Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 197
EXTERIOR – REAR BUMPER
ET–19
ET
5.
REMOVE REAR BUMPER UPPER RETAINER LH
(a) Remove the 2 screws.
(b) Disengage the 3 claws and remove the rear bumper
upper retainer.
6.
REMOVE REAR BUMPER UPPER RETAINER RH
HINT:
Use the same procedure as for the LH side.
7.
REMOVE REAR BUMPER ENERGY ABSORBER
(a) Disengage the 2 claws and remove the rear bumper
energy absorber.
8.
REMOVE REAR BUMPER SIDE STAY LH
(a) Remove the bolt and the rear bumper side stay.
9.
REMOVE REAR BUMPER SIDE STAY RH
HINT:
Use the same procedure as for the LH side.
10. REMOVE REAR BUMPER SIDE SUPPORT SUB-
ASSEMBLY LH
(a) Remove the 2 bolts and the rear bumper side
support.
11. REMOVE REAR BUMPER SIDE SUPPORT SUB-
ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
12. REMOVE REAR BUMPER BAR BRACKET LH
(a) Remove the bolt and the rear bumper bar bracket.
13. REMOVE REAR BUMPER BAR BRACKET RH
HINT:
Use the same procedure as for the LH side.
B134751
B134752
B138423
B135071
B138424
ET–20
EXTERIOR – REAR BUMPER
ET
DISASSEMBLY
1.
REMOVE FLOOR WIRE (w/ Back Sonar)
HINT:
Use the same procedure for both sides.
(a) Using a clip remover, remove the 3 clamps.
(b) Disconnect the ultrasonic sensor connector and
remove the floor wire.
2.
REMOVE ULTRASONIC SENSOR (w/ Back Sonar)
HINT:
Use the same procedure for both sides.
(a) Remove the retainer and the ultrasonic sensor as
shown in the illustration.
for LH Side:
for RH Side:
B135145E01
for LH Side:
for RH Side:
B135146E01
EXTERIOR – REAR BUMPER
ET–21
ET
3.
REMOVE REAR BUMPER PAD LH
(a) Remove the 5 retainers.
(b) Disengage the 5 claws and remove the rear bumper
pad.
4.
REMOVE REAR BUMPER PAD RH
HINT:
Use the same procedure as for the LH side.
5.
REMOVE REFLEX REFLECTOR ASSEMBLY LH
(a) Remove the nut and the reflex reflector.
6.
REMOVE REFLEX REFLECTOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
7.
REMOVE REAR BUMPER LOWER COVER
(a) Remove the 4 screws.
(b) Disengage the 4 clips and remove the rear bumper
lower cover.
(c) Remove the 4 screw grommets.
B135148
B135149
B135150
B135151
ET–22
EXTERIOR – REAR BUMPER
ET
REASSEMBLY
1.
INSTALL REAR BUMPER LOWER COVER
(a) Install the 4 screw grommets.
(b) Engage the 4 clips and install the rear bumper lower
cover.
(c) Tighten the 4 screws.
Torque: 3.0 N*m (30 kgf*cm, 27 in.*lbf)
2.
INSTALL REFLEX REFLECTOR ASSEMBLY LH
(a) Install the reflex reflector with the nut.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf)
3.
INSTALL REFLEX REFLECTOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
4.
INSTALL REAR BUMPER PAD LH
(a) Engage the 5 claws and install the rear bumper pad.
(b) Install the 5 retainers.
5.
INSTALL REAR BUMPER PAD RH
HINT:
Use the same procedure as for the LH side.
B135151
B135150
B135149
B135148
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст