Ford Focus RS (2011 year). Instruction — part 103
Restraints Control Module (RCM)
General Equipment
Worldwide diagnostic system (WDS)
WARNINGS:
To avoid accidental deployment, the
restraints control module (RCM) backup
power supply must be depleted. Wait at
least one minute after disconnecting the
battery ground cable(s) before
commencing any repair or adjustment to
the supplemental restraint system (SRS),
or any component(s) adjacent to the SRS
sensors. Failure to follow these
instructions may result in personal injury.
To minimize the possibility of premature
deployment, do not use radio key code
savers when working on the supplemental
restraint system. Failure to follow this
instruction may result in personal injury.
Never probe the electrical connectors of
air bag modules or any other supplemental
restraint system component. Failure to
follow this instruction may result in
personal injury.
1. Disconnect the battery ground cable.
Mounting and Cables, General Procedures).
2. Remove the floor console. For additional
information, refer to:
Console, Removal and Installation),
Instrument Panel and Console, Removal
and Installation).
3. Remove the components in the order
indicated in the following illustration(s) and
table(s).
TIE39632
3
1
10 Nm
2
G296347en
501-20B-
128
Supplemental Restraint System
501-20B-
128
REMOVAL AND INSTALLATION
For additional information, refer to:
Battery
Disconnect and Connect
(414-01 Battery,
Floor Console
(501-12 Instrument Panel and
Floor Console - Vehicles Built From: 03/2007,
Vehicles With
:
Center Armrest
(501-12
Description
Item
Electrical connectors
1
Retaining bolts
2
Restraints control module
3
All vehicles
4. To install, reverse the removal procedure.
5.
WARNING: A new restraints control
module must be configured following
installation. Failure to follow this instruction
may result in personal injury.
When a new restraints control module is
installed, configure the restraints control
Vehicles with global closing
6. Initialize the door window motors.
Frames and Mechanisms, General
Procedures).
G296347en
501-20B-
129
Supplemental Restraint System
501-20B-
129
REMOVAL AND INSTALLATION
module using WDS
.
Window Motor Initialization
(501-11 Glass,
For additional information, refer to:
Door
Driver Air Bag Module
WARNINGS:
To avoid accidental deployment, the
restraints control module (RCM) backup
power supply must be depleted. Wait at
least one minute after disconnecting the
battery ground cable(s) before
commencing any repair or adjustment to
the supplemental restraint system (SRS),
or any component(s) adjacent to the SRS
sensors. Failure to follow these
instructions may result in personal injury.
Always wear safety glasses when working
on an air bag equipped vehicle and when
handling an air bag module. Failure to
follow this instruction may result in
personal injury.
To minimize the possibility of premature
deployment, do not use radio key code
savers when working on the SRS. Failure
to follow this instruction may result in
personal injury.
To minimize the possibility of injury in the
event of premature deployment, always
carry a live air bag module with the bag
and trim cover pointed away from the body.
Failure to follow this instruction may result
in personal injury.
To minimize the possibility of premature
deployment, live air bag modules must
only be placed on work benches which
have been ground bonded and with the
instructions may result in personal injury.
Never probe the electrical connectors of
air bag modules or any other SRS
component. Failure to follow this
instruction may result in personal injury.
Painting over the driver air bag module trim
cover or instrument panel could lead to
deterioration of the trim cover and air bags.
Do not for any reason attempt to paint
discolored or damaged air bag module trim
covers or instrument panel. Install a new
component. Failure to follow this
instruction may result in personal injury.
1. Disconnect the battery ground cable.
Mounting and Cables, General Procedures).
2. Remove the components in the order
indicated in the following illustration(s) and
table(s).
G391265en
501-20B-
130
Supplemental Restraint System
501-20B-
130
REMOVAL AND INSTALLATION
trim cover facing up. Failure to follow these
For additional information, refer to:
Battery
Disconnect and Connect
(414-01 Battery,
E48257
1
2
Description
Item
Steering column upper shroud
1
Driver air bag module
2
All vehicles
3. To install, reverse the removal procedure.
Vehicles with global closing
4. Initialize the door window motors.
Frames and Mechanisms, General
Procedures).
Removal Details
Item 1
Steering column upper shroud
1. NOTE: Turn the steering wheel to access the
steering column upper shroud retaining
clips.
Remove the steering column upper shroud
(steering wheel shown removed for clarity).
• Using a thin bladed screwdriver, release the
retaining clips.
TIE0027425
G391265en
501-20B-
131
Supplemental Restraint System
501-20B-
131
REMOVAL AND INSTALLATION
See Removal Detail
See Removal Detail
Window Motor Initialization
(501-11 Glass,
For additional information, refer to:
Door
Item 2
Driver air bag module
1. NOTE: Turn the steering wheel to access the
driver air bag module retaining clips.
Using a thin bladed screwdriver, detach the
driver air bag module from the steering wheel
(steering wheel shown removed for clarity).
• Release the spring clip.
E48258
2.
WARNING: The driver air bag module
should only be inverted long enough to
disconnect the driver air bag module
electrical connector. Handle with extreme
care making sure that, if for any reason this
procedure is interrupted, the driver air bag
module is turned the correct way up, with
the trim cover side uppermost. Failure to
follow these instructions may result in
personal injury.
Invert the driver air bag module to access
the driver air bag module wiring harness.
TIE42748
3. NOTE: It may be necessary to use a pair of
pointed nose pliers to release the driver air
bag module electrical connector locking
tangs.
Disconnect the driver air bag module
electrical connector.
• Disconnect the driver air bag module ground
cable (if equipped).
E48259
G391265en
501-20B-
132
Supplemental Restraint System
501-20B-
132
REMOVAL AND INSTALLATION
Passenger Air Bag Module — Vehicles Built From: 04/2006
Removal
WARNINGS:
The supplemental restraint system (SRS)
is active for a certain length of time after
the power supply has been disconnected.
Wait for a minimum of 3 minutes before
disconnecting or removing any SRS
components.
Wear safety goggles.
Make sure that the vehicle electrical
system is fully depowered and no other
power source is connected.
Do not probe supplemental restraint
system (SRS) electrical connectors.
(100-00 General Information, Description
and Operation).
NOTE: Removal steps in this procedure may
contain installation details.
1. Remove the instrument panel.
Panel and Console, Removal and Installation).
2. Torque: 8 Nm
E76529
x6
Installation
1. To install, reverse the removal procedure.
G851460en
501-20B-
133
Supplemental Restraint System
501-20B-
133
REMOVAL AND INSTALLATION
(SRS)
Health and Safety Precautions
Refer to:
Instrument Panel
(501-12 Instrument
Refer to
:
Supplemental Restraint System
Side Air Bag Module
WARNINGS:
Always wear safety glasses when working
on an air bag equipped vehicle and when
handling an air bag module. Failure to
follow this instruction may result in
personal injury.
To minimize the possibility of premature
deployment, do not use radio key code
savers when working on the supplemental
restraint system. Failure to follow this
instruction may result in personal injury.
To minimize the possibility of injury in the
event of premature deployment, always
carry a live air bag module with the bag
Failure to follow this instruction may result
in personal injury.
To minimize the possibility of premature
deployment, live air bag modules must
only be placed on work benches which
have been ground bonded and with the
trim cover facing up. Failure to follow these
instructions may result in personal injury.
Never probe the electrical connectors of
air bag modules or any other supplemental
restraint system component. Failure to
follow this instruction may result in
personal injury.
1. Disconnect the battery ground cable.
Mounting and Cables, General Procedures).
2. Remove the front seat backrest cover. For
additional information, refer to: (501-10
Seating)
Installation),
3. Remove the components in the order
table(s).
G296350en
501-20B-
134
Supplemental Restraint System
501-20B-
134
REMOVAL AND INSTALLATION
For additional information, refer to:
Battery
Front Seat Backrest Cover - 2.5L Duratec-RS
Disconnect and Connect
(414-01 Battery,
(224kW/305PS) - VI5
(Removal and
indicated in the following illustration(s) and
Front Seat Backrest Cover - 2.5L Duratec-ST
and trim cover pointed away from the body.
(VI5)
(Removal and Installation).
TIE39629
3
1
5 Nm
2
Description
Item
Side air bag module wiring harness
1
Side air bag module retaining nuts
2
Side air bag module
3
All vehicles
4. To install, reverse the removal procedure.
5. Initialize the door window motors.
Frames and Mechanisms, General
Procedures).
Removal Details
G296350en
501-20B-
135
Supplemental Restraint System
501-20B-
135
REMOVAL AND INSTALLATION
Window Motor Initialization
(501-11 Glass,
Vehicles with global closing
For additional information, refer to:
Door
See Removal Detail
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст