Toyota Tundra (2015 year). Manual — part 634
52. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
(a) Install the 2 thrust needle roller bearings.
HINT:
ITEM
INSIDE
OUTSIDE
Bearing A
72.0 to 72.3 mm (2.83 to 2.85 in.)
85.3 to 85.6 mm (3.36 to 3.37 in.)
Bearing B
36.5 to 36.7 mm (1.437 to 1.445 in.)
52.9 to 53.2 mm (2.08 to 2.09 in.)
(b) Coat the clutch drum thrust washer with MP grease and install it to the clutch drum and input shaft
assembly.
(c) Install the clutch drum and input shaft drum assembly onto the
transmission case.
53. INSTALL OIL PUMP ASSEMBLY
(a) Coat a new O-ring with ATF, and install it to the oil pump.
(b) Install the 2 thrust bearing races to the front oil pump.
Thrust bearing race diameter:
ITEM
INSIDE
OUTSIDE
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
ITEM
INSIDE
OUTSIDE
Race A
74.3 to 74.6 mm (2.93 to 2.94 in.)
87.4 to 87.7 mm (3.44 to 3.45 in.)
Race B
38.0 to 38.3 mm (1.50 to 1.51 in.)
53.9 to 54.1 mm (2.12 to 2.13 in.)
transmission case.
(d) Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct
clutch drum.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
NOTICE:
Do not allow seal packing to contact the bolts' threads.
(f) Install the 10 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
NOTICE:
55. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL
(a) Using SST, tap in 2 new oil seals.
SST: 09350-30020
09350-07110
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
(a) Install a new spacer to the manual valve lever.
(b) Push the manual valve lever shaft through the transmission case, and install the manual valve lever to the
shaft.
(c) Using a hammer, tap in a new spring pin.
(d) Align the manual valve lever indentation with the spacer hole,
and stake them together with the punch.
(e) Check that the shaft rotates smoothly.
57. INSTALL PARKING LOCK PAWL
(a) Install a new E-ring to the shaft.
(b) Install the parking lock pawl, shaft and spring.
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
58. INSTALL PARKING LOCK ROD SUB-ASSEMBLY
(a) Connect the parking lock rod to the manual valve lever.
59. INSTALL PARKING LOCK PAWL BRACKET
(a) Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.
Torque:
18 N·m {184 kgf·cm, 13ft·lbf}
(b) Move the manual valve lever to the P position, and confirm that
the planetary ring gear is correctly locked by the lock pawl.
60. INSTALL B-1 ACCUMULATOR VALVE
(a) Install the 2 springs and accumulator valve to the hole.
Spring diameter:
SPRING
FREE LENGTH
OUTER DIAMETER
COLOR
B-1 Inner
44.98 mm (1.77 in.)
11.30 mm (0.445 in.)
Natural
B-1 Outer
46.36 mm (1.83 in.)
17.10 mm (0.673 in.)
Natural
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст