Volvo V70 (2016 year). Instruction — part 15
07 Driver support
07
*
Option/accessory, for more information, see Introduction.
253
Related information
•
Park assist camera - settings (p. 253)
•
Park assist camera - limitations (p. 254)
•
Park assist camera - settings
Activate switched-off camera
If the camera function is switched off when
reverse gear is selected, it is activated in the
following way:
•
Press CAM - the screen shows the cur-
rent camera view.
Change setting
The default setting is that the camera is acti-
vated when reverse gear is selected.
The settings for the parking camera can be
changed when the screen shows a camera
view:
1. Press OK/MENU when a camera view is
shown - the screenchanges to a menu
with various options.
2. Turn to reach the desired option with
TUNE.
3. Highlight the option by pressing OK/
MENU once and go back out with EXIT.
Miscellaneous
If the car has several cameras* installed, the
active camera view on the screen can be
changed:
•
Press CAM or turn TUNE.
Related information
•
•
07 Driver support
07
254
*
Option/accessory, for more information, see Introduction.
Park assist camera - limitations
A bike carrier or other accessory mounted
on the rear of the car could obscure the
camera's view.
To bear in mind
Pay attention to the possibility that, even if it
only looks like a relatively small part of the
image is obscured, it could be a relatively
large sector that is hidden from view. Obsta-
cles could thereby go undetected until they
are very close to the car.
•
Keep the camera lens free from dirt, ice
and snow.
•
Clean the camera lens regularly with luke-
warm water and car shampoo - take care
not to scratch the lens.
Related information
•
•
Park assist camera - settings (p. 253)
•
BLIS*
BLIS (Blind Spot Information) is a camera-
based information system that under certain
conditions can help the driver to notice vehi-
cles moving in the same direction as the host
vehicle in the so-called "blind spot".
The system is designed to work most effec-
tively when driving in dense traffic on multi-
lane highways.
WARNING
The system is a supplement to, not a
replacement for, a safe driving style and
use of the rearview mirrors. It can never
replace the driver's attention and responsi-
bility. The responsibility for changing lanes
safely always rests with the driver.
Overview
G021426
Rearview mirror with BLIS function
37
.
BLIS camera
Indicator lamp
BLIS symbol
The lamp illuminates on the side of the car
where the system has detected the vehi-
cle. If the car is overtaken on both sides at
the same time then both lamps illuminate.
Maintenance
In order to work most effectively the BLIS
camera lenses
38
must be clean. The lenses
can be cleaned with a soft cloth or damp
37
NOTE: The illustration is schematic - details may vary depending on car model.
38
See (1) in the preceding illustration.
07 Driver support
07
}}
*
Option/accessory, for more information, see Introduction.
255
sponge. Clean the lenses carefully so that
they are not scratched.
The lenses are electrically heated to melt
ice or snow. If necessary, brush snow
away from the lenses.
Related information
•
•
BLIS - symbols and messages (p. 257)
BLIS* - operation
BLIS (Blind Spot Information) is a function
designed for providing support for the driver
when driving in dense traffic on roads with
several lanes in the same direction.
Activate/deactivate BLIS
BLIS is activated when the engine is started.
The indicator lamps in the door panels flash
three times when BLIS is activated.
Button for activating/deactivating.
The system can be deactivated/activated
after starting the engine with one press on the
BLIS button.
Some combinations of the selected equip-
ment leave no vacant space for a button in
the centre console - in which case the func-
tion is operated in the car's menu system
(p. 116) MY CAR.
When BLIS is deactivated, the lamp in the
button extinguishes and a message is shown
in the combined instrument panel.
When BLIS is activated the lamp in the button
illuminates, the combined instrument panel
shows a new text message and the indicator
lamps in the door panels flash 3 times. Press
the left-hand stalk switch OK button in order
to switch off the text message.
When BLIS operates
A = approx. 9.5 m and B = approx. 3.0 m.
The system operates when the car is driven
at a speed above 10 km/h.
When a camera (1) has detected a vehicle
inside the blind spot zone the indicator lamp
(2) illuminates with a constant glow, see over-
view illustration (p. 254).
BLIS advises the driver with a message if a
fault arises in the system. If, for example, the
||
07 Driver support
07
256
system's cameras are obscured then the
BLIS indicator lamp flashes and a message is
shown in the combined instrument panel. In
such cases, check and clean the lenses.
If necessary, the system can be switched off
temporarily, see "Activate/deactivate BLIS"
above.
Overtaking
The system is designed to react if:
•
you overtake another vehicle at a speed
of up to 10 km/h faster than the other
vehicle
•
you are overtaken by a vehicle travelling
up to 70 km/h faster than you are travel-
ling.
WARNING
BLIS does not work in sharp bends.
BLIS does not work when the car is
reversing.
A wide trailer coupled to the car can con-
ceal other vehicles in adjacent lanes. It can
prevent the vehicle in the screened area
from being detected by BLIS.
Daylight and darkness
In daylight the system reacts to the shape of
the surrounding vehicles. The system is
designed to detect motor vehicles such as
cars, trucks, buses and motorcycles.
In darkness the system reacts to the head-
lamps of surrounding vehicles. If the head-
lamps of surrounding vehicles are not
switched on then the system does not detect
the vehicles. This means for example that the
system does not react to a trailer without
headlamps which is towed behind a car or
truck.
WARNING
The system does not react to cyclists or
moped riders.
The BLIS cameras have limitations similar
to those of the human eye, i.e. they do not
"see" as well e.g. in heavy snowfall,
against strong light or in thick fog.
Limitations
In some situations the BLIS indicator lamp
may illuminate despite there being no other
vehicle within the blind spot.
If the BLIS indicator lamp illuminates on
isolated occasions despite there being no
other vehicle within the blind spot then this
does not mean that a fault has arisen in
the system.
In the event of a fault in the BLIS system
the display shows the text
BLIS Service
required
.
The following illustrations show examples of
situations where the BLIS indicator lamp may
illuminate even if there is no other vehicle
within the blind spot.
Reflection from shiny wet road surface.
Own shadow on large light smooth surface, e.g.
noise barrier or concrete road surface.
07 Driver support
07
*
Option/accessory, for more information, see Introduction.
257
Low stationary sunlight shining into the camera.
Repair of the BLIS system components
must only be performed by a workshop -
an authorised Volvo workshop is recom-
mended.
Related information
•
•
BLIS - symbols and messages (p. 257)
BLIS - symbols and messages
In situations where the BLIS (Blind Spot
Information) (p. 254) function fails or is inter-
rupted, the combined instrument panel may
show a symbol, supplemented by an explana-
tory message. Follow any recommendation
given.
Message examples:
Message
Specification
BLIS ON
The BLIS system is acti-
vated.
BLIS Serv-
ice required
Blind spot syst. disen-
gaged - contact a work-
shop.
BLIS Cam-
era blocked
The BLIS camera is
blocked by dirt, snow or
ice - clean the lenses.
Message
Specification
BLIS
Reduced
function
Reduced function in the
data transmission between
the BLIS system's camera
and the car's electrical sys-
tem.
The camera resets itself
when the data transmis-
sion between the BLIS sys-
tem's camera and the car's
electrical system returns to
normal.
BLIS OFF
The BLIS system is deacti-
vated.
A text message can be acknowledged by
briefly pressing the OK button on the direc-
tion indicator stalk.
Related information
•
08 Starting and driving
08
260
*
Option/accessory, for more information, see Introduction.
Alcohol lock*
The function of the alcohol lock is to prevent
the car from being driven by individuals under
the influence of alcohol. Before the engine
can be started the driver must take a breath
test that verifies that he/she is not under the
influence of alcohol. Alcohol lock calibration
takes place in accordance with each market's
limit value in force for driving legally.
WARNING
The alcohol lock is an aid and does not
exempt the driver from responsibility. It is
always the responsibility of the driver to be
sober and to drive the car safely.
Related information
•
Alcohol lock* - functions and operation
•
Alcohol lock* - storage (p. 261)
•
Alcohol lock* - before starting the engine
•
Alcohol lock* - to bear in mind (p. 263)
•
Alcohol lock* - symbols and text mes-
Alcohol lock* - functions and
operation
Functions
Nozzle for breath test.
Switch.
Transmission button.
Lamp for battery status.
Lamp for result of breath test.
Lamp indicates ready for breath test.
Operation - battery
Alcohol lock indicator lamp (4) shows battery
status:
Indicator
lamp (4)
Battery status
Flashing
green
Charging in progress
Green
Fully charged
Yellow
Semi-charged
Red
Discharged - fit the charger
in the holder or connect the
power supply cable from
the glovebox.
Store the alcohol lock in its holder. This
will keep the built-in battery fully charged
and the alcohol lock is activated automati-
cally when the car is opened.
Related information
•
•
Alcohol lock* - storage (p. 261)
•
Alcohol lock* - before starting the engine
•
Alcohol lock* - to bear in mind (p. 263)
•
08 Starting and driving
08
}}
*
Option/accessory, for more information, see Introduction.
261
Alcohol lock* - storage
Store the alcohol lock in its holder. Release
the handheld unit by depressing it slightly in
its holder and releasing it - it then springs out
and can be removed from the holder.
Handheld unit storage and charging station.
•
Replace the handheld unit in the holder
by pushing it in until it engages.
•
Store the handheld unit in the holder -
this provides it with the best protection
and keeps its batteries fully charged.
Related information
•
•
Alcohol lock* - functions and operation
•
Alcohol lock* - before starting the engine
•
Alcohol lock* - to bear in mind (p. 263)
•
Alcohol lock* - symbols and text mes-
Alcohol lock* - before starting the
engine
The alcohol lock is activated automatically
and is then ready for use when the car is
opened.
Nozzle for breath test.
Switch.
Transmission button.
Lamp for battery status.
Lamp for result of breath test.
Lamp indicates ready for breath test.
1. When the indicator lamp (6) is green the
alcohol lock is ready for use.
2. Withdraw the alcohol lock from its holder.
If the alcohol lock is outside the car when
||
08 Starting and driving
08
262
*
Option/accessory, for more information, see Introduction.
it is unlocked then it must first be acti-
vated with the switch (2).
3. Lift up the nozzle (1), take a deep breath
and blow with an even pressure until a
"click" is heard after approx. 5 seconds.
The result will be one of the alternatives in
the following table Result after breath
test.
4. If no message is shown then the trans-
mission to the car may have failed - in
which case, press the button (3) to trans-
mit the result to the car manually.
5. Fold down the nozzle and refit the alcohol
lock in its holder.
6. Start the engine following an approved
breath test within 5 minutes - otherwise it
must be repeated.
Result after breath test
Indicator lamp
(5) + Display
text
Specification
Green lamp +
Alcoguard
Approved test
Start the engine - no
alcohol content meas-
ured.
Yellow lamp +
Alcoguard
Approved test
Engine starting possi-
ble - measured alco-
hol content is above
0.1 mg/ml but below
the limit value in
force
A
.
Red lamp +
Dis-
approved test
Wait 1 minute to
try again
Engine starting not
possible - measured
alcohol content is
above the limit value
in force
A
.
A
Limit values vary from country to country. Find out what
applies in your country. See also Alcohol lock* (p. 260).
After a completed period of driving, the
engine can be restarted within 30 minutes
without a new breath test.
Related information
•
•
Alcohol lock* - functions and operation
•
Alcohol lock* - storage (p. 261)
•
Alcohol lock* - to bear in mind (p. 263)
•
08 Starting and driving
08
}}
*
Option/accessory, for more information, see Introduction.
263
Alcohol lock* - to bear in mind
In order to obtain correct function and as
accurate a measurement result as possible:
•
Avoid eating or drinking
approx. 5 minutes before the breath test.
•
Avoid excess windscreen washing - the
alcohol in the washer fluid may result in
an incorrect measurement result.
Change of driver
In order to ensure that a new breath test is
carried out in the event of a change of driver -
depress the switch (2) and the send button (3)
simultaneously for approx. 3 seconds. At
which point the car returns to start inhibition
mode and a new approved breath test is
required before starting the engine.
Calibration and service
The alcohol lock must be checked and cali-
brated at a workshop
1
every 12 months.
30 days before recalibration is necessary the
combined instrument panel shows the mes-
sage
Alcoguard Calibration required See
manual
. If calibration is not carried out within
these 30 days then normal engine starting will
be blocked - only starting with the Bypass
function will then be possible, see the follow-
ing heading "Emergency situation".
The message can be cleared by pressing the
send button (3) once. Otherwise it extin-
guishes on its own after approx. 2 minutes
but then reappears each time the engine is
started - only recalibration at a workshop
1
can clear the message permanently.
Cold or hot weather
The colder the weather the longer it takes
before the alcohol lock is ready for use:
Temperature (ºC)
Maximum heat-
ing time (sec-
onds)
+10 to +85
10
-5 to +10
60
-40 to -5
180
At temperatures below -20 ºC or above
+60 ºC the alcohol lock requires additional
power supply. The combined instrument
panel shows
Alcoguard Please insert
power cable
. In which case, connect the
power supply cable from the glovebox and
wait until indicator lamp (6) is green.
In extremely cold weather the heating time
can be reduced by taking the alcohol lock
indoors.
Emergency situation
In the event of an emergency situation or the
alcohol lock is out of order, it is possible to
bypass the alcohol lock in order to drive the
car.
All Bypass activation is logged and saved
in memory, see Recording data (p. 18).
After the Bypass function has been activated
the combined instrument panel shows
Alcoguard Bypass enabled
the whole time
while driving and can only be reset by a work-
shop
1
.
The Bypass function can be tested without
the error message being logged - in which
case, carry out all the steps without starting
the car. The error message is cleared when
the car is locked.
When the alcohol lock is installed, either the
Bypass or Emergency function is selected as
the bypassing option. This setting can be
changed afterwards at a workshop
1
.
Activating the Bypass function
•
Depress and hold the left-hand stalk
switch OK button and the button for haz-
ard warning flashers simultaneously for
approx. 5 seconds - the combined instru-
ment panel first shows
Bypass activated
1
An authorised Volvo workshop is recommended.
||
08 Starting and driving
08
264
*
Option/accessory, for more information, see Introduction.
Please wait for 1 minute
and then
Alcoguard Bypass enabled
- after
which the engine can be started.
This function can be activated more than
once. The error message shown during driv-
ing can only be cleared at a workshop
1
.
Activating the Emergency function
•
Depress and hold the left-hand stalk
switch OK button and the button for haz-
ard warning flashers simultaneously for
approx. 5 seconds - the combined instru-
ment panel shows
Alcoguard Bypass
enabled
and the engine can be started.
This function can be used once, after which a
reset must be made at a workshop
1
.
Related information
•
Alcohol lock* - functions and operation
•
Alcohol lock* - storage (p. 261)
•
Alcohol lock* - before starting the engine
•
•
Alcohol lock* - symbols and text mes-
Alcohol lock* - symbols and text
messages
In addition to the previously described mes-
sages related to how the alcohol lock works
before starting the engine (p. 261) the com-
bined instrument panel's display can also
show the following:
Display text
Meaning/Action
Alcoguard
Restart possi-
ble
The engine has been
switched off for less
than 30 minutes -
engine starting possible
without new test.
Alcoguard
Service
required
Contact a workshop
A
.
Alcoguard No
signal
received
Transmission failed -
send manually with but-
ton (3) or take a new
breath test.
Alcoguard
Please try
again
Test failed - take a new
breath test.
Alcoguard
Please blow
longer
Blowing too short - blow
for longer.
Display text
Meaning/Action
Alcoguard
Please blow
softer
Blowing too hard - blow
more gently.
Alcoguard
Please blow
harder
Blowing too weak -
blow harder.
Alcoguard
preheating
Please wait
Heating not finished -
wait for text
Alcoguard
Please blow for 5 sec-
onds
.
A
An authorised Volvo workshop is recommended.
Related information
•
•
Alcohol lock* - functions and operation
•
Alcohol lock* - storage (p. 261)
•
Alcohol lock* - before starting the engine
•
Alcohol lock* - to bear in mind (p. 263)
1
An authorised Volvo workshop is recommended.
08 Starting and driving
08
}}
*
Option/accessory, for more information, see Introduction.
265
Starting the engine
The engine is started and switched off using
the remote control key and the START/STOP
ENGINE button.
Ignition switch with remote control key extrac-
ted/inserted and START/STOP ENGINE button.
Do not press in the remote control key
incorrectly turned - hold the end with the
detachable key blade, see Detachable key
blade - detaching/attaching (p. 174).
1. Insert the remote control key in the igni-
tion switch and press it in to its end posi-
tion. Note that if the car is equipped with
alcohol lock* then a breath test must first
be approved before the engine can be
started. For more information on the
Alcohol lock, see Alcohol lock* (p. 260).
2. Hold the clutch pedal fully depressed
2
.
(For cars with automatic gearbox -
Depress the brake pedal.)
3. Press the START/STOP ENGINE button
and then release it.
For diesel-engined cars, there may be a
slight delay before the engine can be
started -
Engine preheating
is displayed
in the meantime.
When the engine is started the starter motor
works until the engine is started or until its
overheating protection triggers.
If the engine fails to start after 3 attempts -
wait for 3 minutes before making a further
attempt. Starting capacity increases if the
battery is allowed to recover.
WARNING
Never remove the remote control key from
the ignition switch after starting the engine
or when the car is being towed.
WARNING
Always remove the remote control key
from the ignition switch when leaving the
car, and make sure that the key position is
0 - in particular if there are children in the
car. For information on how this works -
The idling speed can be noticeably higher
than normal for certain engine types during
cold starting. This is done in order that the
emissions system can reach normal oper-
ating temperature as quickly as possible,
which minimises exhaust emissions and
protects the environment.
Keyless drive*
Follow steps 2-3 for keyless (p. 178) starting
of the engine.
2
If the car is moving then it is enough to press the START/STOP ENGINE button to start the engine.
||
08 Starting and driving
08
266
A prerequisite for the engine to start is that
one of the car's remote control keys with
the Keyless drive function is in the passen-
ger compartment or cargo area.
WARNING
Never remove the remote control key from
the car while driving or during towing.
Related information
•
Switching off the engine (p. 266)
Switching off the engine
The engine is switched off using the START/
STOP ENGINE button.
To stop the engine:
•
Press START/STOP ENGINE - the
engine stops.
If the gear selector is not in P position or if
the car is moving:
•
Press twice on START/STOP ENGINE or
hold the button depressed until the
engine stops.
Related information
•
Steering lock
The steering lock makes steering difficult if
the car is e.g. taken unlawfully. A mechanical
noise may be noticed when the steering lock
unlocks or locks.
Function
•
The steering lock is activated when the
driver's door is opened after the engine
has been switched off.
•
The steering lock is deactivated when the
remote control key is in the ignition
switch
3
and the START/STOP ENGINE
button is depressed.
Related information
•
•
•
3
Cars with Keyless drive only need to have a remote control key inside the passenger compartment.
08 Starting and driving
08
}}
*
Option/accessory, for more information, see Introduction.
267
Remote start (ERS)*
Remote start (ERS – Engine Remote Start)
means that the car's engine can be started
remotely in order to warm up/cool down the
passenger compartment before departure.
ERS is activated via key and/or via Volvo On
Call*.
The climate control starts with the same set-
tings that were being used when the car was
parked.
An ERS-started engine is activated for a
maximum of 15 minutes, then it is switched
off. After two ERS-activations the engine
must be started in the normal way before
ERS can be re-used.
ERS is only available in cars with automatic
gearbox and cars that have a bonnet switch
4
installed.
The service life of the remote control key's
battery is affected by the ERS function. In
the event of frequent use of ERS the bat-
tery should therefore be changed once per
year, see Remote control key - replacing
Follow local/national rules/regulations on
idling. Also take into account the local/
national rules/regulations regarding the
noise level when the engine is running.
WARNING
To remote-start the engine, the following
criteria must be met:
•
The car must be supervised.
•
There must be no people or animals
inside or around the car.
•
The car must not be parked in a
closed, unventilated area - the exhaust
gases may seriously injure humans
and animals.
Related information
•
Remote start (ERS) - operation (p. 267)
•
Remote start (ERS) - symbols and mes-
Remote start (ERS) - operation
The key's buttons for remote start.
Unlocking
Locking
Approach lighting
Unlocking, tailgate
Information
5
Remote starting the engine
To be able to remotely start the engine the
car must be locked and the bonnet closed.
Proceed as follows:
4
Available in the XC60, cars with alarm, most cars with 4-cylinder engines or if ERS is selected for new construction.
5
Only on PCC key, see Remote control key with PCC* - unique functions (p. 172).
||
08 Starting and driving
08
268
*
Option/accessory, for more information, see Introduction.
1. Briefly press on the key's button (2).
2. Follow this immediately afterwards with a
long press - at least 2 seconds - on
button (3).
If the conditions for ERS are fulfilled then the
following takes place:
1. The direction indicators flash quickly sev-
eral times.
2. The engine starts.
3. The direction indicators illuminate with a
constant glow for 3 seconds to verify that
the engine has started.
After remote starting, the car continues to
be locked but with deactivated movement
detector*.
With PCC
6
key
The light indication for Approach
lighting
7
flashes several times when
the button is pressed and then goes
to constant glow if all criteria for
ERS have been fulfilled. However, this does
not mean that ERS has started the engine.
To check whether ERS has started the
engine, the user can press the button (5) - if
the engine has started, there is a light indica-
tion by the buttons (2) and (3).
Active functions
The following functions are activated with a
remote started engine:
•
Ventilation system
•
Audio/video system
•
Approach lighting.
Deactivated functions
The following functions are deactivated with a
remote started engine:
•
headlamps
•
Position lamps
•
Number plate lighting
•
Windscreen wiper.
ERS is interrupted
The following steps switch off an ERS-started
engine:
•
The remote control key's button
(1), (2) or (4) is depressed
•
The car is unlocked
•
A door is opened
•
Accelerator pedal or brake pedal is
depressed
•
The gear selector is moved out of P posi-
tion
•
Active ERS time exceeds 15 minutes.
When an ERS-started engine is switched off,
the direction indicators illuminate with a con-
stant glow for 3 seconds.
Related information
•
•
Remote start (ERS) - symbols and mes-
6
For more information on the PCC key, see Remote control key with PCC* - unique functions (p. 172).
7
For more information on Approach lighting, see Remote control key - functions (p. 170) and Approach lighting (p. 99).
08 Starting and driving
08
}}
269
Remote start (ERS) - symbols and
messages
In situations where the ERS function fails or is
interrupted, a symbol is shown in the com-
bined instrument panel, supplemented by an
explanatory text message.
ERS function unavailable
Message
Specification
No remote
start Too
many tries
ERS unavailable
because a maximum of 2
ERS activations in suc-
cession are allowed.
No remote
start Low fuel
level
ERS unavailable
because fuel level too
low.
No remote
start Gear not
in P
ERS unavailable
because gear selector is
not in P position.
No remote
start Driver in
car
ERS unavailable
because someone is in
the passenger compart-
ment.
No remote
start Low
battery
ERS unavailable due to
low battery voltage.
Charge the battery by
starting the engine.
Message
Specification
No remote
start Engine
warning
ERS unavailable due to
warning message from
engine. Contact a work-
shop
A
.
No remote
start Engine
coolant level
low
ERS unavailable due to
error message from
cooling system, see
No remote
start Door
open
ERS unavailable
because a door/tailgate
was not closed.
No remote
start Bonnet
open
ERS did not activate
because the bonnet was
not closed.
No remote
start Car not
locked
ERS unavailable
because the car was not
locked.
No remote
star Key in
car
ERS did not activate
because the key was in
the car.
A
An authorised Volvo workshop is recommended.
Interrupted ERS function
Message
Specification
Remote start
off Gear not in
P
ERS interrupted
because gear selector
is not in P position.
Remote start
off Driver in
car
ERS interrupted
because someone is in
the passenger compart-
ment.
Remote start
off Engine
warning
ERS interrupted due to
error message from
engine. Contact a work-
shop
A
.
No remote
start Engine
coolant level
low
ERS interrupted due to
error message from
cooling system.
Remote start
off Bonnet
open
ERS interrupted
because the bonnet is
open.
Remote start
off Low bat-
tery
ERS interrupted since
the battery voltage is
too low.
Remote start
off Low fuel
level
ERS interrupted since
the fuel level is too low.
A
An authorised Volvo workshop is recommended.
||
08 Starting and driving
08
270
*
Option/accessory, for more information, see Introduction.
Related information
•
•
Remote start (ERS) - operation (p. 267)
Jump starting with battery
If the starter battery (p. 378) is discharged
then the car can be started with current from
another battery.
When jump starting the car, the following
steps are recommended to avoid short cir-
cuits or other damage:
1. Set the car's electrical system in key
position 0, see Key positions - functions
2. Check that the donor battery has a volt-
age of 12 V.
3. If the donor battery is installed in another
car - switch off the donor car's engine
and make sure that the two cars do not
touch each other.
4. Connect one of the red jump lead's
clamps to the donor battery's positive
terminal (1).
Connect the start cable carefully to avoid
short circuits with other components in the
engine compartment.
5. Open the clips on the front cover of the
battery in your car and remove the cover,
see Starter battery - replacement
6. Connect the red jump lead's other clamp
onto the car's positive terminal (2).
7. Connect one of the black jump lead's
clamps to the donor battery's negative
terminal (3).
8. Connect the other clamp to a grounding
point, e.g. right-hand engine mounting at
the top, the outer screw head (4).
9. Check that the jump lead clamps are
affixed securely so that there are no
sparks during the starting attempt.
10. Start the engine of the "donor car" and
allow it to run a few minutes at a speed
slightly higher than idle
approx. 1500 rpm.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст