UR-FE): DISASSEMBLY; 20...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст