Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 456
SE–6
SEAT – FRONT SEAT ASSEMBLY
SE
(c) Lift up on the area where the claw was removed.
Then push in the direction of the claw on the
opposite side to remove the outside claw.
(d) After the 2 claws have been removed, carefully pull
the front seat track cover rearward and remove the
front seat track cover.
3.
REMOVE FRONT SEAT ASSEMBLY
(a) for Driver Side:
(1) Using a clip remover, remove the clamp.
(2) Disconnect the 2 buckle switch connectors.
(3) w/ Front Seat Side Airbag:
1. Slide the slider and disconnect the airbag
connector.
Push
A-A
A
A
1 Push
2 Up
B138596E01
Pull
B138597E01
Slider
B135117E01
SEAT – FRONT SEAT ASSEMBLY
SE–7
SE
(b) for Front Passenger Side:
(1) Using a clip remover, remove the clamp.
(2) Disconnect the connector.
(3) w/ Front Seat Side Airbag:
1. Slide the slider and disconnect the airbag
connector.
(c) Move the front seat to the most forward position.
(d) Remove the 2 bolts from the rear side.
(e) Move the front seat to the most rearward position.
(f)
Remove the 2 bolts fromthe front side.
(g) Remove the front seat.
Slider
B135119E01
B130665
SE–8
SEAT – FRONT SEAT ASSEMBLY
SE
DISASSEMBLY
CAUTION:
Wear protective gloves. Sharp surfaces on the front seat
adjuster could cause injuries to your hands.
HINT:
The procedure described below is for the driver side. Use the
same procedure for both the driver and front passenger
sides, unless otherwise specified.
1.
REMOVE VERTICAL SEAT ADJUSTER KNOB (for
Driver Side)
(a) Using a screwdriver with its tip wrapped in
protective tape, disengage the snap ring and
remove the vertical seat adjuster knob.
2.
REMOVE VERTICAL SEAT ADJUSTER HANDLE
COVER (for Driver Side)
(a) Using a screwdriver with its tip wrapped in
protective tape, disengage the 3 claws and remove
the vertical seat adjuster handle cover.
3.
REMOVE VERTICAL SEAT ADJUSTER HANDLE (for
Driver Side)
(a) Remove the 2 screws and the vertical seat adjuster
handle.
4.
REMOVE RECLINING ADJUSTER RELEASE
HANDLE
(a) Using a screwdriver with its tip wrapped in
protective tape, disengage the claw and remove the
reclining adjuster release handle.
Protective Tape
B130668E01
Protective Tape
B130670E01
B130672
Protective Tape
B130673E01
SEAT – FRONT SEAT ASSEMBLY
SE–9
SE
5.
REMOVE FRONT SEAT CUSHION OUTER SHIELD
(a) Remove the screw.
(b) Using a screwdriver with its tip wrapped in
protective tape, disengage the 2 claws and the clip
and remove the front seat cushion outer shield.
6.
REMOVE FRONT SEAT INNER BELT ASSEMBLY
(See page
)
7.
REMOVE FRONT SEAT CUSHION INNER SHIELD
(a) Remove the screw.
(b) Using a screwdriver with its tip wrapped in
protective tape, disengage the claw and the clip and
remove the front seat cushion inner shield.
8.
REMOVE FRONT SEAT CUSHION ASSEMBLY
(a) Using a clip remover, remove the 2 clips.
(b) Remove the 2 front seatback cover bands.
Protective Tape
B130675E01
Protective Tape
B130677E01
B130701
B130680
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст