Toyota ProAce (2017 year). Instruction — part 6
Access
The doors and the overall
Safety / Obstacle detection with
Fuel filler flap
dimensions of the vehicle
electric door(s)
2
When open, a door projects beyond the body.
The obstacle detection system is triggered
If fitted to your vehicle, never open the
Be sure to take this into account when you park
when the moving door encounters an obstacle
left-hand sliding side door when the
alongside a wall, a post or a high kerb...
with a certain level of physical resistance.
fuel filler flap is open. Otherwise you
-
If an obstacle is detected while the door is
risk damaging the fuel filler flap and the
closing, the door stops then opens fully.
sliding door and causing injury to the
-
If an obstacle is detected while the door is
person filling the vehicle.
opening, the door stops and then closes.
-
If an obstacle is detected twice in
succession during a movement of the door,
If the fuel filler flap is open and your
it will no longer close electrically. Close the
vehicle has an electric left-hand sliding
door manually to reinitialise it.
side door, the door cannot be opened
using the opening control button. If
required the door can be opened half
way manually. The fuel filler flap must
be closed to allow the door to open
When open, a door never projects
correctly
beyond the rear bumper.
85
Access
On a steep slope
Reinitialising electric doors
Following disconnection of the battery with the
doors open, it may be necessary to close the
doors manually to reinitialise them.
If the doors no longer work electrically,
reinitialise the door(s) as follows:
F Fully close the door(s) manually.
F Fully open the door(s) manually.
F Close the door(s) manually.
F Fully open the door(s) manually.
However, if your vehicle is on a slope, with the
F Close the door(s) manually.
front of the vehicle facing down, the door may
On completion of this procedure, electric
not stay open and may close again jerkily with
operation of the doors is restored.
the risk of injury.
However, if a problem persists following this
It is possible to open and close the doors
procedure, contact an authorized Toyota
electrically on slopes of up to 20%.
In the case of a steep slope, the door
dealer or repairer, or another duly qualified and
However, if your vehicle is on a slope, with the
may be driven by its own weight and
equipped professional.
front of the vehicle facing up, open the door
as a consequence may open or close
with care. The door may open more quickly due
jerkily.
to the incline.
There would not be time for action at
On a steep slope, guide the side door manually
the electric controls to take effect.
to help it to close.
There would not be time for the
obstacle detection system to react.
Take care not to leave the vehicle on
a steep slope with the door(s) open
without supervision. If this advice is not
followed, injuries or damage may occur
if a person or an object is trapped or
caught.
86
Access
Kick-activated side doors opening and locking
Before making the movement with your
foot, ensure that you are steady and
2
well positioned, so that you do not lose
your balance (rain, snow, ice, mud, ...).
Take care not to touch the exhaust
tailpipe when making the movement
with your foot - risk of burns.
F Pass your foot below the rear bumper then
remove it, as though kicking (upwards).
By keeping the remote control on your person
The sensor detects your foot approaching and
and with a movement of your foot, the system
leaving and triggers opening or closing of the
unlocks and opens the sliding side door or
side door.
closes and locks it.
The remote control must be located at the rear
of the vehicle, more than about 30 cm and less
than about 2 m from the vehicle.
Make the movement without interruption
and do not repeat it immediately
afterwards or several times.
If the door does not open, wait about
2 seconds before trying again.
The automatic locking after closing the
Do not leave your foot in the air.
door is programmable in the vehicle
configuration menu.
87
Access
Opening
Cab and loading area selectivity
deactivated.
If the vehicle is locked, it is unlocked before
If the vehicle is locked, it is unlocked before
opening the door.
opening the door.
Cab and loading area selectivity
activated.
If the vehicle is locked, the loading area is
With "Hands-free access" activated in the
unlocked before opening the door.
vehicle configuration menu.
F With the remote control on your person and
in the recognition zone A, pass your foot
under the outer rear bumper, on the side
For more information on the Key,
you want to open the door.
Remote control or Smart Entry
& Start System, and in particular
total or selective locking, refer to the
Confirmation that the door is going
corresponding section.
to open is signalled by the direction
indicators flashing for a few seconds,
accompanied by an audible signal.
The movement of the door is reversed
if you pass your foot under the bumper
during operation of the door.
If fitted to your vehicle, the electric door
mirrors unfold on unlocking the vehicle.
88
Access
Closing
Deactivation
With the audio system
By default, hands-free access is activated.
The function can be deactivated in the vehicle
configuration menu.
2
In the "Personalisation-Configuration" menu,
activate/deactivate "Hands-free access".
Automatic locking
The vehicle locks itself following the kick-
With the touch screen
activated closing of a sliding door.
With "Hands-free access" activated in the
The automatic locking can be deactivated in
vehicle configuration menu.
the vehicle configuration menu.
F With the remote control on your person and
in the recognition zone A, pass your foot
In the vehicle settings menu, activate/
under the outer rear bumper, on the side
If your vehicle is not fitted with an
deactivate "Hands-free access".
you want to close the door.
alarm, locking is confirmed by fixed
illumination of the direction indicators
Once the door has closed, the vehicle locks
for about two seconds.
itself automatically, if "Hands-free access
Depending on version, the door mirrors
self-locking" has been selected in the vehicle
fold at the same time.
Then, if you want automatic locking after
configuration menu.
closing the door, activate/deactivate "Hands-
free access self-locking".
Confirmation that the door is going
to close is signalled by the direction
indicators flashing for a few seconds,
Operating fault
accompanied by an audible signal.
The movement of the door is reversed
An audible signal repeated three times
if you pass your foot under the bumper
indicates a fault with the system.
during operation of the door.
If fitted to your vehicle, the electric door
Contact an authorized Toyota dealer or
mirrors fold on locking the vehicle.
repairer, or another duly qualified and equipped
professional to have the system checked.
89
Access
If "Hands-full access self-locking" is
The sliding door may open or close
selected in the vehicle menu and after
erratically if:
closing the door, check that your vehicle
-
your vehicle is fitted with a towbar,
has locked correctly.
-
you attach or detach a trailer,
This is because locking will not take
-
you fit or remove a bicycle carrier,
place:
-
you load or unload bicycles on a
-
if the ignition is on,
bicycle carrier,
-
if one of the doors or the rear
-
you remove or raise something
tailgate is open,
behind the vehicle,
-
if a "Smart Entry & Start System"
-
an animal approaches the bumper,
remote control is inside the vehicle.
-
you wash your vehicle,
If a number of gestures with your foot
-
a service is being carried out on
have no effect, wait a few seconds
your vehicle,
before starting again.
-
you change a wheel.
The system is automatically deactivated
To avoid unwanted operation, keep the
in heavy rain or with accumulations of
key away from the detection zone or
snow.
deactivate the function in the vehicle
If the system fails to work, check that
configuration menu.
the remote control is not exposed to a
source of electromagnetic interference
(smartphone, ...).
Operation may be affected if using a
prosthetic leg.
This system may not work correctly if
your vehicle is fitted with a towbar.
Ensure that no person or object could
prevent the correct opening or closing
of the doors.
Be aware of children when operating
the doors.
90
Access
Closing
Rear wing doors
F Close first the right-hand door, then the
with glass windows
left-hand door.
The rear wing doors with glass windows are
2
asymmetrical.
The left-hand door is fitted with a lock.
If the left-hand door is closed
first, a buffer stop located on
From outside
the edge of the right-hand door
prevents it closing.
F
After first opening the left-hand door, pull
the lever A towards you to open the right-
hand door.
If the left-hand door is not fully closed
(the right-hand door is not detected):
-
vehicle stationary and engine
running, this warning lamp
comes on, accompanied by an
F
After unlocking the vehicle (using the key,
alert message for a few seconds,
remote control or Smart Entry & Start
-
vehicle moving (speed above
System, depending on equipment) pull the
6 mph (10 km/h)), this warning
door handle.
lamp comes on, accompanied
by an audible signal and an alert
message for a few seconds.
For more information on the Key,
Remote control or Smart Entry
& Start System and in particular
unlocking the vehicle, refer to the
corresponding section.
91
Access
Opening to approximately 180°
Opening to about 250°
If fitted to your vehicle, the hinges include
three notches which allow the door to be held
open at 90°, 180° or 250°.
If fitted to your vehicle, a check strap system
that allows the doors to be opened from
about 90° to about 180°.
F Pull the yellow control when the door is
open.
The check strap will engage again
automatically on closing.
When parked with the rear doors
open to 90°, the doors mask the rear
lamps. To signal your position to
other road users driving in the same
direction who may not have seen
F Open the door to the desired position.
your vehicle, use a warning triangle
or other device required by the
legislation in your country.
92
Access
From inside
Vehicle locked and child lock off (deactivated).
Cab and loading area selectivity
activated and the vehicle locked.
2
F Twist this handle down to totally unlock the
vehicle and open the right-hand door.
F Twist this handle down to unlock the
loading area and open the right-hand
door.
Vehicle unlocked and child lock off
(deactivated).
Opening
Door or vehicle unlocked.
F Twist this handle down to open the right-
hand door.
F Twist this handle down to open the right-
hand door.
If the child lock is on (activated), the
Cab and loading area selectivity
handle is inoperative.
deactivated and the vehicle
locked.
Vehicle locked.
For more information on the Child lock,
F Twist this handle down to totally unlock the
F Twist this handle down to totally unlock the
refer to the corresponding section.
vehicle and open the right-hand door.
vehicle and open the right-hand door
Closing
Vehicle unlocked.
F First close the right-hand door, then the
F Twist this handle down to open the right-
left-hand door.
hand door.
93
Access
Closing
Back-up control
Rear tailgate
It allows the mechanical unlocking of the rear
Opening
tailgate in the event of a battery or central
locking system malfunction.
Unlocking
F If fitted to your vehicle and if necessary,
fold back the rear seats to gain access to
the lock from inside.
F
Lower the rear tailgate using the interior grab
handle then push it home to fully close it.
If the rear tailgate is not fully closed:
F
After unlocking the vehicle with the key, the
remote control or the Smart Entry & Start
System, pull the handle, then raise the rear
-
vehicle stationary and engine running, this
tailgate.
warning lamp comes on, accompanied by
an alert message for a few seconds,
-
vehicle moving (speed above 6 mph
(10 km/h)), this warning lamp comes on,
F Insert a small screwdriver into hole A of the
accompanied by an audible signal and an
lock to unlock the rear tailgate.
alert message for a few seconds.
F Move the latch to the left.
For more information on the Key,
For more information on the Key,
Remote control or Smart Entry
Remote control or Smart Entry
Locking after closing
& Start System and in particular
& Start System and in particular
unlocking the vehicle, refer to the
on locking the vehicle, refer to the
If the fault persists after closing again, the rear
corresponding section.
corresponding section.
tailgate will remain locked.
94
Access
Volumetric
Total protection
Alarm
The system monitors variations in volume in the
Activation
cab only.
2
The alarm is triggered if someone breaks the
F Switch off the ignition and get out of the vehicle.
windscreen or penetrates the cab.
F Lock the vehicle using the
It is not triggered if someone penetrates the
remote control.
loading area.
or
Volumetric
F Lock the vehicle using the "Smart Entry &
Start System".
System which protects and provides a deterrent
against theft and break-ins.
The system monitors the passenger
The monitoring system is active: the indicator
compartment for any variation in volume.
lamp in the button flashes once per second
The alarm is triggered if someone breaks
Self-protection function
and the direction indicators come on for about
the windscreen, penetrates the passenger
The system checks for the
2 seconds.
compartment or moves around inside the
disconnection of any of its components.
Following a command to lock the vehicle using
vehicle.
The alarm is triggered if the battery,
the remote control or the Smart Entry & Start
the button or the siren wiring is
System, the exterior perimeter monitoring is
disconnected or damaged.
activated after a delay of 5 seconds, the interior
If your vehicle is fitted with the fuel
volumetric monitoring after 45 seconds.
For all work on the alarm system,
burner heater / remote controlled fuel
If an opening (door, rear tailgate or rear wing
contact an authorized Toyota dealer or
burner heater, volumetric monitoring is
doors with glass windows, bonnet...) is not
repairer, or another duly qualified and
not compatible with this system.
closed fully, the vehicle is not locked but
equipped professional.
For more information on Fuel
monitoring will be activated after a delay of
burner heater / Remote controlled
45 seconds.
fuel burner heater, refer to the
Exterior perimeter
corresponding section.
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open
one of the doors or the bonnet.
95
Access
Deactivation
Volumetric monitoring
F Reactivate the full alarm system
by locking the vehicle using the
F Press this unlocking button on
Deactivation
remote control or the "Smart
the remote control.
Entry & Start System".
F Switch off the ignition and within
ten seconds press this button
or
until its indicator lamp is on fixed.
The indicator lamp in the button flashes once
F Unlock the vehicle using the "Smart
per second again.
Entry & Start System".
F Get out of the vehicle.
The monitoring system is deactivated: the
indicator lamp in the button is off and the
F Immediately lock the vehicle
direction indicators flash for about 2 seconds.
using the remote control or the
"Smart Entry & Start System".
Triggering of the alarm
This is indicated by sounding of the siren
and flashing of the direction indicators for
If the vehicle locks itself automatically
Only the exterior perimeter protection system is
thirty seconds.
(this occurs after 30 seconds if one of
active: the indicator lamp in the button flashes
The monitoring functions remain active until
the doors is not opened), the monitoring
once per second.
the alarm has been triggered eleven times in
system is reactivated automatically.
To be effective, this deactivation must be done
succession.
every time the ignition is switched off.
When the vehicle is unlocked using
the remote control or the "Smart
Protection - exterior
Entry & Start System", rapid flashing
perimeter monitoring only
of the indicator lamp in the button
Reactivation
Deactivate the interior volumetric monitoring
informs you that the alarm was
to avoid unwanted triggering of the alarm in
triggered during your absence.
F Deactivate the exterior perimeter
certain cases such as:
When the ignition is switched on, this
monitoring by unlocking the
-
occupant(s) present in the vehicle,
flashing stops immediately.
vehicle using the remote control
-
leaving a window partially open,
or the "Smart Entry & Start
-
washing your vehicle,
System".
-
changing a wheel,
The indicator lamp in the button goes off.
-
towing your vehicle,
-
transport on a ferry.
96
Access
Failure of the remote control
Operating fault
To deactivate the monitoring functions:
When the ignition is switched on,
F Unlock the vehicle using the key (integral
fixed illumination of the indicator
with the remote control with Smart Entry &
lamp in the button indicates a fault in
2
Start System) in the driver's door lock.
the system.
F Open the door; the alarm is triggered.
Have it checked by an authorized
F Switch on the ignition; the alarm stops. The
Toyota dealer or repairer, or
indicator lamp in the button goes off.
another duly qualified and equipped
professional.
Automatic activation
This function is either not available, an option
Locking the vehicle without
or is standard.
activating the alarm
2 minutes after the last opening (door or boot)
F Lock or deadlock the vehicle using the key
is closed, the system is activated automatically.
(integral with the remote control with Smart
Entry & Start System) in the driver's door
F To avoid triggering the alarm on entering
lock.
the vehicle, first press the unlocking button
on the remote control or unlock the vehicle
using the "Smart Entry & Start System".
97
Access
Reinitialisation
Electric windows
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
Automatic mode
F
Lower the window fully, then raise it, it will
Press or pull the control, beyond the point
rise in steps of a few centimetres each time
of resistance. The window opens or closes
the control is pressed.
fully when the control is released. Pressing
F
Repeat the operation until the window is
the control again stops the movement of the
fully closed.
window.
F
Continue to pull the control up for at least
The electrical functions of the electric windows
one second after the window closed
are deactivated:
position has been reached.
-
approximately 45 seconds after the ignition
The safety anti-pinch function does not
is switched off,
operate during these operations.
-
after one of the front doors is opened, if the
1.
Driver's electric window control
ignition is off.
2.
Passenger electric window control
Always remove the key when leaving
the vehicle, even for a short period.
If an electric window meets an obstacle
Safety anti-pinch
There are two operating modes:
during operation, you must reverse the
If your vehicle is fitted with the safety anti-pinch
movement of the window. To do this,
function, when the window rises and meets an
press the control concerned.
Manual mode
obstacle, it stops and partially lowers.
When the driver operates the
In the event of unwanted opening of the window
Press or pull the control, without passing the
passenger electric window controls,
on closing, press the control until the window is
point of resistance. The window stops when
they must ensure that no one is
fully open. Within the next 4 seconds, pull the
you release the control.
preventing the correct closing of the
control until the window is fully closed.
windows.
The safety anti-pinch function does not operate
The driver must ensure that passengers
during these operations.
use the electric windows correctly.
Be aware of children when operating
the windows.
98
Ease of use and comfort
Steering wheel adjustment
Front seats with manual adjustments
As a safety measure, seat adjustments should only be carried out when stationary.
Forwards-backwards
Height
3
F When stationary, lower the control lever
to release the steering wheel adjustment
mechanism.
F Adjust the height and reach to suit your
driving position.
F Pull the control lever to lock the steering
wheel adjustment mechanism.
As a safety precaution, these
F Raise the control and slide the seat
F If fitted to your vehicle, pull the control
operations should only be carried out
forwards or backwards.
upwards to raise or push it downwards to
while the vehicle is stationary.
lower, as many times as required to obtain
For more information on the Seat belts,
the position required.
refer to the corresponding section.
Before moving the seat backwards, ensure that there is nothing that might prevent the full
travel of the seat, so as to avoid the risk of jamming the seat caused by the presence of
objects on the floor behind the seat or rear passengers. If the seat jams, stop the movement
immediately.
99
Ease of use and comfort
Backrest angle
Lumbar
F Turn the knob to adjust the backrest.
F Pull the control fully up and move the
F Turn the knob manually to obtain the
backrest forward or backward.
desired level of lumbar support.
100
Ease of use and comfort
Table position for the
driver's and/or the
front passenger's seat
backrest
On the front passenger's side, this position
allows long objects to be carried.
On the driver's side, this position allows rear
3
passengers to be helped out of the vehicle (by
the emergency services).
Check that there is no object that could
interfere with the movement of a seat,
both above and below.
F Place the head restraint in the low position,
F Pull the control fully up and tip the backrest
and if fitted to your vehicle, raise the
forward.
armrest and fold the table on the back of
To return to the normal position, pull the
the seat.
control up to release the backrest, then pull the
backrest up to its raised position.
101
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст