Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 198
EXTERIOR – REAR BUMPER
ET–23
ET
6.
INSTALL ULTRASONIC SENSOR (w/ Back Sonar)
HINT:
Use the same procedure for both sides.
(a) Install the ultrasonic sensor with the retainer as
shown in the illustration.
7.
INSTALL FLOOR WIRE (w/ Back Sonar)
HINT:
Use same procedure for both sides.
(a) Connect the ultrasonic sensor connector.
(b) Install the floor wire with the 3 clamps.
INSTALLATION
1.
INSTALL REAR BUMPER BAR BRACKET LH
(a) Insert the hook into the body hole and install the
rear bumper bar bracket with the bolt.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf)
2.
INSTALL REAR BUMPER BAR BRACKET RH
HINT:
Use the same procedure as for the LH side.
for LH Side:
for RH Side:
B135152E01
for LH Side:
for RH Side:
B135145E01
B134754
ET–24
EXTERIOR – REAR BUMPER
ET
3.
INSTALL REAR BUMPER SIDE SUPPORT SUB-
ASSEMBLY LH
(a) Align the locating pin with the hole and install the
rear bumper side support with the 2 bolts.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf)
4.
INSTALL REAR BUMPER SIDE SUPPORT SUB-
ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
5.
INSTALL REAR BUMPER SIDE STAY LH
(a) Insert the hook into the body hole and install the
rear bumper side stay with the bolt.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf)
6.
INSTALL REAR BUMPER SIDE STAY RH
HINT:
Use the same procedure as for the LH side.
7.
INSTALL REAR BUMPER ENERGY ABSORBER
(a) Engage the 2 claws and install the rear bumper
energy absorber.
8.
INSTALL REAR BUMPER UPPER RETAINER LH
(a) Engage the 3 claws and install the rear bumper
upper retainer.
(b) Tighten the 2 screws.
Torque: 3.0 N*m (30 kgf*cm, 27 in.*lbf)
9.
INSTALL REAR BUMPER UPPER RETAINER RH
HINT:
Use the same procedure as for the LH side.
10. INSTALL REAR BUMPER END RETAINER LH
(a) Engage the 2 claws and install the rear bumper end
retainer.
(b) Tighten the screw.
Torque: 3.0 N*m (30 kgf*cm, 27 in.*lbf)
11. INSTALL REAR BUMPER END RETAINER RH
HINT:
Use the same procedure as for the LH side.
B135072
B134753
B134752
B134751
B134750
EXTERIOR – REAR BUMPER
ET–25
ET
12. INSTALL REAR BUMPER COVER
(a) Engage the 6 claws and the 2 clips and install the
rear bumper cover.
(b) w/ Back Sonar:
(1) Connect the 2 wire to wire connectors.
B135143
B135142
ET–26
EXTERIOR – REAR BUMPER
ET
(c) Tighten the 7 bolts and the 2 screws.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf) for bolt
3.0 N*m (30 kgf*cm, 27 in.*lbf) for screw
(d) Remove the protective tape.
13. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
B135141
B135140
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст