Volvo V40 Cross Country (2018 year). Instruction — part 19
WHEELS AND TYRES
* Option/accessory.
327
Warning triangle
The warning triangle is used to warn other road
users of a stationary vehicle.
Storage and folding up
Lift the floor hatch (or push the rear part of
the luggage compartment floor forwards in
models with a jointed floor and then lift the
lower floor) and remove the warning triangle.
Take the warning triangle from the case, fold
out and assemble the two loose sides.
Fold out the warning triangle's support legs.
Follow the regulations for the use of a warning
triangle. Position the warning triangle in a suita-
ble place with regard to traffic.
Ensure the warning triangle and its case are
properly secured in the cargo area after use.
Related information
•
Jack*
Use the jack to raise the car when changing a
wheel.
Only use the original jack when fitting a spare
wheel or when changing between summer and
winter wheels. The jack's thread must always be
well greased.
The tools and jack
* must be stored in the
intended location in the car's cargo area
when not in use.
The normal car jack is only designed for occa-
sional, short-term use, such as when chang-
ing a wheel after a puncture, changing to win-
ter/summer wheels, etc. Only the jack for the
specific car model may be used to raise the
car. If the car is to be jacked up more often, or
for a longer time than is required just to
change a wheel, use of a garage jack is rec-
ommended. In this instance, follow the
instructions for use that come with the equip-
ment.
Related information
•
•
WHEELS AND TYRES
* Option/accessory.
328
First aid kit*
The first aid box contains first aid equipment.
A case containing first aid equipment is located
on the left-hand side of the cargo area.
Tyre monitoring (TM)*
1
The TM (Tyre Monitor) system senses the rota-
tion speed of the tyres in order to determine
whether they have the correct tyre pressure.
System description
If the tyre pressure is too low, the tyre's diameter
is changed and, as a result, so is its rotation
speed. By comparing the tyres with each other
the system can determine whether one or more
tyres have pressure that is too low.
The system does not replace normal tyre mainte-
nance.
Messages
If the tyre pressure is too low then an indicator
symbol (
) illuminates in the combined instru-
ment panel and one of the following messages is
shown:
•
Tyre pressure low Check, adjust and
calibrate
•
Tyre pressure system Service required
•
Tyre pressure system Currently
unavailable
If a fault occurs in the TM system the indica-
tor symbol
in the combined instrument
panel will flash for approx. 1 minute and then
illuminate with a constant glow. A message is
also shown in the combined instrument panel.
1
Standard in certain markets.
WHEELS AND TYRES
}}
329
Deleting the messages
1. Check the tyre pressure in all tyres with a
tyre pressure gauge.
2. Inflate the tyre/tyres to the correct pressure
in accordance with the tyre pressure label on
the driver's side door pillar (between front
and rear doors).
3. Recalibrate the TM system in MY CAR.
To avoid incorrect tyre pressure, the pressure
should be checked on cold tyres. "Cold tyres"
means the tyres are the same temperature as
the ambient temperature (approx. 3 hours
after the car has been driven). After a few kil-
ometres of driving, the tyres warm up and the
pressure increases.
WARNING
•
Incorrect tyre pressure may lead to tyre
failure, which could result in the driver
losing control of the car.
•
The system cannot indicate sudden tyre
damage in advance.
TM calibration
In order for TM system to work correctly, a refer-
ence value for the tyre pressure must be deter-
mined. This must be done each time the tyres are
changed or the tyre pressure is adjusted by reca-
librating the system in MY CAR.
For example, the tyre pressure should be
adjusted when driving with a heavy load or for
high-speed driving (above 160 km/h (100 mph)).
Following which, the system must be recalibrated.
Recalibration
Settings are made using the centre console's
controls, see MY CAR (p. 113).
1. Stop the engine.
2. Inflate all tyres to the desired pressure in
accordance with the tyre pressure label on
the driver's side door pillar (between front
and rear doors).
Or see the tyre pressure table.
3. Start the engine and let the car stand still.
4. Open the menu system MY CAR and select
the menu
Tyre monitor
.
5. Select
Start calibration
and press OK.
6. Press OK after all tyres have been checked
and adjusted in order to start calibration.
7. Drive the car.
> Calibration is performed when the car is
driven at a speed above 35 km/h
(22 mph). Calibration is interrupted tem-
porarily if the engine is switched off, but is
resumed automatically in the background
when the car is driven again. The system
provides no confirmation when the cali-
bration is complete.
The new reference value applies until steps 1-7
are repeated.
Remember that the TM system must be reca-
librated at each tyre change or if the tyre
pressure is adjusted. If new reference values
are not stored then the system cannot func-
tion properly.
•
After a tyre has been inflated, always refit
the dust cap in order to avoid damage to
the valve from gravel, dirt, etc.
•
Only use plastic dust caps. Metal dust
caps can rust and become difficult to
unscrew.
||
WHEELS AND TYRES
* Option/accessory.
330
System and tyre status
The current status of the system and the tyres
can be checked in the centre console's screen.
1. Open the menu system MY CAR.
2. Select the
Tyre monitor
menu.
> Status for tyre pressures is shown with a
colour code.
The status is colour-coded for each tyre in
accordance with the following:
•
All-green: the system is operating normally
and the tyre pressure in all tyres is slightly
above the recommended level.
•
Yellow wheel: corresponding tyre's pressure
is too low.
•
All wheels yellow: two or more tyres have
pressure that is too low.
•
All wheels grey and the message
Tyre
pressure system Currently unavailable
:
the tyre pressure system is temporarily deac-
tivated. It may be necessary to drive the car
for a short time above 35 km/h (22 mph)
before the system becomes active again.
•
All wheels grey and the message
Tyre
pressure system Service required
: an
error has occurred in the system. Contact a
Volvo dealer or workshop.
Related information
•
Emergency puncture repair*
The emergency puncture repair kit, Temporary
Mobility Kit (TMK), is used to seal a puncture
and check and adjust the air pressure.
The emergency puncture repair kit consists of a
compressor and a bottle of sealant. The sealing
works as a temporary repair. The sealing fluid
effectively seals tyres punctured in the tread.
The emergency puncture repair kit has limited
capacity to seal tyres which have punctures in the
wall. Do not use the puncture repair kit on tyres
that have larger slits, cracks or similar damage.
The emergency puncture repair kit is only
intended for sealing tyres with a puncture in
the tread.
The compressor for temporary emergency
puncture repair has been tested and
approved by Volvo.
Location
The puncture repair kit is located in the foam
block
2
under the floor in the cargo area.
Version 1.
Version 2.
WHEELS AND TYRES
}}
* Option/accessory.
331
Related information
•
•
•
Emergency puncture repair kit* -
overview
Overview of the component parts of the emer-
gency puncture repair kit, Temporary Mobility Kit
(TMK).
The parts are stored under the floor in the cargo
area.
Label, maximum permitted speed
Switch
Electrical cable
Bottle holder (orange cap)
Protective cap
Pressure reducing valve
Air hose
Sealing fluid bottle
Pressure gauge
Sealing fluid bottle
Replace the sealing fluid bottle before the expira-
tion date has passed. Treat the old bottle as envi-
ronmentally hazardous waste.
The sealing fluid bottle must be replaced after
use. Volvo recommends that the replacement is
performed by an authorised Volvo workshop.
WARNING
The bottle with sealing fluid contains 1.2-
Ethanol and natural rubber-latex.
Harmful if ingested. Could result in allergic
reaction in the event of skin contact.
Avoid contact with the skin and eyes.
Store out of the reach of children.
2
The foam block may have different appearances depending on the car's equipment.
||
WHEELS AND TYRES
* Option/accessory.
332
WARNING
•
In the event of skin contact with the seal-
ing fluid, it must be washed off immedi-
ately with soap and plenty of water.
•
Sealing fluid that makes contact with an
eye must be rinsed away immediately with
eye wash fluid or with plenty of water. If
the discomfort persists then the eye
should be examined by a doctor.
Related information
•
Emergency puncture repair* -
operation
Sealing a puncture with the emergency puncture
repair kit, Temporary Mobility Kit (TMK).
Emergency puncture repair
For information on the function of the parts, see Emer-
gency puncture repair kit
1. Set up the warning triangle and activate the
hazard warning lights if a tyre is being sealed
in a trafficked location.
If the puncture was caused by a nail or simi-
lar, allow this to remain in the tyre. It helps to
seal the hole.
2. Detach the label for maximum permitted
speed (which is fitted on one side of the
compressor) and affix it to the steering
wheel. You should not drive faster than
80 km/h (50 mph) after the emergency tyre
repair kit has been used.
3. Check that the switch is in position 0 (Off),
and locate the electrical cable and the air
hose.
4. Unscrew the orange-coloured cap from the
compressor, and unscrew the cork from the
sealing fluid bottle.
Do not break the bottle's seal before use. The
seal is broken automatically when the bottle is
screwed in.
WHEELS AND TYRES
}}
333
5. Screw in the bottle to the bottom of the bot-
tle holder.
> The bottle and the bottle holder are
equipped with a reverse catch to prevent
sealant leakage. When the bottle is
screwed in it cannot be unscrewed from
the bottle holder again. Bottle removal
must be performed at a workshop, Volvo
recommends an authorised Volvo work-
shop.
WARNING
•
In the event of skin contact with the seal-
ing fluid, it must be washed off immediately
with soap and plenty of water.
•
Sealing fluid that makes contact with an
eye must be rinsed away immediately with
eye wash fluid or with plenty of water. If the
discomfort persists then the eye should be
examined by a doctor.
WARNING
Do not unscrew the bottle, it is equipped with
a reverse catch to prevent leakage.
6. Unscrew the tyre's dust cap.
Check that the pressure reducing valve on
the air hose is fully screwed on, and screw in
the air hose's valve connection to the bottom
of the thread on the tyre's air valve.
7. Plug the electrical cable into the closest
12 V socket and start the car.
Make sure that none of the other 12 V sock-
ets is in use when the compressor is operat-
ing.
WARNING
Do not leave children in the car without
supervision when the engine is running.
8. Start the compressor by flicking the switch to
position I (On).
WARNING
Never stand next to the tyre when the com-
pressor is running. If cracks or unevenness
arise then the compressor must be switched
off immediately. The journey should not be
continued. Call roadside assistance for recov-
ery to a tyre centre. Volvo recommends an
authorised tyre centre.
When the compressor starts, the pressure
can increase up to 6 bar but the pressure
drops after approximately 30 seconds.
9. Inflate the tyre for 7 minutes.
The compressor must not be operated for
longer than 10 minutes - risk of overheating.
10. Switch off the compressor to check the pres-
sure on the pressure gauge. Minimum pres-
sure is 1.8 bar and maximum 3.5 bar.
(Release air with the pressure reducing valve
if the tyre pressure is too high.)
WARNING
If the pressure is below 1.8 bar (22 psi) then
the hole in the tyre is too big. The journey
should not be continued. Call roadside assis-
tance for recovery to a tyre centre. Volvo rec-
ommends an authorised tyre centre.
11. Switch off the compressor and unplug the
electrical cable.
12. Unscrew the air hose from the tyre's air valve
and refit the dust cap on the tyre.
13. Fit the protective cap on the air hose in order
to avoid leakage of the remaining sealing
fluid.
||
WHEELS AND TYRES
* Option/accessory.
334
14. As soon as possible, drive at least 3 km at a
maximum speed of 80 km/h (50 mph) so
that the sealing fluid can seal the tyre and
then perform a follow-up check.
Sealant will spurt out of the puncture during
the first few rotations of the tyre.
WARNING
Make sure that nobody is standing near the
car and gets the sealing fluid splashed onto
them when the car is driven away. The dis-
tance should be at least 2 metres (7 feet).
15. Follow-up inspection:
Connect the air hose on the tyre's air valve
again and check the tyre pressure with the
pressure gauge, see Emergency puncture
repair
Related information
•
•
•
Emergency puncture repair* -
rechecking
When a tyre has been sealed with the emer-
gency puncture repair kit, Temporary Mobility Kit
(TMK), a subsequent check must be made after
approx. 3 kilometres of driving.
Check tyre pressure
Take out the tyre sealing equipment. The com-
pressor must be switched off.
1. Unscrew the tyre's dust cap.
Take out the air hose and screw in the
valve connection to the bottom of the thread
on the tyre's air valve.
2. Read the tyre pressure on the pressure
gauge.
•
If the tyre pressure is below 1.3 bar then
the tyre is insufficiently sealed. The jour-
ney should not be continued. Call road-
side assistance for recovery.
•
If the tyre pressure is higher than 1.3 bar,
the tyre must be inflated to the pressure
specified in accordance with the tyre
pressure label on the driver side door pil-
lar (1 bar = 100 kPa).
•
Release air using the pressure reducing
valve if the tyre pressure is too high.
3. If the tyre needs to be inflated:
1. Plug the electrical cable into the closest
12 V socket and start the car.
2. Start the compressor and inflate the tyre
to the pressure specified on the tyre pres-
sure label on the driver side door pillar.
3. Switch off the compressor.
4. Remove the tyre sealing equipment.
Fit the protective cap on the air hose in order
to avoid leakage of the remaining sealing
fluid.
WARNING
Do not unscrew the bottle, it is equipped with
a reverse catch to prevent leakage.
5. Refit the dust cap on the tyre.
•
After a tyre has been inflated, always refit
the dust cap in order to avoid damage to
the valve from gravel, dirt, etc.
•
Only use plastic dust caps. Metal dust
caps can rust and become difficult to
unscrew.
WHEELS AND TYRES
* Option/accessory.
335
The sealing fluid bottle and the hose must be
replaced after use. Volvo recommends that
this replacement is performed by an author-
ised Volvo workshop.
WARNING
Check the tyre pressure regularly.
Volvo recommends that the car is driven to the
nearest authorised Volvo workshop for the
replacement/repair of the damaged tyre. Advise
the workshop that the tyre contains sealing fluid.
WARNING
You should not drive faster than 80 km/h
(50 mph) after the emergency tyre repair kit
has been used. Volvo recommends a visit to
an authorised Volvo workshop for inspection
of the sealed tyre (maximum driving distance
is 200 km). The staff there can determine
whether or not the tyre can be repaired or if it
needs to be replaced.
Related information
•
Inflating tyres with compressor from
the emergency puncture repair kit*
The car's original tyres can be inflated using the
compressor in the emergency puncture repair kit
(p. 331).
1. The compressor must be switched off. Make
sure that the switch is in position 0 (Off), and
take out the electrical cable and the air hose.
2. Unscrew the tyre's dust cap and screw in the
air hose's valve connection to the bottom of
the thread on the tyre's air valve.
3. Plug the electrical cable into the closest
12 V socket and start the car.
WARNING
Inhaling car exhaust fumes could result in
danger to life. Never leave the engine running
in sealed areas or areas that lack sufficient
ventilation.
WARNING
Do not leave children in the car without
supervision when the engine is running.
4. Start the compressor by flicking the switch to
position I (On).
The compressor must not be operated for
longer than 10 minutes - risk of overheating.
5. Inflate the tyre to the pressure specified on
the tyre pressure label on the driver side
door pillar. Release air using the pressure
reducing valve if the tyre pressure is too high.
6. Switch off the compressor. Detach the air
hose and the electrical cable.
7. Refit the dust cap on the tyre.
Related information
•
•
MAINTENANCE AND SERVICE
* Option/accessory.
338
Volvo service programme
To keep the car as safe and reliable as possible,
follow the Volvo service programme as specified
in the Service and Warranty Booklet.
Volvo recommends engaging an authorised Volvo
workshop to perform the service and mainte-
nance work. Volvo workshops have the personnel,
special tools and service literature to guarantee
the highest quality of service.
For the Volvo warranty to apply, check and
follow the instructions in the Service and
Warranty Booklet.
Related information
•
Climate control system - fault tracing and
repair (p. 349)
Book service and repair*
1
Manage service, repair and booking information
directly in your Internet-connected car.
This service
1
provides a convenient way to book a
service and workshop visit directly in the car. Car
information is sent to your dealer, who can pre-
pare the workshop visit. The dealer will contact
you to schedule an appointment time. For certain
markets, the system reminds you of a scheduled
appointment time as it approaches and the navi-
gation system
2
can also guide you to the work-
shop when the time comes.
Before the service can be used
Volvo ID and my profile
•
Register a Volvo ID. For more information
and how to create a Volvo ID, see Volvo ID
(p. 20).
•
Go to www.volvocars.com, log in and proceed
as follows:
1. Check that the car is connected to your pro-
file.
2. Check that your contact information is cor-
rect.
3. Select the Volvo dealer you want to contact
for service and repair.
4. Choose preferred communication channel
(phone). Booking information is always sent
to the car and to you via email.
Prerequisite for booking from car
•
To send and receive booking information
from and to the car, the car must be con-
nected to the Internet, see the Sensus Info-
tainment supplement for information about
how to connect the car to the Internet.
•
Since the booking information is sent over
your private phone subscription, you will be
asked whether you want to send the informa-
tion. The question is asked once and then
applies to the selected connection for a lim-
ited time.
•
For the service to work and for the system to
communicate via the car's screen, notifica-
tions/pop-up messages must be accepted.
In the normal view for the MY CAR source,
press OK/MENU and then
Service & repair
Display notifications
.
Using the service
All menus and settings are accessed from the
normal view in MY CAR by pressing OK/MENU
and then
Service & repair
.
When it is time for service, and in some cases
when the car is in need of repair, this is notified
1
Applies to certain markets.
2
Applies to Sensus Navigation.
MAINTENANCE AND SERVICE
}}
339
in the combined instrument panel (p. 66) and via
a pop-up menu in the screen.
Service message in the screen.
Meaning of the answer options in the screen's
pop-up menu:
•
Yes
- A booking enquiry is sent to your
dealer who then comes back with a booking
proposal. The service lamp and service mes-
sage in the combined instrument panel are
extinguished.
•
No
- No more pop-up messages will be
shown in the screen. The message in the
combined instrument panel remains. After
this option has been selected, it is possible
to start the manual booking in the car, see
below.
•
Postpone
- The pop-up menu is shown the
next time the car is started.
Book a service or repair manually
1
1. Press the MY CAR button in the centre con-
sole and select
Service & repair
Dealer
information
Request service or repair
.
> Vehicle data is sent automatically to your
dealer.
2. The dealer sends a booking proposal to the
car.
3. Accept or request a new booking proposal.
After the booking has been accepted the book-
ing information is stored in the car, see My book-
ings. The car will automatically communicate with
you via the screen by means of reminders about
the booking and guide you to the workshop visit.
My bookings
1
Show booking information in the car's screen.
Accept or request a new booking proposal.
–
Select
Service & repair
My bookings
.
Call the dealer
1
With a phone connected to the car via
Bluetooth
®
, you can call your dealer. For connect-
ing the phone, see the Sensus Infotainment sup-
plement.
–
Select
Service & repair
Dealer
information
Call dealer
.
Using the navigation system
1,
2
Enter your workshop as destination or waypoint
in the navigation system.
–
Select
Service & repair
Dealer
information
Set single destination
.
–
Select
Service & repair
Dealer
information
Add as waypoint
.
Sending vehicle data
1
Vehicle data are sent to a central Volvo database
(not your dealer) from which Volvo dealers can
retrieve vehicle information using the car's identi-
fication number (VIN
3
). The number is printed in
the car's service and warranty booklet, alterna-
tively inside the windscreen's bottom left-hand
corner.
–
Select
Service & repair
Send car data
.
Booking information and vehicle data
When you decide to book a service from your car,
the booking information and vehicle data will be
sent. Vehicle data information consists of infor-
mation within the following areas:
1
Applies to certain markets.
2
Applies to Sensus Navigation.
3
Vehicle Identification Number
||
MAINTENANCE AND SERVICE
340
•
service requirement
•
function status
•
fluid levels
•
meter reading
•
the car's vehicle identification number (VIN
3
)
•
the car's software version.
Related information
•
3
Vehicle Identification Number
||
MAINTENANCE AND SERVICE
342
Jacking points (arrows) for the jack that belongs to the car and lifting points (marked in red).
If the car is raised with a front workshop jack
then this must be positioned under one of the
two lifting points furthest in under the car. If the
car is raised with a rear workshop jack then it
must be positioned under one of the lifting
points. Ensure that the workshop jack is posi-
tioned so that the car cannot slide off the jack.
Always use axle stands or similar.
If the car is raised with a two-pillar workshop lift
then the front and rear lifting arms can be posi-
tioned under the outer lifting points (jacking
points). Alternatively, the inner lifting points can
be used at the front.
Related information
•
MAINTENANCE AND SERVICE
}}
343
Bonnet - opening and closing
The bonnet can be opened when the handle in
the passenger compartment has been turned
clockwise and the lock by the radiator grille has
been moved to the left.
The handle for bonnet opening is always on the left-
hand side.
Turn the handle about 20-25 degrees clock-
wise. You will hear when the catch releases.
Move the catch to the left and open the bon-
net. (The catch hook is located between the
headlamp and radiator grille, see illustration.)
WARNING
Check that the bonnet locks properly when
closed.
Related information
•
Engine compartment - checking (p. 344)
•
Engine compartment - overview (p. 343)
Engine compartment - overview
The overview shows some service-related com-
ponents.
Engine compartment
The appearance of the engine compartment may differ
depending on model and engine variant.
Coolant expansion tank
Washer fluid filler pipe
Radiator
Engine oil filler pipe
Reservoir for brake and clutch fluid (located
on the driver's side)
Starter battery
Relay and fuse box
Air filter
||
MAINTENANCE AND SERVICE
344
WARNING
The ignition system has very high voltage and
output. The voltage in the ignition system is
highly dangerous. The car's electrical system
must always be in key position 0 when work is
being performed in the engine compartment;
see Key positions - functions at different lev-
els (p. 81).
Do not touch the spark plugs or ignition coil
when the car's electrical system is in key
position II or when the engine is hot.
Related information
•
Bonnet - opening and closing (p. 343)
•
Engine compartment - checking (p. 344)
Engine compartment - checking
Some oils and fluids should be checked at regu-
lar intervals.
Regular checking
Check the following oils and fluids at regular
intervals, e.g. when refuelling:
•
Coolant
•
Engine oil
•
Washer fluid
WARNING
Remember that the radiator fan (located at
the front of the engine compartment, behind
the radiator) may start automatically some
after the engine has been switched off.
Always have the engine cleaned by a work-
shop - an authorised Volvo workshop is rec-
ommended. There is a risk of fire if the engine
is hot.
Related information
•
Bonnet - opening and closing (p. 343)
•
Engine compartment - overview (p. 343)
•
•
Engine oil - checking and filling (p. 345)
•
Washer fluid - filling (p. 359)
Engine oil - general
An approved engine oil must be used in order
that the recommended service intervals can be
applied.
Volvo recommends:
MAINTENANCE AND SERVICE
}}
345
When driving under adverse conditions, see
Engine oil - adverse driving conditions (p. 390).
In order to fulfil the requirements for the
engine's service intervals all engines are filled
with a specially adapted synthetic engine oil
at the factory. The choice of oil has been
made very carefully with regard to service life,
starting characteristics, fuel consumption and
environmental impact.
An approved engine oil must be used in order
that the recommended service intervals can
be applied. Only use a prescribed grade of oil
for both filling and oil change, otherwise you
will risk affecting service life, starting charac-
teristics, fuel consumption and environmental
impact.
Volvo Car Corporation disclaims all warranty
liability if engine oil of the prescribed grade
and viscosity is not used.
Volvo recommends that oil changes are car-
ried out at an authorised Volvo workshop.
Volvo uses different systems for warning of low/
high oil level or low oil pressure. Certain engine
variants have an oil pressure sensor, and then the
combined instrument panel's warning symbol for
low oil pressure is used
. Other variants
have an oil level sensor, when the driver is
informed via the instrument's warning symbol
and display texts. Certain variants have
both systems. Contact a Volvo dealer for more
information.
Change the engine oil and oil filter in accordance
with the intervals specified in the Service and
Warranty Booklet.
Using oil of a higher than specified grade is per-
mitted. If the car is driven in adverse conditions,
Volvo recommends using an oil of a higher grade
than the one specified, see Engine oil - adverse
driving conditions (p. 390).
For filling capacities, see Engine oil - grade and
volume (p. 391).
Related information
•
Engine oil - checking and filling (p. 345)
Engine oil - checking and filling
The oil level is detected with the electronic oil
level sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст