Toyota ProAce (2017 year). Instruction — part 19
In the event of a breakdown
Dipped beam headlamps
Daytime running lamps /
sidelamps (halogen headlamps)
(halogen headamps)
Type A, P21-5W
Type C, H7-55W
F Pull out the cover.
F Turn the bulb holder a quarter turn
F Press the lower clip on the electrical
clockwise.
connector and remove the assembly of
F Remove the bulb holder.
connector and bulb.
F Change the failed bulb.
F Pull the bulb out and change it.
To refit, carry out these operations in reverse
To refit, carry out these operations in reverse
order.
order.
When refitting the connector and bulb
in the lamp, push the assembly into its
housing until it clicks into place.
306
In the event of a breakdown
Main beam headlamps
Direction indicators
(halogen headlamps)
(halogen headlamps)
Type C, H1-55W
Type B, PY21W-21W (amber)
F Pull out the cover.
F Turn the bulb holder a quarter turn
F Press the lower clip on the electrical
clockwise.
connector and remove the assembly of
F Remove the bulb holder.
connector and bulb.
F Change the failed bulb.
F Pull the bulb out and change it.
To refit, carry out these operations in reverse
To refit, carry out these operations in reverse
order.
order.
8
Be aware that the area behind the right-
Faster flashing of a direction indicator
hand headlamp (facing forwards) may
warning lamp (left or right) indicates a
be hot, with the risk of burns (overflow
failed bulb on that side.
pipe).
307
In the event of a breakdown
Dipped beam headlamps
Main beam headlamps
Direction indicators
(xenon headlamps)
(xenon headlamps)
(xenon headlamps)
Type E, D8S 25W
Type C, H1-55W
Type B, PY21W-21W (amber)
F Pull out the cover.
F Turn the bulb holder a quarter turn
F Press the lower clip on the electrical
clockwise.
Replacement of D8S xenon bulbs must
connector and remove the assembly of
F Remove the bulb holder.
be done by an authorized Toyota dealer
connector and bulb.
F Change the failed bulb.
or repairer, or another duly qualified and
F Pull the bulb out and change it.
To refit, carry out these operations in reverse
equipped professional as there is a risk
To refit, carry out these operations in reverse
order.
of electrocution.
order.
It is recommended that both D8S bulbs
be replaced at the same time, in the
event of the failure of one of them.
When refitting the connector and bulb
Faster flashing of a direction indicator
in the lamp, push the assembly into its
warning lamp (left or right) indicates a
housing until it clicks into place.
failed bulb on that side.
308
In the event of a breakdown
Daytime running lamps /
Front foglamps
sidelamps
Type C, H11-55W
(xenon headlamps)
F Press the locking clip and disconnect the
connector.
Contact an authorized Toyota dealer or
F Turn the bulb holder a quarter turn
repairer, or another duly qualified and equipped
F Below the front bumper, unscrew the fixing
anti-clockwise.
professional for the replacement of this type of
screws for the deflector A.
F Remove the bulb holder.
LED lamp and light, guide.
F Remove the deflector A.
F Change the failed bulb.
A replacement kit for the LEDs is available from
To refit, carry out these operations in reverse
Toyota dealers.
order.
8
You can also go to an authorized Toyota
dealer or repairer, or another duly
qualified and equipped professional for
the replacement of these bulbs.
309
In the event of a breakdown
F Identify the failed bulb then open the rear
Rear lamps (rear wing
doors.
doors with glass windows)
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
F Spread the three lugs slightly, then extract
the bulb holder.
F Remove the failed bulb by pressing
lightly on it, then turning it a quarter turn
F
From inside, remove the ventilation grille, if
clockwise.
your vehicle has one.
F Change the bulb.
F
From outside, unscrew the two lamp fixing
To reassemble, carry out these operations in
screws.
reverse order.
1.
Brake lamps / sidelamps.
Type B, P21/5W-21/5W
2.
Direction indicators.
Type B, PY21W-21W (amber)
3.
Reversing lamps.
Type B, P21W-21W
4.
Foglamps / sidelamps.
Type B, P21/4W-21/4W
For vehicles with interior trim, contact
F While holding the lamp in place, press the
an authorized Toyota dealer or repairer,
clip on the inside then carefully remove the
or another duly qualified and equipped
lamp.
professional to have the work done.
F Disconnect the electrical connector.
310
In the event of a breakdown
Third brake lamp (rear wing
Number plate lamps (rear wing
doors with glass windows)
doors with glass windows)
Type A, W5W-5W
Type A, W5W-5W
F Remove the plastic cover using a small
screwdriver.
F Using a screwdriver through the aperture,
push the lamp towards the outside.
F Open the left hand rear door.
F Insert a thin screwdriver into one of the cut-
F Disconnect the electrical connector.
outs in the lens.
F Remove the lamp.
F Push it outwards to unclip it.
F Turn the bulb holder a quarter turn anti-
F Remove the lens.
clockwise.
F Change the failed bulb.
F Change the failed bulb.
To refit, press on the lamp to clip it in place.
To refit, press on the lens to clip it in place.
8
311
In the event of a breakdown
Courtesy lamps
(front and rear)
Type A, W5W-5W
F Unclip the lens by inserting a thin
screwdriver into the cut-outs at each side
of the lamp.
F Pull the bulb out and change it.
F Clip the lens in place and ensure that it is
secure.
312
In the event of a breakdown
F Identify the failed bulb then open the boot.
Rear lamps
(rear tailgate)
For more information on Changing a bulb and
in particular, the types of bulbs, refer to the
corresponding section.
F While holding the lamp in place, press the
clip on the inside then carefully remove the
lamp.
F Disconnect the electrical connector.
F From inside, remove the cover, if your
vehicle has one.
1. Brake lamps / sidelamps.
Type B, P21/5W-21/5W
2. Direction indicators.
Type B, PY21W-21W (amber)
F Spread the three lugs slightly, then extract
3. Reversing lamps.
the bulb holder.
Type B, P21W-21W
F Remove the failed bulb by pressing
4. Foglamps / sidelamps.
lightly on it, then turning it a quarter turn
8
Type B, P21/4W-21/4W
clockwise.
F Change the bulb.
F From the outside, press on the inner clips
For vehicles with interior trim, contact
on the plastic finisher then tip it towards the
an authorized Toyota dealer or repairer,
outside to remove it.
To reassemble, carry out these operations in
or another duly qualified and equipped
F Unscrew the two lamp fixing screws.
reverse order.
professional to have the work done.
313
In the event of a breakdown
Third brake lamp
Number plate lamps
(rear tailgate)
(rear tailgate)
Type A, W5W-5W
Type A, W5W-5W
F Unclip the trim at each end by turning it
upwards.
F Pull on the trim to disengage the central
clips, then remove it.
F Using a screwdriver through the aperture,
F Open the rear tailgate.
F Insert a thin screwdriver into one of the cut-
push the lamp towards the outside.
outs in the lens.
F Disconnect the electrical connector.
F Push it outwards to unclip it.
F Remove the lamp.
F Remove the lens.
F Turn the bulb holder a quarter turn anti-
F Change the failed bulb.
clockwise.
F Change the failed bulb.
To refit, carry out these operations in reverse
To refit, press on the lens to clip it in place.
order.
To refit the lamp and trim, press on them to clip
them in place.
314
In the event of a breakdown
Courtesy lamps
Platform cab
(front and rear)
For the replacement of this type of LED lamp
Rear lamps
and light guide, contact an authorized Toyota
For more information on Changing a bulb and
F Identify the failed bulb.
dealer or repairer, or another duly qualified and
in particular, the types of bulbs, refer to the
F Remove the four screws securing the lens.
equipped professional.
corresponding section.
F Pull the lens towards you.
A replacement kit for the LEDs is available from
F Remove the failed bulb by pressing lightly
Toyota dealers.
on it and then turning it a quarter turn
1. Direction indicators.
clockwise.
Type B, P21W-21W
F Change the bulb.
2. Brake lamps.
Type B, P21W-21W
3. Sidelamps.
Type B, R10W-10W
To reassemble, carry out these operations in
8
4. Reversing lamps.
reverse order.
Type B, P21W-21W
5. Foglamps.
Type B, P21W-21W
315
In the event of a breakdown
Changing a fuse
Access to the tools
Changing a fuse
Before changing a fuse:
F the cause of the failure must be identified
and rectified,
F all electrical consumers must be
switched off,
F the vehicle must be immobilised with the
ignition off,
Good
Failed
F identify the failed fuse using the tables and
layout drawings in the following pages.
The extraction tweezer is located behind the
To replace a fuse, you must:
fusebox cover, on the dashboard pillar.
F use the special tweezer to extract the fuse
from its housing and check the condition of
Tweezer
its filament.
F Unclip the cover by pulling at the top left, then
F always replace the failed fuse with a fuse
right.
of the same rating (same colour); using
F Disengage the cover completely and turn it over,
a different rating could cause faults (risk
F Take the tweezer from its housing.
of fire).
If the fuse fails again soon after replacement,
The replacement of a fuse not shown in
have the vehicle's electrical system checked
the tables below may cause a serious
by an authorized Toyota dealer or repairer,
malfunction of your vehicle. Contact an
or another duly qualified and equipped
authorized Toyota dealer or repairer,
professional.
or another duly qualified and equipped
professional.
316
In the event of a breakdown
Dashboard fuses
Installing electrical
accessories
Your vehicle's electrical system is
The fusebox is placed in the lower dashboard
designed to operate with standard or
(left-hand side).
optional equipment.
Before installing other electrical
equipment or accessories on your
Access to the fuses
vehicle, contact an authorized Toyota
dealer or repairer, or another duly
qualified and equipped professional.
Toyota will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying malfunctions
resulting from the installation of
accessories not supplied and not
recommended by Toyota and not
installed in accordance with its
instructions, in particular when the
F Unclip the cover by pulling at top left, then
combined consumption of all of the
right.
additional equipment connected
exceeds 10 milliamperes.
8
For more information on installing a
towbar or equipment of the TAXI type,
contact a Toyota dealer.
317
In the event of a breakdown
Version 1 (Eco)
Fuse
Rating
Functions
The fuses described hereafter vary according
N°
(A)
to the equipment in your vehicle.
F1
10
Electric power steering, clutch switch
F4
15
Horn.
F5
20
Front/rear screenwash pump.
F6
20
Front/rear screenwash pump.
F7
10
Rear 12 V accessory socket.
F8
20
Single or double rear wipers.
F10/F11
30
Front and rear, exterior, interior locks.
Front air conditioning controls, radio controls, gear lever,
F13
10
head-up display.
F14
5
Alarm, ERA-GLONASS emergency call system.
F17
5
Instrument panel.
F19
3
Steering mounted controls.
F21
3
"Smart Entry & Start System" system or ignition switch.
Rain and sunshine sensor, multifunction detection
F22
3
camera.
F23
5
Seat belt unfastened or not fastened display screen.
F24
5
Touch screen, reversing camera and parking sensors.
F25
5
Airbags.
F29
20
Audio system, touch screen, CD player, navigation.
F31
15
Audio system (battery +).
F32
15
Front 12 V accessory socket.
Blind spot monitoring system, door mirror electric
F34
5
controls.
Heated washer jets, headlamp beam height
F35
5
control.
F36
5
Torch charger, rear courtesy lamp.
318
In the event of a breakdown
Version 2 (Full)
Fuse
Rating
Functions
N°
(A)
The fuses described hereafter vary according
F1
3
"Smart Entry & Start System" system or ignition switch.
to the equipment in your vehicle.
F5
5
Touch screen, reversing camera and parking sensors.
F7
10
Rear air conditioning controls, Hi-Fi amplifier.
F8
20
Single or double rear wiper.
F10/F11
30
Front and rear, exterior, interior locks.
F12
3
Alarm.
F17
10
Rear 12 V accessory socket.
F18
5
ERA-GLONASS emergency call system.
F21
3
Torch charger, rear courtesy lamp.
F22
3
Glove box lamp, rear courtesy lamps.
Blind spot monitoring system, door mirror electric
F23
5
controls.
F24
5
Steering mounted controls.
F25
5
Headlamp beam height control.
F26
3
Seat belt unfastened or not fastened display screen.
Rain and sunshine sensor, multifunction detection
F27
3
camera.
Front air conditioning controls, radio controls, gear lever,
F28
10
head-up display.
8
F30A or B
15
Audio system (battery +).
F31
5
Airbags.
F33
15
Front 12 V accessory socket.
F35
5
Instrument panel.
F36
20
Audio system, touch screen, CD player, navigation.
319
In the event of a breakdown
The fuses described hereafter vary according to the equipment in your vehicle.
Engine compartment
fuses
Fuse
Rating
Functions
The fusebox is located in the engine
N°
(A)
compartment near the battery.
F12
5
Heated washer jets.
F14
25
Front and rear screenwash pump.
Access to the fuses
Front radar and emergency braking, electric power
F15
5
steering.
F17
10
Built-in systems interface.
F19
30
Front wiper motor.
F20
15
Front and rear screenwash pump.
F21
20
Headlamp wash pump.
F22
15
Horn.
F23
15
Right hand main beam headlamp.
F Release the two latches A.
F24
15
Left hand main beam headlamp.
F Remove the cover.
F Change the fuse.
F When you have finished, close the cover
carefully then engage the two latches A, to
ensure correct sealing of the fusebox.
320
In the event of a breakdown
Access to the battery
12 V battery
The battery is located under the bonnet.
Procedure for starting the engine using another
F Open the bonnet using the interior release
battery or charging a discharged battery.
lever, then the exterior safety catch.
F Secure the bonnet stay.
General points
Lead-acid starter batteries
Batteries contain harmful substances
Protect your eyes and face before
such as sulphuric acid and lead.
handling the battery.
They must be disposed of in
All operations on the battery must be
accordance with regulations and must
carried out in a well ventilated area and
not, in any circumstances, be discarded
away from naked flames and sources
with household waste.
of sparks, so as to avoid the risk of
Take used remote control batteries and
explosion or fire.
F If fitted to your vehicle, remove the plastic
vehicle batteries to a special collection
Wash your hands afterwards.
cover to access the (+) terminal.
point.
The battery (-) terminal is not accessible.
A remote earth point is provided at the front of
the vehicle.
Versions equipped with Stop & Start are
If your vehicle has an automatic
fitted with a 12 V lead-acid battery of
gearbox, do not try to start the engine
specific technology and specification.
by pushing the vehicle.
For more information on the Bonnet
8
Its replacement should be carried out
and Engine, refer to the corresponding
only by an authorized Toyota dealer or
section(s).
repairer, or another duly qualified and
equipped professional.
321
In the event of a breakdown
F
Wait until the engine returns to idle then
Starting using another
disconnect the jump lead cables in the
battery
reverse order.
When your vehicle's battery is discharged, the
F
Refit the plastic cover to the (+) terminal,
engine can be started using a slave battery
if your vehicle has one.
(external or on another vehicle) and jump lead
F
Allow the engine to run for at least
cables or a battery booster.
30 minutes, by driving or with the vehicle
stationary, so that the battery reaches an
adequate state of charge.
Never try to start the engine by
connecting a battery charger.
Never use a 24 V or higher battery
F
Raise the plastic cover on the (+) terminal,
Some functions, including Stop & Start,
booster.
if your vehicle has one.
are not available if the battery is not
First check that the slave battery has a
F
Connect the red cable to the positive
sufficiently charged.
nominal voltage of 12 V and a capacity
terminal (+) of the flat battery A (at
at least equal to that of the discharged
the metal elbow) then to the positive
battery.
terminal (+) of the slave battery B or the
The two vehicles must not be in contact
booster.
with each other.
F
Connect one end of the green or black
Switch off the electrical consumers on
cable to the negative terminal (-) of the
both vehicles (audio system, wipers,
slave battery B or the booster (or earth
lighting, ...).
point on the other vehicle).
Ensure that the jump lead cables do
F
Connect the other end of the green or black
not pass close to moving parts of the
cable to the earth point C on the broken
engine (cooling fan, belts, ...).
down vehicle.
Do not disconnect the (+) terminal when
F
Start the engine of the vehicle with the
the engine is running.
good battery and leave it running for a
few minutes.
F
Operate the starter on the broken down
vehicle and let the engine run.
If the engine does not start straight away,
switch off the ignition and wait a few moments
before trying again.
322
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст