Ford F-650 / 750 (2022 year). Manual in english — page 18

Safety Practices

WARNING:

If your vehicle

is stuck in snow, mud or sand, do
not rapidly spin the tires;
spinning the tires can tear the
tire and cause an explosion. A
tire can explode in as little as
three to five seconds.

WARNING:

Do not spin the

wheels at over 34 mph
(55 km/h). The tires may fail and
injure a passenger or bystander.

Driving habits have a great deal
to do with your tire mileage and
safety.

•

Observe posted speed limits

•

Avoid fast starts, stops and
turns

•

Avoid potholes and objects on
the road

•

Do not run over curbs or hit the
tire against a curb when
parking

Highway Hazards

No matter how carefully you drive
there’s always the possibility that
you may eventually have a flat tire
on the highway. Drive slowly to the
closest safe area out of traffic.
This may further damage the flat
tire, but your safety is more
important.

If you feel a sudden vibration or
ride disturbance when driving, or
you suspect your tire or vehicle
has been damaged, immediately
reduce your speed. Drive with
caution until you can safely pull
off the road. Stop and inspect the
tires for damage. If a tire is
under-inflated or damaged,
deflate it, remove wheel and
replace it with your spare tire and
wheel. If you cannot detect a
cause, have the vehicle towed to
the nearest repair facility or tire
dealer to have the vehicle
inspected.

Tire and Wheel Alignment

A bad jolt from hitting a curb or
pothole can cause the front end
of your vehicle to become
misaligned or cause damage to
your tires. If your vehicle seems to
pull to one side when you’re
driving, the wheels may be out of
alignment. Have an authorized
dealer check the wheel alignment
periodically.

Wheel misalignment in the front
or the rear can cause uneven and
rapid treadwear of your tires and
should be corrected by an
authorized dealer. Front-wheel
drive vehicles and those with an
independent rear suspension may
require alignment of all four
wheels.

The tires should also be balanced
periodically. An unbalanced tire
and wheel assembly may result in
irregular tire wear.

281

Wheels and Tires

Tire Rotation

Note:

If your tires show uneven

wear ask an authorized dealer to
check for and correct any wheel
misalignment, tire imbalance or
mechanical problem involved
before tire rotation.

Note:

Your vehicle may be

equipped with a dissimilar spare
wheel and tire assembly. A
dissimilar spare wheel and tire
assembly is defined as a spare
wheel and tire assembly that is
different in brand, size or
appearance from the road tires and
wheels. If you have a dissimilar
spare wheel and tire assembly it is
intended for temporary use only
and should not be used in a tire
rotation.

Rotating your tires at the
recommended interval helps your
tires wear more evenly, providing
better tire performance and longer
tire life.

E142548

Rear-wheel drive vehicles

E161439

Dual rear wheel vehicles (six
tire rotation)

Note:

For vehicles with directional

tires marked by an arrow on the tire
sidewall, tire rotation is not
recommended.

If your vehicle is equipped with
dual rear wheels it is
recommended that the front and
rear tires (in pairs) be rotated only
side to side. We do not
recommend splitting up the dual
rear wheels. Rotate them side to
side as a set. After tire rotation,
inflation pressures must be
adjusted for the tires new
positions in accordance with
vehicle requirements.

282

Wheels and Tires

Sometimes irregular tire wear can
be corrected by rotating the tires.

USING SNOW CHAINS

WARNING:

Snow tires must be the

same size, load index, and speed rating
as those originally provided by Ford. Use
of any tire or wheel not recommended
by Ford can affect the safety and
performance of your vehicle, which could
result in an increased risk of loss of
vehicle control, vehicle rollover, personal
injury, and death. Additionally, the use
of non-recommended tires and wheels
could cause steering, suspension, axle,
transfer case, or power transfer unit
failure. It is also strongly advised to
follow the Ford recommended tire
inflation pressure found on the Safety
Compliance Certification Label (affixed
to either the door hinge pillar, door-latch
post, or the door edge that meets the
door-latch post, next to the driver’s
seating position), or Tire Label which is
located on the B-Pillar or the edge of the
driver door. Failure to follow the tire
pressure recommendations can cause
uneven treadwear patterns and
adversely affect the way your vehicle
handles.

The tires on your vehicle have all-weather
treads to provide traction in rain and snow.
However, in some climates, you may need
to use snow tires and cables. If you need
to use cables, it is recommended that steel
wheels (of the same size and
specifications) be used, as cables may chip
aluminum wheels.

Note:

The suspension insulation and

bumpers help prevent vehicle damage. Do
not remove these components from your
vehicle when using snow tires and chains.

Follow these guidelines when using snow
tires and chains:

•

If possible, avoid fully loading your
vehicle.

•

Use only SAE Class S chains.

•

Install chains securely, verifying that
the chains do not touch any wiring,
brake lines or fuel lines.

•

Drive cautiously. If you hear the chains
rub or bang against your vehicle, stop
and retighten the chains. If this does
not work, remove the chains to prevent
damage to your vehicle.

•

Remove the tire chains when they are
no longer needed. Do not use tire
chains on dry roads.

If you have any questions regarding snow
chains or cables, please contact your
authorized dealer.

CHANGING A ROAD WHEEL

If you get a flat tire while driving, do not
apply the brake heavily. Instead, gradually
decrease your speed. Hold the steering
wheel firmly and slowly move to a safe
place on the side of the road.

Tire Change Procedure

WARNING:

Do not work on your

vehicle when the jack is the only support
as your vehicle could slip off the jack.
Failure to follow this instruction could
result in personal injury or death.

283

Wheels and Tires

WARNING:

To help prevent your

vehicle from moving when changing a
wheel, shift the transmission into park
(P), set the parking brake and use an
appropriate block or wheel chock to
secure the wheel diagonally opposite to
the wheel being changed. For example,
when changing the front left wheel,
place an appropriate block or wheel
chock on the right rear wheel.

WARNING:

Do not get under a

vehicle that is supported by a jack.

WARNING:

Do not attempt to

change a tire on the side of the vehicle
close to moving traffic. Pull far enough
off the road to avoid the danger of being
hit when operating the jack or changing
the wheel.

Note:

Passengers should not remain in the

vehicle when the vehicle is being jacked.

Park on a level surface, set the parking
brake and activate the hazard flashers.

E142551

1.

Turn the engine off and block the wheel
that is diagonally opposite of the flat
tire using a wheel chock.

2. Loosen each wheel lug nut ½ turn

counterclockwise, but do not remove
them until the wheel is raised off the
ground.

3. Replace the flat tire with the spare tire,

making sure the valve stem is facing
outward on all front and inboard rear
wheels. If you are replacing the
outboard wheel, the valve stem must
be facing inward. Reinstall the lug nuts
until the wheel is snug against the hub.
Do not fully tighten the lug nuts until
the wheel has been lowered.

4. Lower the wheel and fully tighten the

lug nuts in the order shown below. See

Technical Specifications

(page 285).

5. Unblock the wheels.

E161441

1

3

4

2

7

6

5

8

8-lug nut torque sequence.

1

2

3

4

5

6

7

8

9

10

E169375

10-lug nut torque sequence.

284

Wheels and Tires

TECHNICAL SPECIFICATIONS

Wheel Lug Nut Torque Specifications

WARNING:

When you install a wheel, always remove any corrosion, dirt or foreign

materials present on the mounting surfaces of the wheel or the surface of the wheel
hub, brake drum or brake disc that contacts the wheel. Make sure to secure any fasteners
that attach the rotor to the hub so they do not interfere with the mounting surfaces of
the wheel. Installing wheels without correct metal-to-metal contact at the wheel
mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while
your vehicle is in motion, resulting in loss of vehicle control, personal injury or death.

lb.ft (Nm)

1

Bolt size

450–500 lb.ft (610–678 Nm)

M22 x 1.5

1

Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford

recommended replacement fasteners.

On vehicles equipped with single rear wheels, retighten the lug nuts to the specified torque
at 100 mi (160 km) after any wheel disturbance (such as tire rotation, changing a flat tire,
wheel removal).

On vehicles equipped with dual rear wheels, retighten the lug nuts to the specified torque
at 100 mi (160 km) and again at 500 mi (800 km) of new vehicle operation and after
any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal).

It is important to follow the proper wheel mounting and lug nut torque procedures.

E161443

On all two-piece flat wheel nuts,
apply one drop of motor oil
between the flat washer and the
nut. Do not apply motor oil to the
wheel nut threads or the wheel
stud threads.

E145950

Hub pilot bore

A

Inspect the wheel pilot hole and
mounting surface prior to installation.
Remove any visible corrosion or loose
particles.

285

Wheels and Tires

ENGINE SPECIFICATIONS - 6.7L DIESEL

6.7L V8 Diesel Engine

Engine

406 in³ (6,651 cm³)

Displacement.

Ultra Low Sulfur Diesel up to B20

Required fuel.

1-3-7-2-6-5-4-8

Firing order.

15.8:1

Compression ratio.

Drivebelt Routing

Single Alternator

E224819

Single Alternator With Air Brake
Compressor

E224825

Drivebelt closest to the engine.

A

Drivebelt furthest from the
engine.

B

286

Capacities and Specifications

Dual Alternator

E224820

Dual Alternator With Air Brake
Compressor

E224826

Drivebelt closest to the engine.

A

Drivebelt furthest from the
engine.

B

Note:

The belt routings show vehicles with

air conditioning. When vehicles do not have
air conditioning, an idler pulley is in place of
the A/C compressor.

ENGINE SPECIFICATIONS - 7.3L

7.3L V8 Engine

Engine

445 in³ (7,293 cm³)

Displacement.

Minimum 87 octane

Required fuel.

1-5-4-8-6-3-7-2

Firing order.

Coil near spark plug with spark plug wire

Ignition system.

0.049 in (1.25 mm) - 0.053 in (1.35 mm)

Spark plug gap.

10.5:1

Compression ratio.

287

Capacities and Specifications

Drivebelt Routing

Single Alternator

E305075

Drivebelt closest to the engine.

A

Drivebelt furthest from the
engine.

B

Dual Alternator

E298579

Drivebelt closest to the engine.

A

Drivebelt furthest from the
engine.

B

MOTORCRAFT PARTS - 6.7L DIESEL

Part Number

Component

FL-2051S

Engine oil filter.

1

FA-1909

Foam pre-filter.

FA-1923

Air filter.

FD-4637

Fuel filter kit (2 included - engine and frame
rail mounted).

FT-187

Transmission filter.

BH-31-XL

Two Batteries (standard)(1500 CCA).

BH-31-XT

Two Batteries (optional)(1800 CCA).

288

Capacities and Specifications

Part Number

Component

BH-31-XT

Three Batteries (optional)(2700 CCA).

WW-2248

Windshield wiper blade.

1

If a Motorcraft oil filter is not available, use an oil filter that meets industry performance

specification SAE/USCAR-36.

We recommend Motorcraft parts that are available at your authorized dealer or at
www.fordparts.com. We engineer the parts for your vehicle to meet or exceed our
specifications. Use of other parts could impact vehicle performance, emissions and
durability. Your warranty could be void for any damage related to use of other parts.

289

Capacities and Specifications

MOTORCRAFT PARTS - 7.3L

Motorcraft Part Number

Component

FA-1923

Air filter element.

BH-31-XT

One battery (standard)(900 CCA).

BH-31-XT

Two batteries (optional)(except for Limited
Series)(1800 CCA total).

FL-820-S

Engine oil filter.

1

SP-589

Spark plug.

FT-187

Transmission fluid filter.

WW-2248

Windshield wiper blade.

1

If a Motorcraft oil filter is not available, use an oil filter that meets industry performance

specification SAE/USCAR-36.

We recommend Motorcraft parts that are available at your authorized dealer or at
www.fordparts.com. We engineer these parts for your vehicle and to meet or exceed our
specifications. Use of other parts could impact vehicle performance, emissions and
durability. Your warranty could be void for any damage related to use of other parts.

290

Capacities and Specifications

BULB SPECIFICATION CHART

Replacement bulbs are specified in the
chart below. Headlamp bulbs must be
marked with an authorized “D.O.T.” for

North America and an “E” for Europe to
ensure lamp performance, light brightness
and pattern and safe visibility. The correct
bulbs will not damage the lamp assembly
or void the lamp assembly warranty and
will provide quality bulb illumination time.

Trade name

Number of Bulbs

Function

H13/9008

2

Headlamps

W5W

2

Side marker lamp - front

3157NA

2

Park/Turn lamp- front

3157

2

Tail/stop/turn/side marker

3157

2

Reverse

3157

1

License plate lamp

912

1

High-mount brake lamp

12V6W

2

Map lamp

578

3

Dome/reading lamps

2825

2

Interior visor lamp

2825

2

Mirror turn signal

2825

2

Mirror clearance lamp

194

5

Front clearance lamps and
front identification lamps

Note:

To replace instrument panel lights,

see an authorized dealer.

ENGINE OIL CAPACITY AND
SPECIFICATION - 6.7L DIESEL

Use oil that meets the defined
specification and viscosity grade.

If you do not use oil that meets the defined
specification and viscosity grade, it could
result in:
•

Component damage that your vehicle
warranty does not cover.

•

Longer engine cranking periods.

•

Increased emission levels.

•

Reduced vehicle performance.

•

Reduced fuel economy.

291

Capacities and Specifications

Engine Oil

We recommend Motorcraft motor oil for
your vehicle. If Motorcraft motor oil is not
available, use motor oil of the
recommended viscosity grade that meets
our specification WSS-M2C171-F1. You can
find the list of approved motor oils at
www.motorcraft.com.

Do not use engine oil additives as they
could lead to engine damage not covered
by your vehicle warranty.

The use of correct oil viscosities for diesel
engines is important for satisfactory
operation. Determine which oil viscosity
best suits the temperature range you
expect to encounter for the next service
interval from the SAE Viscosity Grades
chart.

Note:

An engine block heater is

recommended at temperatures below
–10°F (–23°C).

E327351

292

Capacities and Specifications

Capacities

Including the Oil Filter

Variant

15.0 qt (14.2 L)

All.

Materials

Specification

Name

WSS-M2C171-F1

Motorcraft® SAE 10W-30 Super Duty Diesel Motor
Oil(U.S.)
Motorcraft® Super Duty Motor Oil SAE 10W-30 /
Huile moteur Super Duty SAE 10W-30 Motor-
craft®(Canada)
XO-10W30-QSDF(U.S.)
CXO-10W30-LSD12(Canada)

Alternative Engine Oil for
Extremely Cold Climates

To improve engine cold start performance,
we recommend that you use the following
alternative engine oil in extremely cold
climates, where the ambient temperature
reaches -22.0°F (-30°C) or below.

Materials

Specification

Name

WSS-M2C171-F1

Engine Oil - SAE 0W-40

Alternative Engine Oil for Biodiesel
Fuel Blends (B20 Max)

293

Capacities and Specifications

Materials

Specification

Name

WSS-M2C171-F1

Motorcraft® SAE 5W-40 Full Synthetic Diesel Motor
Oil(U.S.)
(Canada)
XO-5W40-5Q3SD(U.S.)

WSS-M2C171-F1

Motorcraft® SAE 15W-40 Super Duty Diesel Motor
Oil(U.S.)
Motorcraft® Super Duty Motor Oil SAE 15W-40 /
Huile moteur Super Duty SAE 15W-40 Motor-
craft®(Canada)
XO-15W40-QSDF(U.S.)
CXO-15W40-LSD12(Canada)

Alternative Engine Oil for Severe
Duty Service

Materials

Specification

Name

WSS-M2C171-F1

Motorcraft® SAE 5W-40 Full Synthetic Diesel Motor
Oil(U.S.)
(Canada)
XO-5W40-5Q3SD(U.S.)

ENGINE OIL CAPACITY AND
SPECIFICATION - 7.3L

Use oil that meets the defined
specification and viscosity grade.

If you do not use oil that meets the defined
specification and viscosity grade, it could
result in:
•

Component damage that your vehicle
warranty does not cover.

•

Longer engine cranking periods.

•

Increased emission levels.

•

Reduced vehicle performance.

•

Reduced fuel economy.

E142732

An oil that displays this symbol conforms
to current engine, emission system and
fuel economy performance standards of
ILSAC.

294

Capacities and Specifications

We recommend Motorcraft motor oil for
your vehicle. If Motorcraft oil is not
available, use motor oils of the
recommended viscosity grade that display
the API Certification Mark for gasoline

engines.

Do not use supplemental engine oil
additives because they are unnecessary
and could lead to engine damage that your
vehicle warranty does not cover.

Capacities

Including the Oil Filter

Variant

8.0 qt (7.57 L)

All.

Materials

Specification

Name

WSS-M2C961-A1

Motorcraft® SAE 5W-30 Synthetic Blend Motor
Oil(U.S.)
Motorcraft® SAE 5W-30 Super Premium Motor Oil
/ Huile moteur de très haute qualité SAE 5W-30
Motorcraft®(Canada)
XO-5W30-Q1SP(U.S.)
CXO-5W30-LSP6(Canada)

Alternative Engine Oil for
Extremely Cold Climates

To improve engine cold start performance,
we recommend that you use the following
alternative engine oil in extremely cold
climates, where the ambient temperature
reaches -22°F (-30°C) or below.

Materials

Specification

Name

WSS-M2C963-A1

Engine Oil - SAE 0W-30 - Synthetic Blend

295

Capacities and Specifications

E240523

COOLING SYSTEM CAPACITY
AND SPECIFICATION - 6.7L
DIESEL

Use coolant that meets the defined
specification.

If you do not use coolant that meets the
defined specification, it could result in:
•

Component damage that your vehicle
warranty does not cover.

•

Longer engine cranking periods.

•

Reduced vehicle performance.

Note:

We recommend an engine block

heater at temperatures below –10°F
(–23°C).

Capacities

Quantity

Variant

35.1 qt (33.2 L)

Primary cooling system.

15.1 qt (14.3 L)

Secondary cooling system.

Materials

Specification

Name

WSS-M97B57-A2

Motorcraft® Yellow Prediluted Antifreeze/
Coolant(U.S.)
Motorcraft® Yellow Prediluted Antifreeze/Coolant
/ Antigel/liquide de refroidissement prédilué jaune
Motorcraft®(Canada)
VC-13DL-G(U.S.)
CVC-13DL-G(Canada)

296

Capacities and Specifications