Audi TT (2007 year). Manual — part 12
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Disengage fuel hose -3- at bracket.
– Pull off bracket for fuel lines towards right -arrow- and move
clear to one side.
– Unplug electrical connector -1- at supplementary fuel pump -
V393- .
– Remove bolts -2- and -4-, detach bracket with supplementary
fuel pump -V393- and move clear to one side.
– Loosen bolt -1-.
– Remove nut -2- and bolt -3-.
– Detach hose retainer -arrow- from fuel filter and move fuel filter
-8- clear to one side with fuel hoses -4 ... 7- connected.
The following specifications must be obtained:
• There must be a distance of -a- = 13.5 mm between engine
support -2- and longitudinal member (right-side).
• The side of the engine support casting -2- must be aligned
parallel to the support arm -1- (distance -x- = distance -x-).
Note
Distance -a- = 13.5 mm can also be checked with a metal rod of
suitable size, or similar.
– If the distance measured is too large or small, the assembly
.
Assembling
Installation is carried out in the reverse order; note the following:
– Install fuel filter and supplementary fuel pump -V393- ⇒ Rep.
Gr. 20 .
5.3
Adjusting assembly mountings
Special tools and workshop equipment required
5. Assembly mountings
39
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
♦ Support bracket -10 - 222 A-
Procedure
• Tightening torques
– Remove engine cover panel -arrows-.
– Disengage fuel hose -3- at bracket.
– Pull off bracket for fuel lines towards right -arrow- and move
clear to one side.
– Unplug electrical connector -1- at supplementary fuel pump -
V393- .
– Remove bolts -2- and -4-, detach bracket with supplementary
fuel pump -V393- and move clear to one side.
– Loosen bolt -1-.
– Remove nut -2- and bolt -3-.
– Detach hose retainer -arrow- from fuel filter and move fuel filter
-8- clear to one side with fuel hoses -4 ... 7- connected.
40
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
housing.
– Position support bracket -10 - 222 A- with spindles -10 - 222
A /11- on bolted flanges of wing panels as shown in illustration.
– Attach hooks of spindles to engine lifting eyes.
– Take up weight of engine/gearbox assembly evenly with both
spindles (do not raise assembly).
– Remove bolts -arrows- for assembly mounting (engine end)
one by one and renew (if they were not renewed when instal‐
ling engine).
– Initially fit bolts hand-tight.
– Remove bolts -arrows- for assembly mounting (gearbox end)
one by one and renew (if they were not renewed when instal‐
ling engine).
– Initially fit bolts hand-tight.
5. Assembly mountings
41
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Using assembly lever, adjust engine/gearbox assembly be‐
tween engine mounting and support arm -1- until specifica‐
tions listed below are attained:
• There must be a distance of -a- = 13.5 mm between engine
support -2- and longitudinal member (right-side).
• The side of the engine support casting -2- must be aligned
parallel to the support arm -1- (distance -x- = distance -x-).
Note
Distance -a- = 13.5 mm can also be checked with a metal rod of
suitable size, or similar.
– Tighten bolts for assembly mounting (engine end).
– Ensure that the edges of the support arm (on the gearbox as‐
sembly mounting) -1- and gearbox mounting -2- are parallel.
Gr. 20 .
42
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст