Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 325
ME–32
METER – METER / GAUGE SYSTEM
ME
*1: for M/T
*2: for A/T
*3: w/ Daytime Running Light
*4: w/o Daytime Running Light
*5: for 2WD
*6: w/ Cruise Control
*7: w/ Active Traction Control (4WD only)
*8: w/ Rear Differential Lock
METER – METER / GAUGE SYSTEM
ME–33
ME
DATA LIST / ACTIVE TEST
1.
DATA LIST
By reading the DATA LIST displayed on the intelligent
tester, you can check values, including those of the
switches, sensors, actuators without removing any parts.
Reading the DATA LIST as the first step of
troubleshooting is one method of shortening diagnostic
time.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the intelligent tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Operate the intelligent tester according to the
display on the tester screen and select DATA LIST.
ECM:
Item
Measurement Item: Range
(Display)
Normal Condition
Diagnostic Note
Vehicle SPD
Vehicle speed: Minimum: 0 mph
(0km/h), Maximum: 153 mph (255
km/h)
Approximately equal to actual
vehicle speed (When driving)
-
Engine SPD
Engine speed: Minimum: 0 rpm,
Maximum: 16,383 rpm
Approximately equal to actual
engine speed (With engine
running)
-
Coolant Temp.
Coolant temperature: Minimum: -
40
°C (-40°F), Maximum: 140°C
(284
°F)
After warming up: 80
° to 95 °C
(176
°F to 203°F)
If value -40
°C (-40°F) or 140°C
(284
°F), sensor circuit open or
shorted.
ME–34
METER – METER / GAUGE SYSTEM
ME
ON-VEHICLE INSPECTION
1.
INSPECT SPEEDOMETER
(a) Check the operation.
(1) Using a speedometer tester, inspect the
speedometer and confirm that the
speedometer readings are within the
acceptable range. Also check the odometer
operation.
Reference:
km/h (Canada)
mph (U.S.A.)
NOTICE:
Tire wear and excessively high or low tire
pressure affect speedometer indications.
(2) Check the deflection of the speedometer
indicator.
Reference:
Below 0.3 mph (0.5 km/h)
Standard Indication
Acceptable Range
20 km/h
17.5 to 21.5 km/h
40 km/h
38 to 42 km/h
60 km/h
58 to 63 km/h
80 km/h
78 to 84 km/h
100 km/h
98.5 to 104.5 km/h
120 km/h
119 to 125 km/h
140 km/h
139 to 146 km/h
160 km/h
159 to 167 km/h
180 km/h
179 to 188 km/h
200 km/h
199 to 209 km/h
Standard Indication
Acceptable Range
20 mph
19 to 22 mph
40 mph
39 to 42.5 mph
60 mph
59.5 to 63.5 mph
80 mph
79.5 to 84 mph
100 mph
100 to 105 mph
120 mph
121 to 126.5 mph
METER – METER / GAUGE SYSTEM
ME–35
ME
2.
INSPECT SPEED SENSOR
(a) Check the output signal waveform.
(1) Remove the combination meter assembly, but
do not disconnect the connector.
(2) Connect an oscilloscope to terminal E13-4 and
to the body ground.
(3) Start the engine.
(4) Check the signal waveform according to the
conditions in the table below.
OK:
As shown in the illustration.
NOTICE:
As the vehicle speed increases, the cycle of
the signal waveform narrows.
(5) Reinstall the combination meter assembly.
3.
INSPECT TACHOMETER
(a) Check the operation.
(1) Connect the tune-up test tachometer and start
the engine.
NOTICE:
•
Reversing the connection of the
tachometer will damage the transistors
and the insides of the diodes.
•
When removing or installing the
tachometer, be careful not to drop or
strike it.
(2) Compare the result of the test with the standard
indication.
DC 13.5 V, at 25
°C (77°F)
Reference
GND
Waveform:
Combination Meter Assembly Connector:
E13
SE
E125403E01
Item
Contents
Terminal Connection
SE (E13-4) and Body Ground
Tool Setting
5V / DIV, 20ms / DIV
Condition
Driving at approximately 12mph (20km / h)
Standard Indication (USA) (RPM)
Standard Indication (CANADA) (r/
min)
Data in ( ) are for reference
Acceptable Range (USA) (RPM)
Acceptable Range (CANADA) (r/min)
Data in ( ) are for reference
700
630 to 770
1,000
(900 to 1,100)
2,000
(1,850 to 2,150)
3,000
2,800 to 3,200
4,000
(3,800 to 4,200)
5,000
4,800 to 5,100
(6,000)
(5,750 to 6,250)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст