Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 319
ME–8
METER – METER / GAUGE SYSTEM
ME
Generator Assembly
Taillight Relay
Light Control Rheostat
Combination Meter
Battery
Air Conditioner
Amplifier Assembly
Accessory Meter
Assembly
E126875E01
METER – METER / GAUGE SYSTEM
ME–9
ME
SYSTEM DESCRIPTION
1.
METER GAUGE AND WARNING INDICATOR
GAUGE
WARNING / INDICATOR
Item
Signal Description
Speedometer
Indicates vehicle speed based on signals received from speed sensor
(Direct line)
Tachometer
Indicates engine speed based on signals from ECM (Direct line)
ODO / TRIP meter
Calculates accumulated total vehicle travel distance and vehicle travel
distance since trip meter knob pressed
Fuel Gauge
Indicates fuel level in accordance with signals received from fuel
sender gauge (Direct line)
Engine Coolant Temperature Gauge
Indicates engine coolant temperature in accordance with signal from
ECM (Direct line)
Volt Gauge
Indicates vehicle voltage according to voltage from IG terminal (Direct
line)
Item
Signal Description
TURN SIGNAL
Receives turn signal from flasher relay (Direct line)
BEAM
Receives beam signal from headlight dimmer switch (BEAN)
CHARGE
Receives malfunction signal from generator (Direct line)
MIL
Receives malfunction check signal from ECM (Direct line)
DOOR
Open door indicator illuminates when receiving signal from main body
ECU (BEAN)
D BELT
Receives driver seat belt signal (unfastened) from center airbag
sensor assembly (BEAN)
BRAKE
Receives parking brake switch signal from main body ECU (Direct
line) and fluid level warning signal from brake level switch (Direct line)
OIL PRESSURE
Receives malfunction signal from oil pressure switch (Direct line)
MAINT REQD*1
Blinks when about 4,500 miles driven since oil change. Illuminates
when about 5,000 miles driven since oil change.
AIRBAG
Receives malfunction signal from center airbag sensor assembly
(Direct line)
ABS
Receives malfunction signal from skid control ECU (Direct line)
P BELT
Blinks when front passenger seat belt switch ON (unfastened)
FUEL
Receives fuel empty signals from fuel sender gauge.
CRUISE*2
Receives malfunction signal from ECM (Direct line)
AUTO LSD*3
Receives signals from hydraulic brake booster while AUTO LSD is
operating.
VSC TRAC
Receives malfunction signal from skid control ECU (Direct line)
VSC OFF*4
Receives malfunction signal from skid control ECU (Direct line)
SLIP
Receives malfunction signal from skid control ECU (Direct line)
ABS
Receives malfunction signal from skid control ECU (Direct line)
4WD*5
Receives signals from 4WD control ECU while 4WD is operating.
A-TRAC*5
Receives malfunction signal from skid control ECU (Direct line)
REAR DIFF. LOCK*4
Receives signals from 4WD control ECU while Rear Differential Lock
is operating.
ME–10
METER – METER / GAUGE SYSTEM
ME
*1: U.S.A. only
*2: w/ Cruise Control
*3: for 2WD
*4: w/ Rear Differential Lock
*5: for 4WD
Buzzer
Item
Signal Description
Key Reminder
Buzzer ON when ignition switch OFF, key inserted and driver door
open.
Manual Shift Reverse (6MT)
Buzzer ON when ignition switch ON and shift position is reverse.
Seat Belt Warning
Buzzer ON when vehicle speed exceeds 12.4mph (20km/h) and seat
belt unfastened.
METER – METER / GAUGE SYSTEM
ME–11
ME
HOW TO PROCEED WITH
TROUBLESHOOTING
HINT:
•
Use these procedures to troubleshoot the combination
meter.
•
Use an intelligent tester in steps 3 and 5.
NEXT
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery
before proceeding.
NEXT
HINT:
Refer to the Problem Symptoms Table (See page
).
Result
B
A
(a) Terminals of ECU (See page
)
(b) On-vehicle Inspection (See page
)
NEXT
NEXT
1
VEHICLE BROUGHT TO WORKSHOP
2
INSPECT BATTERY VOLTAGE
3
PROBLEM SYMPTOMS TABLE
Result
Proceed to
Fault is not listed in problem
symptoms table
A
Fault is listed in problem symptoms
table
B
Go to step 6
4
OVERALL ANALYSIS AND TROUBLESHOOTING
5
ADJUST, REPAIR OR REPLACE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст