Toyota Tundra (2015 year). Manual — part 1554
INSPECTION PROCEDURE
HINT:
Bank 2 refers to the bank that does not include the No. 1 cylinder.
PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
(a) Disconnect the D40 or D41 VVT sensor (for exhaust side)
connector.
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P036...
OK
OK
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
D40-3 (VC2) - Body ground
Ignition switch ON
4.5 to 5.0 V
D41-3 (VC2) - Body ground
Ignition switch ON
4.5 to 5.0 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
2.
CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM)
(a) Disconnect the D40 or D41 VVT sensor (for exhaust side) connector.
(b) Disconnect the D74 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
D40-1 (EX+) - D74-69 (EV1+)
Always
Below 1 Ω
D40-2 (EX-) - D74-68 (EV1-)
Always
Below 1 Ω
D41-1 (EX+) - D74-64 (EV2+)
Always
Below 1 Ω
D41-2 (EX-) - D74-65 (EV2-)
Always
Below 1 Ω
D40-1 (EX+) or D74-69 (EV1+) - Body ground
Always
10 kΩ or higher
D40-2 (EX-) or D74-68 (EV1-) - Body ground
Always
10 kΩ or higher
D41-1 (EX+) or D74-64 (EV2+) - Body ground
Always
10 kΩ or higher
D41-2 (EX-) or D74-65 (EV2-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
3.
CHECK SENSOR INSTALLATION (VVT SENSOR (FOR EXHAUST SIDE))
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P036...
OK
OK
OK
NEXT
(a) Check the VVT sensor (for exhaust side) installation.
OK:
Sensor is installed correctly.
NG
SECURELY REINSTALL SENSOR
4.
CHECK EXHAUST CAMSHAFT
Teeth do not have any cracks or deformation.
NG
REPLACE EXHAUST CAMSHAFT
5.
CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND)
NG
CHECK ENGINE MECHANICAL SYSTEM
6.
REPLACE VVT SENSOR (FOR EXHAUST SIDE)
(a) Replace the VVT sensor (for exhaust side)
.
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P036...
7.
CHECK WHETHER DTC OUTPUT RECURS
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear DTCs
.
(e) Start the engine.
(f) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving
Pattern.
(g) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(h) Read DTCs.
Result
DISPLAY (DTC OUTPUT)
PROCEED TO
No output
A
P0365, P0367, P0368, P0390, P0392 or P0393
B
HINT:
If the engine does not start, replace the ECM.
B
REPLACE ECM
A
END
3UR-FBE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0365,P036...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст