Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 1
DOOR LOCK – BACK DOOR LOCK
DL–117
DL
(b) Remove the back door lock cylinder.
INSPECTION
1.
INSPECT BACK DOOR LOCK
(a) Check the operation of the back door lock actuator.
(1) Apply battery voltage to the back door lock
actuator and check the operation of the back
door lock motor.
Standard
If the result is not as specified, replace the back
door lock.
(b) Check the resistance of the door lock and unlock
switch.
(1) Using an ohmmeter, measure the resistance
and check the results in accordance with the
value(s) in the table below.
Standard Resistance
If the result is not as specified, replace the back
door lock.
2.
INSPECT BACK DOOR LOCK CYLINDER
(a) Check the resistance.
(1) Using an ohmmeter, measure the resistance
between the terminals when the cylinder is
operated with a key.
Standard Resistance
If the result is not as specified, replace the back
door lock cylinder.
B135548
Lock
Unlock
B135520E02
Measurement Condition
Specified Condition
Battery positive (+)
→ Terminal 2
Battery negative (-)
→ Terminal 1
Unlocks
Battery positive (+)
→ Terminal 1
Battery negative (-)
→ Terminal 2
Locks
Tester Connection
Door Lock Condition
Specified Condition
4 - 5
Unlocked
Below 1
Ω
4 - 5
Locked
10 k
Ω or higher
4 - 6
Unlocked
10 k
Ω or higher
4 - 6
Locked
Below 1
Ω
Unlock
Lock
B140025E01
Tester Connection
Condition
Specified Condition
1 - 2
Locked
Below 1
Ω
1 - 2
Unlocked
10 k
Ω or higher
1 - 3
Locked
10 k
Ω or higher
1 - 3
Unlocked
Below 1
Ω
DL–118
DOOR LOCK – BACK DOOR LOCK
DL
INSTALLATION
1.
INSTALL BACK DOOR LOCK
(a) Apply MP grease to the sliding and rotating areas of
the back door lock.
(b) Using "Torx" socket wrench T30, install the back
door lock with the 3 screws.
Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
(c) Tighten bolt A.
Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
(d) Connect the connector.
(e) Connect the back door lock rod as shown in the
illustration.
2.
INSTALL BACK DOOR LOCK CYLINDER
(a) Install the back door lock cylinder.
(b) Install the retainer, then connect the 2 clamps.
3.
INSTALL BACK DOOR SERVICE HOLE COVER (See
page
)
4.
INSTALL BACK DOOR TRIM BOARD (See page
)
5.
INSTALL DOOR TRIM RETAINER CAP (See page
)
6.
INSTALL BACK DOOR TRIM COVER RH (See page
7.
INSTALL BACK DOOR TRIM COVER LH
HINT:
Use the same procedure as for the RH side.
8.
CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
A
B135519E01
B135518
B135548
B135547
DOOR LOCK – WIRELESS DOOR LOCK BUZZER
DL–119
DL
BODY ELECTRICAL
DOOR LOCK
WIRELESS DOOR LOCK BUZZER
COMPONENTS
FRONT FENDER SPLASH SHIELD
SUB-ASSEMBLY
NO. 1 WIRING HARNESS
PROTECTOR
WIRELESS DOOR
LOCK BUZZER
x5
B138140E01
DL–120
DOOR LOCK – WIRELESS DOOR LOCK BUZZER
DL
REMOVAL
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2.
REMOVE FRONT FENDER SPLASH SHIELD SUB-
ASSEMBLY
(a) Disengage the 6 clips.
(b) Disengage the 3 clips and remove the front fender
splash shield.
3.
REMOVE NO. 1 WIRING HARNESS PROTECTOR
(a) Disengage the 4 claws and remove the No. 1 wiring
harness protector.
4.
REMOVE WIRELESS DOOR LOCK BUZZER
(a) Disengage the clamp of the wireless door lock
buzzer.
B136004
B138136
B138137
B138138
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст