Toyota Tundra (2015 year). Manual — part 636
(d) Install the drain plug.
Torque:
20 N·m {204 kgf·cm, 15ft·lbf}
71. INSTALL EXTENSION HOUSING REAR OIL SEAL
(a) Using SST and a hammer, tap in a new oil seal.
SST: 09308-60010
SST: 09950-70010
09951-07150
Standard depth:
3.35 to 3.45 mm (0.132 to 0.136 in.)
72. INSTALL EXTENSION HOUSING SUB-ASSEMBLY
Seal packing:
Toyota Genuine Seal Packing 1281,
Three Bond 1281 or equivalent
Seal diameter:
1.0 to 1.5 mm (0.0394 to 0.0591 in.)
(c) Install the extension housing with the 10 bolts.
Torque:
34 N·m {345 kgf·cm, 25ft·lbf}
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
73. INSTALL AUTOMATIC TRANSMISSION HOUSING
(b) Install the transmission housing with the 14 bolts.
Torque:
34 N·m {345 kgf·cm, 25ft·lbf}
74. INSTALL AUTOMATIC TRANSMISSION BREATHER
TUBE
(a) Coat a new O-ring with ATF and install it to the breather tube.
(b) Install the breather tube with the 2 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48in·lbf}
75. INSTALL TRANSMISSION OIL COOLER ASSEMBLY
(a) w/ Trailer Towing System:
(1) Coat 4 new O-rings with ATF.
(2) Install the 4 O-rings, transmission oil cooler and transmission oil thermostat to the automatic
transmission assembly with the 3 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
(b) w/o Trailer Towing System:
(1) Coat 4 new O-rings with ATF.
(2) Install the 4 O-rings, transmission oil cooler and
transmission oil cooler spacer to the automatic transmission
assembly with the 3 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
76. INSTALL SPEED SENSOR
(a) Coat 2 new O-rings with ATF, and install them to the speed
sensors.
(b) Install the 2 speed sensors.
(c) Install the 2 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48in·lbf}
77. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the
adjusting bolt.
(b) Install a new lock washer and the nut.
Torque:
6.9 N·m {70 kgf·cm, 61in·lbf}
(c) Temporarily install the control shaft lever RH.
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
(d) Turn the control shaft lever RH counterclockwise until it stops,
and then turn it clockwise 2 notches to set it to the N position.
(e) Remove the control shaft lever RH.
(f) Align the groove with the neutral basic line.
(g) Hold the switch in position and tighten the bolt.
Torque:
13 N·m {133 kgf·cm, 10ft·lbf}
(a) Install the control shaft lever RH with the washer and nut.
Torque:
16 N·m {163 kgf·cm, 12ft·lbf}
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст