Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 241
INSTRUMENT PANEL – INSTRUMENT PANEL ASSEMBLY
IP–7
IP
ACCESSORY
METER ASSEMBLY
ACCESSORY
METER
BRACKET
LOWER INSTRUMENT
PANEL SUB-ASSEMBLY LH
METER
COVER
NO. 2 INSTRUMENT
PANEL BOX DOOR
SUB-ASSEMBLY
INSTRUMENT PANEL CENTER
BRACKET SUB-ASSEMBLY
GLOVE COMPARTMENT DOOR
STOPPER SUB-ASSEMBLY
INSTRUMENT CLUSTER LOWER CENTER
FINISH PANEL SUB-ASSEMBLY
INSTRUMENT CLUSTER CENTER
FINISH PANEL SUB-ASSEMBLY
LOWER INSTRUMENT
PANEL SUB-ASSEMBLY RH
INSTRUMENT PANEL
CLIP
w/ Accessory Meter:
INSTRUMENT
CLUSTER
FINISH PANEL
SUB-ASSEMBLY
<B>
<B>
<B>
<B>
<B>
<B>
<B>
<B>
<B>
<B>
<H>
B133848E01
IP–8
INSTRUMENT PANEL – INSTRUMENT PANEL ASSEMBLY
IP
DEFROSTER NOZZLE
ASSEMBLY
FRONT PASSENGER
AIRBAG ASSEMBLY
NO. 1 SIDE DEFROSTER
NOZZLE DUCT
NO. 2 INSTRUMENT
PANEL WIRE
NO. 2 SIDE DEFROSTER
NOZZLE DUCT
NO. 3 HEATER TO REGISTER DUCT
<B>
<B>
<B>
<B>
<B>
<B>
<B>
<B>
<B>
B133849E01
INSTRUMENT PANEL – INSTRUMENT PANEL ASSEMBLY
IP–9
IP
REMOVAL
HINT:
Use the same procedure for both the RH and LH sides.
1.
BOLTS, SCREWS AND NUTS TABLE
HINT:
All bolts, screws and nuts relevant to installing and
removing the instrument panel are shown, along with
their alphabetic codes, in the table below.
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for at least 90 seconds after disconnecting the
cable to prevent the airbag from working.
3.
REMOVE FRONT DOOR SCUFF PLATE RH (See page
4.
REMOVE FRONT DOOR SCUFF PLATE LH (See page
5.
REMOVE FRONT FLOOR FOOTREST (See page
)
6.
REMOVE FOOTREST CLIP (See page
)
φ = 6
(0.24)
L = 14
(0.55)
Code
Shape
φ = 6
(0.24)
L = 20
(0.79)
φ = 6
(0.24)
L = 20
(0.79)
φ = 5
(0.20)
L = 14
(0.55)
φ = 5
(0.20)
L = 14
(0.55)
φ = 6
(0.24)
Code
Shape
Code
Shape
φ = 6
(0.24)
L = 20
(0.79)
<A>
<D>
<G>
<B>
<E>
<C>
<F>
mm (in.) (L = Length)
φ = 5
(0.20)
L = 18
(0.71)
<H>
B133850E01
IP–10
INSTRUMENT PANEL – INSTRUMENT PANEL ASSEMBLY
IP
7.
REMOVE COWL SIDE TRIM BOARD RH (See page
)
8.
REMOVE COWL SIDE TRIM BOARD LH (See page
)
9.
SEPARATE FRONT DOOR OPENING TRIM
WEATHERSTRIP LH
(a) Separate the front door opening trim weatherstrip
LH.
10. SEPARATE FRONT DOOR OPENING TRIM
WEATHERSTRIP RH
(a) Separate the front door opening trim weatherstrip
RH.
11. REMOVE ASSIST GRIP PLUG (See page
12. REMOVE ASSIST GRIP ASSEMBLY (See page
13. REMOVE FRONT PILLAR GARNISH RH (See page
)
14. REMOVE FRONT PILLAR GARNISH LH (See page
)
15. REMOVE INSTRUMENT PANEL GARNISH LH
(a) Remove screw <H>.
(b) Disengage the 3 clips and remove the instrument
panel garnish.
NOTICE:
•
Pull the instrument panel garnish up at an
angle of 45
° to remove it.
•
Do not damage the surface of the instrument
panel when removing it.
16. REMOVE INSTRUMENT PANEL GARNISH RH
(a) Remove screw <H>.
(b) Disengage the 3 clips and remove the instrument
panel garnish.
NOTICE:
•
Pull the instrument panel garnish up at an
angle of 45
° to remove it.
•
Do not damage the surface of the instrument
panel when removing it.
B133886
B133887
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст