Toyota FJ Cruiser (GSJ 10, 15 series). Instruction — part 421
MT–30
RA61F MANUAL TRANSMISSION – MANUAL TRANSMISSION UNIT
MT
REASSEMBLY
1.
INSTALL 1ST AND REVERSE SHIFT ARM
(a) Install the shift arm and shift arm pivot onto the
interlock bracket.
(b) Install a new E-ring onto the shift arm pivot.
2.
INSTALL NO. 4 GEAR SHIFT FORK SHAFT
(a) Install the spring and ball onto the interlock bracket.
(b) Install the No. 4 shift fork shaft.
3.
INSTALL NO. 4 GEAR SHIFT FORK
(a) Install the No. 4 shift fork onto the No. 4 shift fork
shaft .
(b) Using a pin punch (5 mm (0.20 in.)) and hammer,
tap a new slotted pin into the No. 4 shaft fork and
No. 4 shift fork shaft.
Drive in depth:
0 to 0.5 mm (0 to 0.050 in.)
4.
INSTALL NO. 1 GEAR SHIFT FORK
(a) Install the No. 1 shift fork and No. 2 shift head onto
the No. 4 shift fork shaft.
(b) Using a pin punch (5 mm (0.20 in.)) and hammer,
tap a new slotted pin into the No. 2 shaft head and
No. 4 shift fork shaft.
Drive in depth:
0 to 0.5 mm (0 to 0.050 in.)
D033725
D033724
D033723
C136398
C136399
RA61F MANUAL TRANSMISSION – MANUAL TRANSMISSION UNIT
MT–31
MT
5.
INSTALL NO. 1 GEAR SHIFT FORK SHAFT
(a) Apply MP grease to the No. 1 interlock pin and
install it into the interlock bracket.
(b) Install the spring and ball into the interlock bracket.
(c) Install the No. 1 shift fork shaft onto the interlock
bracket.
HINT:
Place the No. 4 shift fork shaft in the neutral
position.
6.
INSTALL NO. 1 GEAR SHIFT HEAD
(a) Install the No. 1 shift head into the No. 1 shift fork
shaft.
(b) Using a pin punch (5 mm (0.20 in.)) and hammer,
tap a new slotted pin into the No. 1 shaft head and
No. 1 shift fork shaft.
Drive in depth:
0 to 0.5 mm (0 to 0.050 in.)
7.
INSTALL NO. 2 GEAR SHIFT FORK SHAFT
(a) Apply MP grease to the No. 2 and No. 3 interlock
pins, then install them onto the interlock bracket.
(b) Install the spring and ball into the interlock bracket.
(c) Install the No. 2 shift fork shaft onto the interlock
bracket.
HINT:
Place the No. 3 and No. 4 shift fork shafts in the
neutral position.
8.
INSTALL NO. 2 GEAR SHIFT FORK
(a) Install the No. 2 shift fork with the bolt.
Torque: 20 N*m (199 kgf*cm, 14 ft.*lbf)
9.
INSTALL NO. 3 GEAR SHIFT FORK SHAFT
(a) Apply MP grease to the No. 2 and No. 3 interlock
pins, then install them onto the interlock bracket.
(b) Install the spring and ball into the interlock bracket.
(c) Install the No. 3 shift fork shaft onto the interlock
bracket.
HINT:
Place the No. 2, No. 1 and No. 4 shift fork shafts in
the neutral position.
F051831
C136400
F051830
F051589
F051829
MT–32
RA61F MANUAL TRANSMISSION – MANUAL TRANSMISSION UNIT
MT
10. INSTALL NO. 3 GEAR SHIFT FORK
(a) Install the No. 3 shift fork with the bolt.
Torque: 20 N*m (199 kgf*cm, 14 ft.*lbf)
11. INSTALL TRANSMISSION CASE OIL SEAL
(a) Using SST and a hammer, tap a new oil seal into
the front case in accordance with the dimension
specified in the illustration.
SST
09950-70010 (09951-07100), 09950-60010
(09951-00470)
Dimension A:
60.0 to 60.8 mm (2.362 to 2.394 in.)
(b) Apply gear oil to the lip of the oil seal.
12. INSTALL FRONT BEARING SHAFT SNAP RING
(a) Using snap ring pliers, install the 2 snap rings.
13. INSTALL NO. 1 OIL RECEIVER PIPE
(a) Install the No. 1 oil receiver pipe onto the
transmission front case.
HINT:
Align the convex portion of the oil receiver pipe with
the cutout of the front case and install the oil
receiver pipe onto the clutch housing.
14. INSTALL TRANSMISSION FRONT CASE
(a) Apply gear oil to all sliding and rotating parts.
(b) Provisionally install the output shaft, input shaft,
counter gear shaft and control assembly, and tie
them with a piece of rope or string.
F051588
SST
A
D033643E01
D033639
D033642
D033644
RA61F MANUAL TRANSMISSION – MANUAL TRANSMISSION UNIT
MT–33
MT
(c) Using a snap ring expander, extend the 2 snap rings
and install the output shaft, input shaft, counter gear
shaft and control assembly.
HINT:
Make sure that the snap ring is fitted into the
grooves of the input shaft and front bearing of the
counter gear shaft.
(d) Untie the output shaft, input shaft, counter gear
shaft and control assembly.
(e) Using a hexagonal wrench (24 mm), install the plug
onto the front case.
Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf)
(f)
Install the interlock bracket with the 4 bolts.
Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf)
15. INSTALL REVERSE IDLER GEAR
(a) Install the reverse idler gear, reverse idler gear
bearing and reverse idler gear shaft.
HINT:
Make sure that the reverse idler gear faces the
correct direction as shown in the illustration.
NOTICE:
Make sure that the hole in the reverse idler shaft
is in the position shown in the illustration.
D033637
F051583
D033635
15
q
C116297E01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст