Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 221
EXTERIOR – ACCESS DOOR BLACK OUT TAPE
ET–113
ET
5.
INSTALL ACCESS DOOR GLASS OUTER
WEATHERSTRIP (See page
6.
INSTALL ACCESS PANEL WEATHERSTRIP
HINT:
Use the same procedure as for the RH side (See page
).
7.
INSTALL ACCESS DOOR OPENING TRIM
HINT:
Use the same procedure as for the RH side (See page
).
8.
INSTALL CENTER PILLAR UPPER GARNISH
HINT:
Use the same procedure as for the RH side (See page
).
9.
INSTALL ACCESS DOOR TRIM BOARD SUB-
ASSEMBLY
HINT:
Use the same procedure as for the RH side (See page
).
10. INSTALL CUP HOLDER
HINT:
Use the same procedure as for the RH side (See page
).
11. INSTALL ACCESS DOOR INSIDE HANDLE SUB-
ASSEMBLY
HINT:
Use the same procedure as for the RH side (See page
).
12. INSTALL LAP BELT OUTER ANCHOR COVER
HINT:
Use the same procedure as for the RH side (See page
).
13. INSTALL ACCESS PANEL REAR WEATHERSTRIP
HINT:
Use the same procedure as for the RH side (See page
).
1GR-FE FUEL – FUEL SYSTEM
FU–1
FU
FUEL SYSTEM
PRECAUTION
1.
BEFORE WORKING ON FUEL SYSTEM
(a) Before working on the fuel system, disconnect the
cable from the negative battery terminal.
(b) Do not work on the fuel system near naked flames.
Never smoke during the work.
(c) Keep rubber and leather parts away from gasoline.
2.
DISCHARGE FUEL SYSTEM PRESSURE
CAUTION:
•
DISCHARGE FUEL SYSTEM PRESSURE
procedures must be performed before
disconnecting any part of the fuel system.
•
As some pressure remains in the fuel line even
after taking precautions to prevent gasoline
spillage, use a shop rag or piece of cloth to
prevent gasoline splashes when disconnecting
the fuel line.
(a) Disconnect the cable from the negative battery
terminal.
(b) Remove the circuit opening relay (see page
).
(c) Connect the cable to the battery negative terminal.
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
(d) Start the engine.
(e) Turn the ignition switch to ON after the engine
stops.
HINT:
DTC P0171 (system too lean (Bank 1)) or DTC
P0174 (system too learn (Bank 2)) may be set.
(f)
Crank the engine again and check that the engine
stops.
(g) Remove the fuel tank cap and discharge the
pressure in the fuel tank completely.
(h) Install the circuit opening relay (see page
).
3.
FUEL SYSTEM
(a) When disconnecting the high-pressure fuel line, a
large amount of gasoline will splash. So take the
following precautions.
(1) Discharge the fuel system pressure.
(2) Disconnect the fuel tank main tube (see page
(3) Drain the fuel remaining in the fuel tank main
tube.
(4) Cover the disconnected fuel tank main tube (fuel
tube joint and fuel tube connector) with a vinyl
bag to prevent damage and the intrusion of
foreign objects.
FU–2
1GR-FE FUEL – FUEL SYSTEM
FU
(b) Take the following precautions when installing the
fuel injector.
(1) Do not reuse the O-ring.
(2) Do not damage a new O-ring when installing it
into the fuel injector.
(3) Before installing a new O-ring, apply gasoline or
spindle oil.
NOTICE:
Do not use engine oil, gear oil or brake oil.
(4) Install the fuel injector into the fuel delivery pipe
and cylinder head as illustrated.
NOTICE:
Apply gasoline or spindle oil to the contact
surface of the fuel delivery pipe and fuel
injector before installing the fuel injector.
(c) Take the following precautions when disconnecting
the fuel tube connector.
HINT:
The structure of the fuel tube connector is as shown
in the illustration.
(1) Check the fuel tube connector and pipe for dirt
and mud before removing the fuel tube
connector.
If dirty, wipe it with a shop rag or piece of cloth.
(2) Pinch the retainer as illustrated, and pull the fuel
tube connector out of the pipe.
(3) If the fuel tube connector and pipe are stuck,
pinch the pipe, then push and pull the fuel tube
connector to release and disconnect it.
NOTICE:
Never use any tools.
(4) After removing the fuel tube, check the sealing
surface of the pipe for dirt and mud.
If dirty, wipe it with a shop rag or piece of cloth.
(5) Cover the disconnected fuel tube connector and
pipe with a vinyl bag to prevent damage and the
intrusion of foreign objects.
CORRECT
WRONG
O-ring
Delivery Pipe
A075945E04
Delivery Pipe
Intake
Manifold
O-ring
Injector
Insulator
A075911E05
Pipe
Retainer
Nylon Tube
Fuel Tube Connector
O-ring
A098610E09
Retainer
Pinch
Pinch
Pull Out
A088336E15
A088337E01
1GR-FE FUEL – FUEL SYSTEM
FU–3
FU
(d) Take the following precautions when installing the
fuel tube connector.
(1) Align the fuel tube connector with the pipe, then
push in the fuel tube connector until the retainer
makes a "click" sound.
(2) After connecting the fuel tube connector, check
that the fuel tube connector and pipe are
securely connected by pulling them.
Push
A088339E03
Pull
A088340E02
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст