Ford Focus RS (2011 year). Instruction — part 83
SECTION 501-19 Bumpers
PAGE
CONTENTS
SPECIFICATIONS
501-19-2
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION
501-19-3
(43 423 0)
Front Bumper. . . . . . . . . . . . . . . . . . . . . . . . ..
501-19-6
Front Bumper Cover — 2.5L Duratec-ST (VI5). . . . . . . . . . . . . . . . ..
501-19-9
Rear Bumper Cover — 2.5L Duratec-ST (VI5). . . . . . . . . . . . . . . . ...
501-19-
Bumpers
501-19-
1
.
VEHICLE APPLICATION:
Torque Specifications
lb-in
lb-ft
Nm
Item
-
18
25
Front bumper retaining bolts
-
15
20
Rear bumper retaining bolts
-
18
25
Radiator support bracket retaining bolts
-
17
23
Radiator grille opening panel reinforcement
retaining bolts
-
18
25
Horn bracket retaining bolt
80
-
9
Intake air resonator retaining bolt
G167729en
501-19-
2
Bumpers
501-19-
2
SPECIFICATIONS
Front Bumper(43 423 0)
Removal
1. Remove the front bumper cover.
2. Remove the radiator splash shield.
TIE40814
3. Disconnect the power steering pump
electrical connectors.
TIE0036331
4. Detach the power steering pump support
bracket from the bumper.
TIE40815
25 Nm
5. Disconnect the air temperature sensor
electrical connector.
TIE40821
6. Remove the air temperature sensor.
G167732en
501-19-
3
Bumpers
501-19-
3
REMOVAL AND INSTALLATION
• Release the clip.
TIE41002
7. Remove the horn and bracket assembly.
1. Disconnect the electrical connector.
2. Remove the bolt.
TIE40818
1
25 Nm
2
8. Detach the wiring harness from the bumper
on both sides (left-hand side shown).
• Detach the clips.
TIE40816
9. Remove the air deflector on both sides
(left-hand side shown).
TIE40823
10. Detach the radiator grille opening panel
reinforcement from the bumper on both
sides (right-hand side shown).
TIE40824
23 Nm
11. Detach the intake air resonator from the
bumper.
TIE40825
9 Nm
12. Support the radiator on both sides
(left-hand side shown).
G167732en
501-19-
4
Bumpers
501-19-
4
REMOVAL AND INSTALLATION
• Using cable ties, secure the radiator to the
radiator grille opening panel reinforcement.
TIE41773
13. Detach the radiator support bracket from
the bumper on both sides (left-hand side
shown).
TIE40826
25 Nm
14. Remove the bumper.
TIE40827
Installation
1. To install, reverse the removal procedure.
G167732en
501-19-
5
Bumpers
501-19-
5
REMOVAL AND INSTALLATION
Front Bumper Cover — 2.5L Duratec-ST (VI5)
Removal
NOTE: Removal steps in this procedure may
contain installation details.
1. Remove the headlamp assemblies.
Lighting, Removal and Installation).
2.
E51246
3.
TIE40380
1
2
4.
TIE0032460
1
2
5.
TIE39201
6.
TIE0015188
7.
E66083
G545206en
501-19-
6
Bumpers
501-19-
6
REMOVAL AND INSTALLATION
Refer to:
Headlamp Assembly
(417-01 Exterior
8.
TIE40382
9.
TIE40383
10.
E65133
1
2
11.
E65135
x15
12.
E65134
13.
E65136
G545206en
501-19-
7
Bumpers
501-19-
7
REMOVAL AND INSTALLATION
14.
E65137
Installation
1. To install, reverse the removal procedure.
G545206en
501-19-
8
Bumpers
501-19-
8
REMOVAL AND INSTALLATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст