Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 220
EXTERIOR – ACCESS DOOR BLACK OUT TAPE
ET–109
ET
REMOVAL
HINT:
The procedure described below is for the LH side. Use the
same procedure for both the RH and LH sides, unless
otherwise specified.
1.
REMOVE ACCESS PANEL REAR WEATHERSTRIP
HINT:
Use the same procedure as for the RH side (See page
).
2.
REMOVE LAP BELT OUTER ANCHOR COVER
HINT:
Use the same procedure as for the RH side (See page
).
3.
REMOVE ACCESS DOOR INSIDE HANDLE SUB-
ASSEMBLY
HINT:
Use the same procedure as for the RH side (See page
).
4.
REMOVE CUP HOLDER
HINT:
Use the same procedure as for the RH side (See page
).
5.
REMOVE ACCESS DOOR TRIM BOARD SUB-
ASSEMBLY
HINT:
Use the same procedure as for the RH side (See page
).
6.
REMOVE CENTER PILLAR UPPER GARNISH
HINT:
Use the same procedure as for the RH side (See page
).
7.
REMOVE ACCESS DOOR OPENING TRIM
HINT:
Use the same procedure as for the RH side (See page
).
8.
REMOVE ACCESS PANEL WEATHERSTRIP
HINT:
Use the same procedure as for the RH side (See page
).
9.
REMOVE ACCESS DOOR GLASS OUTER
WEATHERSTRIP (See page
10. REMOVE ACCESS DOOR GLASS SUB-ASSEMBLY
ET–110
EXTERIOR – ACCESS DOOR BLACK OUT TAPE
ET
11. REMOVE NO. 4 BLACK OUT TAPE
(a) Using an infrared light, heat the No. 4 black out
tape.
CAUTION:
Do not burn yourself with the heated front door
panel or infrared light.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 3 to 5 minutes.
(b) Lift the end portion with your nail and peel it parallel
to the attachment surface.
12. REMOVE NO. 6 BLACK OUT TAPE
(a) Using an infrared light, heat the No. 6 black out
tape.
CAUTION:
Do not burn yourself with the heated front door
panel or infrared light.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 3 to 5 minutes.
(b) Lift the end portion with your nail and peel it parallel
to the attachment surface.
13. REMOVE NO. 5 BLACK OUT TAPE
(a) Using an infrared light, heat the No. 6 black out
tape.
CAUTION:
Do not burn yourself with the heated front door
panel or infrared light.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 3 to 5 minutes.
(b) Lift the end portion with your nail and peel it parallel
to the attachment surface.
B135194
B135196
B135198
EXTERIOR – ACCESS DOOR BLACK OUT TAPE
ET–111
ET
INSTALLATION
HINT:
The procedure described below is for the LH side. Use the
same procedure for both the RH and LH sides, unless
otherwise specified.
1.
INSTALL NO. 5 BLACK OUT TAPE
(a) Application precautions (See page
(b) Clean the attachment surface (Using an infrared
).
(c) Clean the attachment surface (Using a tape removal
disc) (See page
).
(d) Apply new No. 5 black out tape to the positions
shown in the illustration.
Installation position:
2.
INSTALL NO. 6 BLACK OUT TAPE
(a) Application precautions (See page
(b) Clean the attachment surface (Using an infrared
).
(c) Clean the attachment surface (Using a tape removal
disc) (See page
).
A
A
a
Unnecessary Portion
Unnecessary Portion
B135199E01
Mark
Measurement
a
2 to 4 mm (0.079 to 0.157 in.)
ET–112
EXTERIOR – ACCESS DOOR BLACK OUT TAPE
ET
(d) Apply new No. 6 black out tape to the positions
shown in the illustration.
Installation position:
3.
INSTALL NO. 4 BLACK OUT TAPE
(a) Application precautions (See page
).
(b) Clean the attachment surface (Using an infrared
light) (See page
(c) Clean the attachment surface (Using a tape removal
disc) (See page
(d) Apply new No. 4 black out tape to the positions
shown in the illustration.
Installation position:
4.
INSTALL ACCESS DOOR GLASS SUB-ASSEMBLY
(See page
)
A
A
B
B
a
b
Unnecessary
Portion
B135197E01
Mark
Measurement
a
2 to 4 mm (0.079 to 0.157 in.)
b
2 mm (0.079 in.)
A
A
B
B
a
b
Unnecessary
Portion
B135195E01
Mark
Measurement
a
10 mm (0.394 in.)
b
2 mm (0.079 in.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст