Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 321
ME–16
METER – METER / GAUGE SYSTEM
ME
(2) Switch the mode to compass correction mode by
pushing the SET button for about 2 seconds,
until the zone number appears in the outside
temperature display.
HINT:
If no button operations occur for more than 6
seconds while in compass correction mode,
calibration is cancelled and the display returns to
the outside temperature indication. To restart,
perform the procedure from the first step again.
(3) Push the SET button again to change the mode
to turn correction mode.
HINT:
While in correction mode, the indication bars
move as shown in the illustration.
(4) If there is sufficient space to drive the vehicle in
a circle, perform the following procedure:
1. Drive the vehicle in a full circle within 2
minutes, at a vehicle speed of 5mph (8km/h)
or lower, as shown in the illustration.
NOTICE:
•
Do not perform the circling calibration of
the compass in a place where the earth's
magnetic field is subject to interference by
artificial magnetic fields (underground
parking, under a steel tower, between
buildings, roof parking, near a crossing,
near a large vehicle, etc.).
•
During the calibration, do not operate any
electric systems (power window, etc.) as
they may interfere with the calibration.
B133406
B133389
B133390
METER – METER / GAUGE SYSTEM
ME–17
ME
HINT:
•
When the compass display returns to the
outside temperature display, the calibration is
complete.
•
When the circling calibration fails, "Er" is
displayed for about 2 seconds and then the
COMPASS indicator flashes.
•
If the correct direction is not displayed after
driving the vehicle as specified, change the
vehicle location.
•
To cancel the calibration before completion,
push the SET button for about 2 seconds.
(5) If enough space is not available to drive in a
circle, perform the following:
1. Perform a four-point turn within 2 minutes, as
shown in the illustration.
NOTICE:
•
Do not perform the circling calibration of
the compass in a place where the earth's
magnetic field is subject to interference by
artificial magnetic fields (underground
parking, under a steel tower, between
buildings, roof parking, near a crossing,
near a large vehicle, etc.).
•
During the calibration, do not operate any
electric systems (power window, etc.) as
they may interfere with the calibration.
HINT:
•
When the compass display returns to the
outside temperature display, the calibration is
complete.
•
When the circling calibration fails, "Er" is
displayed for about 2 seconds and then the
COMPASS indicator flashes.
•
If the correct direction is not displayed after
driving the vehicle as specified, change the
vehicle location.
•
To cancel the calibration before completion,
push the SET button for about 2 seconds.
(6) Check that the COMPASS indicator is not
blinking and that the compass is displayed
normally.
B133392
B133391
B133392
ME–18
METER – METER / GAUGE SYSTEM
ME
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the causes of the
problem symptom. The potential causes of the symptoms are
listed in order of probability in the "Suspected Area" column
of the table. Check each symptom by checking the suspected
area in the order they are listed. Replace parts as necessary.
MALFUNCTION SYSTEM
METER GAUGES
WARNING/INDICATOR LIGHT
Symptom
Suspected area
See page
Entire combination meter assembly does not operate
Refer to troubleshooting
Operating light control rheostat does not change light
brightness
Refer to troubleshooting
Symptom
Suspected area
See page
Speedometer malfunction
Refer to troubleshooting
Tachometer malfunction
Refer to troubleshooting
Fuel gauge malfunction
Refer to troubleshooting
Engine coolant temperature gauge malfunction
Refer to troubleshooting
Symptom
Suspected area
See page
MIL does not come on
ECM
Wire harness or connector
-
Combination meter assembly
Charge warning light does not come on
Generator (alternator)
ECM
Wire harness or connector
-
Combination meter assembly
Brake warning light does not come on
Brake fluid level warning switch
Parking brake switch assembly
Main body ECU
Wire harness or connector
-
Combination meter assembly
ABS warning light does not come on
Skid Control ECU
Combination meter assembly
Airbag waning light does not come on
Center airbag sensor assembly
Combination meter assembly
Engine oil pressure warning light does not come on
Engine oil pressure switch assembly
-
Wire harness or connector
-
Combination meter assembly
Driver side seat belt warning light does not operate
Front seat inner belt assembly LH
Wire harness or connector
-
Combination meter assembly
Turn indicator light does not come on
Turn signal flasher assembly
Wire harness or connector
-
Combination meter assembly
Beam indicator light does not come on
Headlight dimmer switch
Wire harness or connector
-
Combination meter assembly
MAINT REQD indicator light blinks or remains
illuminated*1
Resetting procedure
Combination meter assembly
METER – METER / GAUGE SYSTEM
ME–19
ME
*1: U.S.A. only
*2: for A/T
*3: w/ cruise control
*4: w/ rear differential lock
*5: for 4WD
*6: for 2WD
BUZZER
Open door warning light does not come on
Door courtesy switch
Main body ECU
Wire harness or connector
-
Combination meter assembly
Fuel level warning light does not come on
Wire harness or connector
-
Combination meter assembly
A/T oil temperature warning light does not come on*2
ECM
Wire harness or connector
-
Combination meter assembly
CRUISE indicator light does not come on*3
ECM
Cruise control main switch
Wire harness or connector
-
Combination meter assembly
Rear differential lock indicator light does not come
on*4
4WD control ECU
Wire harness or connector
-
Combination meter assembly
4WD indicator light does not come on*5
4WD control ECU
Wire harness or connector
-
Combination meter assembly
SLIP indicator light does not come on
Skid Control ECU
Wire harness or connector
-
Combination meter assembly
VSC OFF indicator light does not come on*4
Skid control ECU
Wire harness or connector
-
Combination meter assembly
VSC TRAC warning light does not come on
Skid control ECU
Wire harness or connector
-
Combination meter assembly
AUTO LSD indicator light does not come on*6
Skid control ECU
Wire harness or connector
-
Combination meter assembly
A-TRAC indicator light does not come on*5
Skid control ECU
Wire harness or connector
-
Combination meter assembly
Symptom
Suspected area
See page
Symptom
Suspected area
See page
No buzzers sound
Wire harness or connector
-
Combination meter assembly
Seat belt warning buzzer does not sound
Front seat inner belt assembly
Center airbag sensor assembly
Occupant classification sensor
Wire harness or connector
-
Combination meter assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст