Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 133
ENGINE HOOD / DOOR – ACCESS DOOR
ED–29
ED
DISASSEMBLY
HINT:
•
Use the same procedure for both RH and LH sides.
•
The procedure described below is for the RH side.
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2.
REMOVE ACCESS PANEL REAR WEATHERSTRIP
(a) Remove the access panel rear weatherstrip.
3.
REMOVE LAP BELT OUTER ANCHOR COVER
(a) Disengage the 3 claws and remove the lap belt
outer anchor cover.
4.
REMOVE REAR DOOR INSIDE HANDLE SUB-
ASSEMBLY
(a) Insert a clip remover between the handle and door
trim.
(b) Turn the handle with the clip remover inserted, as
shown in the illustration.
(c) Remove the rear door inside handle and snap ring.
5.
REMOVE NO. 1 CUP HOLDER
(a) Remove the screw and the No. 1 cup holder.
B135524
B135525
B135527
B135528
ED–30
ENGINE HOOD / DOOR – ACCESS DOOR
ED
6.
REMOVE REAR DOOR TRIM BOARD SUB-
ASSEMBLY
(a) Remove the bolt and separate the front seat belt
outer (floor side).
(b) Disengage the 9 clips and remove the rear door trim
panel.
7.
REMOVE NO. 1 DOOR TRIM BRACKET
(a) Remove the 2 screws and remove the No. 1 door
trim bracket.
8.
REMOVE CENTER PILLAR UPPER GARNISH
(a) Remove the clip.
(b) Remove the 2 screws.
(c) Disengage the 2 clips and remove the center pillar
upper garnish.
9.
REMOVE FRONT SEAT OUTER BELT ASSEMBLY
(See page
10. REMOVE FRONT SHOULDER BELT ANCHOR
ADJUSTER ASSEMBLY (See page
B135526
B135558
B135529
B135559
B135560
ENGINE HOOD / DOOR – ACCESS DOOR
ED–31
ED
11. REMOVE ACCESS PANEL INSIDE HANDLE SUB-
ASSEMBLY
(a) Disconnect the rod.
(b) Remove the 3 bolts, then remove the access panel
inside handle.
12. REMOVE ACCESS PANEL UPPER LOCK ASSEMBLY
)
13. REMOVE ACCESS PANEL LOWER LOCK
ASSEMBLY (See page
14. REMOVE ACCESS PANEL LOCK REMOTE
CONTROL ASSEMBLY
(a) Disconnect the rod and connector clamp.
(b) Remove the 2 bolts, then remove the access panel
lock remote control.
15. REMOVE ACCESS PANEL LOCK CANCEL LEVER
ASSEMBLY
(a) Using "Torx" socket wrench T30, remove the 2
screws and remove the access panel lock cancel
lever.
16. REMOVE FRONT DOOR COURTESY SWITCH (See
page
17. REMOVE ACCESS PANEL LOCK STRIKER PLATE
ASSEMBLY
(a) Using "Torx" socket wrench T40, remove the 2
screws and access panel lock striker plate.
18. REMOVE REAR DOOR SERVICE HOLE COVER
(a) Remove the rear door service hole cover.
NOTICE:
Remove any tape remaining on the door side.
B135530
B135533
B135534
B135535
B135536
ED–32
ENGINE HOOD / DOOR – ACCESS DOOR
ED
19. REMOVE REAR DOOR OPENING TRIM
(a) Remove the rear door opening trim.
20. REMOVE ACCESS PANEL CHECK ASSEMBLY
(a) Remove the bolt and 2 nuts, then remove the
access panel check.
NOTICE:
Do not drop or damage the access panel check
when removing the bolt and nuts.
HINT:
Remove the access panel check through the
service hole.
21. REMOVE ACCESS PANEL WEATHERSTRIP
(a) Disengage the 6 clips.
B135537
B135538
B135539
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст