Toyota Tundra (2015 year). Manual — part 855
(f) Using SST, press the universal joint spider bearing into the
propeller shaft yoke until the groove can be seen.
SST: 09336-16010
SST: 09950-40011
09951-04020
09952-04010
09953-04020
09954-04020
09955-04051
09957-04010
SST: 09950-60010
09951-00290
Text in Illustration
*a
Spider Bearing
*b
Turn
*c
Hold
NOTICE:
Confirm that the universal joint spider moves smoothly while
pressing in the bearing.
(g) Using needle-nose pliers, install the previously selected snap
Use the same installation procedure for the universal joint spider
bearing on the opposite side.
(h) Align the matchmarks on the propeller shaft yoke and universal joint yoke, and temporarily install the
spider and 2 universal joint spider bearings into the universal joint yoke.
(i) Using SST, press the universal joint spider bearing into the
universal joint yoke until the groove can be seen.
SST: 09336-16010
SST: 09950-40011
09951-04020
09952-04010
09953-04020
09954-04020
09955-04051
09957-04010
SST: 09950-60010
09951-00290
Text in Illustration
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 2WD):...
*a
Spider Bearing
*b
Turn
*c
Hold
(j) Using needle-nose pliers, install the previously selected snap ring into the groove on the universal joint
yoke.
HINT:
Use the same installation procedure for the universal joint spider bearing on the opposite side.
4. INSPECT PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING
(a) Check the spider bearings for wear and damage.
(b) Measure each spider bearing's axial play by turning the yoke while holding the shaft tightly.
Maximum bearing axial play:
0.05 mm (0.00197 in.)
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 2WD):...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002HBL00BX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 2WD): INSTALLATION; 2015 MY Tundra [08/2014
- ]
INSTALLATION
1. MEASURE EXTENSION HOUSING AND DIFFERENTIAL FLANGE ANGLE
NOTICE:
Perform the inspection on a level surface.
Perform the inspection with the vehicle empty.
Perform the inspection with all wheels on the ground.
HINT:
As the extension housing and rear differential flange angles are necessary when measuring the installation
housing flange (A).
SST: 09370-50010
Text in Illustration
*a
Extension Housing Flange Angle: A
SST: 09370-50010
Text in Illustration
*a
Rear Differential Flange Angle: B
2. TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 2WD):...
(b) for 1UR-FE:
Remove SST from the transmission.
SST: 09325-40010
(c) for 3UR-FE:
Remove SST from the transmission.
SST: 09325-60010
(d) Insert the sleeve yoke into the transmission.
(e) w/o Bearing Washer:
(1) Temporarily install the center support bearing to the
crossmember with the 2 mounting bolts.
(f) w/ Bearing Washer:
(1) Temporarily install the center support bearing to the
crossmember with the 2 bearing washers and 2 mounting
bolts.
Text in Illustration
*1
No. 2 Center Support Bearing Washer
*2
No. 1 Center Support Bearing Assembly
*a
Frame
(g) Align the matchmarks on the propeller shaft flange and
differential flange.
Text in Illustration
*a
Matchmark
PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY (for 2WD):...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст