Ford Focus RS (2011 year). Instruction — part 121
E116815
8,5mm
10 mm
10 mm
G1202520en
501-26-
33
and Tolerance Checks
501-26-
33
DESCRIPTION AND OPERATION
Body - Hood Latch Panel
5mm
5mm
E116817
x2
Body - Front Fender
G1202520en
501-26-
34
and Tolerance Checks
501-26-
34
DESCRIPTION AND OPERATION
E116816
9 mm
• One hole has to be drilled for side skirt fixing.
WARNING: Due to the possible speed of
the Focus RS the side skirts on fender and
rocker panel must be fixed with clips
screws and tape! Do not cut any clips!
NOTE: Body side panels and parts for service will
already contain the required side skirt fixing holes.
ABS Sensor Bracket
G1202520en
501-26-
35
and Tolerance Checks
501-26-
35
DESCRIPTION AND OPERATION
E117470
1
2
Description
Item
Focus RS
1
Focus
2
The ABS sensor bracket is riveted to the front side
member. On Focus RS the bracket is mounted in
driving direction.
WARNING: If the ABS sensor bracket is
not mounted as shown, the ABS sensor
cable could detach from bracket!
G1202520en
501-26-
36
and Tolerance Checks
501-26-
36
DESCRIPTION AND OPERATION
Underbody Tolerance Check
1. Body dimensions, 3-, 4- and 5-door (quick
measurements using the Allvis system)
• All dimensions are measured from the middle
of the hole or bolt head or from the edge of
the panel, using the Allvis system, with
component assemblies installed.
• A tolerance of ± 3 mm applies to all specified
dimensions. All detailed illustrations
correspond to the left-hand side of the
vehicle.
Allvis specifications
Height setting of the test
probes
Adaptor
Point of measurement
350 mm
25 mm (probe)
1
240 mm
25 mm (probe)
2
160 mm
25 mm (probe)
3
110 mm
25 mm (probe)
4
50 mm
35 mm (probe)
5
240 mm
25 mm (probe)
6
310 mm
25 mm (probe)
7
G371029en
501-26-
37
and Tolerance Checks
501-26-
37
GENERAL PROCEDURES
1
2
3
5
6
7
4
0
1
0
6
7
3
4
E55020
1928
1468
1173
997
1670
1064
1438
2006
1566
1294
1177
1820
1203
1762
2
5
2. Body dimensions, 3-, 4- and 5-door
• All dimensions are measured starting from
the centre of each hole, using an electronic
measuring system and with the assemblies
removed.
• A tolerance of ± 3 mm applies to all specified
dimensions. All detailed illustrations
G371029en
501-26-
38
and Tolerance Checks
501-26-
38
GENERAL PROCEDURES
correspond to the left-hand side of the
vehicle.
E43251
140
14
13
12
11
10
9
8
7
6
5
4
3
2
1
350
622
984
634
423
1275
1338
1556
1563
1720
2070
2541
962
942
720
524
1214
431
1379
306
1378
1024
1096
987
988
961
1
2
4
3
5
6
7
14
11
10
9
8
12
13
3. Body dimensions, wagon (quick
measurements using the Allvis system)
• All dimensions are measured from the middle
of the hole or bolt head or from the edge of
G371029en
501-26-
39
and Tolerance Checks
501-26-
39
GENERAL PROCEDURES
the panel, using the Allvis system, with
component assemblies installed.
• A tolerance of ± 3 mm applies to all
measurements given. All detailed illustrations
correspond to the left-hand side of the
vehicle.
Allvis specifications
Height setting of the test
probes
adapter
Point of measurement
350 mm
25 mm (probe)
1
240 mm
25 mm (probe)
2
160 mm
25 mm (probe)
3
110 mm
25 mm (probe)
4
50 mm
35 mm (probe)
5
260 mm
25 mm (probe)
6
400 mm
25 mm (probe)
7
400 mm
25 mm (probe)
8
G371029en
501-26-
40
and Tolerance Checks
501-26-
40
GENERAL PROCEDURES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст