Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 292
LIGHTING – LIGHTING SYSTEM
LI–65
LI
OK
(a) Remove the TAIL relay from the main body ECU.
(b) Measure the resistance.
Standard resistance
(c) Reinstall the TAIL relay.
NG
OK
(a) Remove the front turn signal lights.
(b) Apply battery voltage to the terminals and check that the
front turn signal light illuminates.
Standard
(c) Reinstall the front turn signal lights.
NG
OK
4
CHECK HARNESS AND CONNECTOR (BATTERY - TAIL RELAY)
Component Side:
Main Body ECU
B138193E01
Tester Connection
Condition
Specified Condition
1 - Body ground
Always
11 to 14 V
5 - Body ground
Always
11 to 14 V
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPLACE MAIN BODY ECU
5
INSPECT BULB (FRONT TURN SIGNAL LIGHT)
Component Side:
Front Turn Signal Light*
*: LH or RH
B136088E01
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Front turn signal light illuminates
REPLACE BULB
LI–66
LIGHTING – LIGHTING SYSTEM
LI
(a) Disconnect the A16 and A20 front turn signal light
connectors.
(b) Disconnect the 1B main body ECU connector.
(c) Measure the resistance.
Standard resistance
(d) Reconnect the front turn signal light connectors.
(e) Reconnect the main body ECU connector.
NG
OK
(a) Remove the taillights.
(b) Apply battery voltage to the terminals and check that the
taillight illuminates.
Standard
(c) Reinstall the taillights.
NG
OK
6
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT TURN SIGNAL LIGHT)
1
2
3
4
5
6
7
8
9 10 11 12 13
1B
A16
A20
Wire Harness Side:
Front View
Front View
Main Body ECU Connector
*1: LH
*2: RH
Front Turn Signal Light Connector
*
1
*
2
B138191E01
Tester Connection
Specified Condition
A16-1 - 1B-9
Below 1
Ω
A20-1 - 1B-11
Below 1
Ω
A16-1 or 1B-9 - Body ground
10 k
Ω or higher
A20-1 or 1B-11 - Body ground
10 k
Ω or higher
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT TURN SIGNAL LIGHT - BODY
GROUND)
7
INSPECT BULB (TAILLIGHT)
1
2
3
Component Side:
*: LH or RH
Taillight*
B141038E01
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Taillight illuminates
REPLACE BULB
LIGHTING – LIGHTING SYSTEM
LI–67
LI
(a) Remove the license plate light.
(b) Apply battery voltage to the terminals and check that the
license plate light illuminates.
Standard
(c) Reinstall the license plate light.
NG
OK
(a) Disconnect the L11 and L14 taillight connectors.
(b) Disconnect the S1 license plate light connector.
(c) Disconnect the 1F main body ECU connector.
(d) Measure the resistance.
Standard resistance
(e) Reconnect the taillight connectors.
(f)
Reconnect the license plate light connector.
(g) Reconnect the main body ECU connector.
NG
OK
8
INSPECT BULB (LICENSE PLATE LIGHT)
Component Side:
License Plate Light
B138194E01
Measurement Condition
Standard
Positive battery - Terminal 1
Negative battery - Terminal 2
Licence plate light illuminates
REPLACE BULB
9
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - TAILLIGHT, LICENSE PLATE
LIGHT)
1
2
1
2
3
1
2
3
4
5
6
9
10
11
12
13
14
7
8
15
16
1F
S1
L11
L14
Wire Harness Side:
Front View
Taillight Connector
Front View
License Plate Light Connector
*1: LH
*2: RH
*
1
*
2
Main Body ECU Connector
B138195E01
Tester Connection
Specified Condition
1F-13 - L11-2
Below 1
Ω
1F-13 - L14-2
Below 1
Ω
1F-13 - S1-2
Below 1
Ω
1F-13 or L11-2 or Body ground
10 k
Ω or higher
1F-13 or L14-2 or Body ground
10 k
Ω or higher
1F-13 or S1-2 or Body ground
10 k
Ω or higher
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPAIR OR REPLACE HARNESS OR CONNECTOR (TAILLIGHT, LICENSE PLATE LIGHT - BODY
GROUND)
LI–68
LIGHTING – LIGHTING SYSTEM
LI
(a) Remove the outer rear view mirror assembly.
(b) Apply battery voltage to the terminals and check that the
outer rear view mirror illumination light illuminates.
Standard
(c) Reinstall the outer rear view mirror assembly.
NG
OK
(a) Disconnect the H2 and G2 outer rear view mirror
assembly connectors.
(b) Disconnect the 1L main body ECU connector.
(c) Measure the resistance.
Standard resistance
(d) Reconnect the outer rear view mirror assembly
connector.
(e) Reconnect the main body ECU connector.
NG
OK
10
INSPECT BULB (OUTER REAR VIEW MIRROR ILLUMINATION LIGHT)
1
2
3
4
5
Component Side:
Outer Rear View Mirror Assembly*
*: LH and RH
B138196E01
Measurement Condition
Standard
Positive battery - Terminal 2
Negative battery - Terminal 1
Outer rear view mirror illumination
light illuminates
REPLACE BULB
11
CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - OUTER REAR VIEW MIRROR
ILLUMINATION LIGHT)
1
2
3
4
5
1
13
2
14
3
15
4
16
5
17
6
18
9
21
10
22
11
23
12
24
7
19
8
20
1L
H2
G2
Wire Harness Side:
Front View
*1: LH
*2: RH
Front View
Outer Rear View Mirror Assembly
Connector
*
1
*
2
Main Body ECU Connector
B138197E01
Tester Connection
Specified Condition
1L-5 - H2-2
Below 1
Ω
1L-5 - G2-2
Below 1
Ω
REPAIR OR REPLACE HARNESS OR
CONNECTOR
REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER REAR VIEW MIRROR ILLUMINATION
LIGHT - BODY GROUND)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст