Ford Galaxy / Ford S-MAX. Manual — part 24
CHECK for the DTC. If the DTC is present,
INSTALL new rear shock absorbers.
REFER to:
Rear Shock Absorber
(204-02 Rear
Suspension, Removal and Installation).
TEST the system for normal operation.
C110F4B Right front shock absorber
solenoid - over temperature
Solenoid
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL new rear shock absorbers.
REFER to:
Rear Shock Absorber
(204-02 Rear
Suspension, Removal and Installation).
TEST the system for normal operation.
C110F78 Right front shock absorber
solenoid - alignment or
adjustment incorrect
Solenoid
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL new rear shock absorbers.
REFER to:
Rear Shock Absorber
(204-02 Rear
Suspension, Removal and Installation).
TEST the system for normal operation.
C111C11
Left front vertical
acceleration sensor circuit -
short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
G.
C111C12
Left front vertical
acceleration sensor circuit -
short to power
Circuit(s)
or sensor
GO to Pinpoint Test
H.
C111C13
Left front vertical
acceleration sensor circuit -
open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
I.
C111C29
Left front vertical
acceleration sensor circuit
signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new vertical acceleration sensor.
REFER to:
Vehicle Front Vertical
Accelerometer
(204-05 Vehicle Dynamic
Suspension, Removal and Installation).
TEST the system for normal operation.
C111D11
Right front vertical
acceleration sensor circuit -
short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
G.
C111D12
Right front vertical
acceleration sensor circuit -
short to power
Circuit(s)
or sensor
GO to Pinpoint Test
H.
C111D13
Right front vertical
acceleration sensor circuit -
open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
I.
C111D29
Right front vertical
acceleration sensor circuit
signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new vertical acceleration sensor.
REFER to:
Vehicle Front Vertical
Accelerometer
(204-05 Vehicle Dynamic
Suspension, Removal and Installation).
TEST the system for normal operation.
C111E11
Left rear vertical
acceleration sensor circuit -
short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
G.
C111E12
Left rear vertical
acceleration sensor circuit -
short to power
Circuit(s)
or sensor
GO to Pinpoint Test
H.
C111E13
Left rear vertical
acceleration sensor circuit -
open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
I.
C111E29
Left rear vertical
acceleration sensor circuit
signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new vertical acceleration sensor.
REFER to:
Vehicle Rear Vertical Accelerometer
(204-05 Vehicle Dynamic Suspension,
Removal and Installation).
TEST the system for normal operation.
C112B94 Suspension system switch -
unexpected operation
Switch
INSTALL a new suspension mode selection
switch. TEST the system for normal operation.
C112C11 Mode indicator 1 (comfort)
circuit - short to ground
Circuit(s)
or switch
GO to Pinpoint Test
M.
C112C12 Mode indicator 1 (comfort)
circuit - short to power
Circuit(s)
or switch
GO to Pinpoint Test
N.
C112C13 Mode indicator 1 (comfort)
circuit - open circuit
Circuit(s)
or switch
GO to Pinpoint Test
O.
C112D11 Mode indicator 2 (normal)
circuit - short to ground
Circuit(s)
or switch
GO to Pinpoint Test
M.
C112D12 Mode indicator 2 (normal)
circuit - short to power
Circuit(s)
or switch
GO to Pinpoint Test
N.
C112D13 Mode indicator 2 (normal)
circuit - open circuit
Circuit(s)
or switch
GO to Pinpoint Test
O.
C112E11
Mode indicator 3 (sport)
circuit - short to ground
Circuit(s)
or switch
GO to Pinpoint Test
M.
C112E12
Mode indicator 3 (sport)
circuit - short to power
Circuit(s)
or switch
GO to Pinpoint Test
N.
C112E13
Mode indicator 3 (sport)
circuit - open circuit
Circuit(s)
or switch
GO to Pinpoint Test
O.
C1A0311
Left front height sensor
circuit - short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
J.
C1A0312
Left front height sensor
circuit - short to power
Circuit(s)
or sensor
GO to Pinpoint Test
K.
C1A0313
Left front height sensor
circuit - open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
L.
C1A0329
Left front height sensor
circuit signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new front suspension height
sensor.
REFER to:
Front Suspension Height Sensor
(204-05 Vehicle Dynamic Suspension,
Removal and Installation).
TEST the system for normal operation.
C1A0411
Right front height sensor
circuit - short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
J.
C1A0412
Right front height sensor
circuit - short to power
Circuit(s)
or sensor
GO to Pinpoint Test
K.
C1A0413
Right front height sensor
circuit - open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
L.
C1A0429
Right front height sensor
circuit signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new front suspension height
sensor.
REFER to:
Front Suspension Height Sensor
(204-05 Vehicle Dynamic Suspension,
Removal and Installation).
TEST the system for normal operation.
C1A0511
Left rear height sensor
circuit - short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
J.
C1A0512
Left rear height sensor
circuit - short to power
Circuit(s)
or sensor
GO to Pinpoint Test
K.
C1A0513
Left rear height sensor
circuit - open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
L.
C1A0529
Left rear height sensor
circuit signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new rear suspension height sensor.
REFER to:
Rear Suspension Height Sensor
(204-05 Vehicle Dynamic Suspension,
Removal and Installation).
TEST the system for normal operation.
C1A0611
Right rear height sensor
circuit - short to ground
Circuit(s)
or sensor
GO to Pinpoint Test
J.
C1A0612
Right rear height sensor
circuit - short to power
Circuit(s)
or sensor
GO to Pinpoint Test
K.
C1A0613
Right rear height sensor
circuit - open circuit
Circuit(s)
or sensor
GO to Pinpoint Test
L.
C1A0629
Right rear height sensor
circuit signal invalid
Sensor
Connect the Ford approved diagnostic tool
and clear the DTC. Carry out a road test for
approximately 15 to 20 km (9 to 12 miles)
using various road surfaces and conditions.
Using the Ford approved diagnostic tool
CHECK for the DTC. If the DTC is present,
INSTALL a new rear suspension height sensor.
REFER to:
Rear Suspension Height Sensor
(204-05 Vehicle Dynamic Suspension,
Removal and Installation).
TEST the system for normal operation.
U000100 High speed controller area
CAN
REFER to:
Communications Network
(418-00
network (CAN)
communication bus general
failure
Module Communications Network, Diagnosis
and Testing).
U010000
Lost communication with
the powertrain control
module (PCM)
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U012100
Lost communication with
the braking system control
module
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U012600
Lost communication with
the steering angle sensor
module
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U014000
Lost communication with
the generic electronic
module (GEM)
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U040168 Invalid data received from
the PCM
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U041868 Invalid data received from
the braking system control
module
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U042268 Invalid data received from
the GEM
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U042868 Invalid data received from
the steering angle sensor
CAN
REFER to:
Communications Network
(418-00
Module Communications Network, Diagnosis
and Testing).
U200A94
Control module internal
power - unexpected
operation
Adaptive
damping
module
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U200B94
Control module internal
power A - unexpected
operation
Adaptive
damping
module
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U200C94
Control module internal
power B - unexpected
operation
Adaptive
damping
module
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U200D11
Control module output
power A circuit - short to
ground
Circuit(s)
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U200D12
Control module output
power A circuit - short to
power
Circuit(s)
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U200E11
Control module output
power B circuit - short to
ground
Circuit(s)
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U200E12
Control module output
power B circuit - short to
power
Circuit(s)
INSTALL a new adaptive damping module.
TEST the system for normal operation.
U201011 Switch illumination circuit -
short to ground
Circuit(s)
or switch
GO to Pinpoint Test
P.
U201012 Switch illumination circuit -
short to power
Circuit(s)
or switch
GO to Pinpoint Test
Q.
U201013 Switch illumination circuit -
open circuit
Circuit(s)
or switch
GO to Pinpoint Test
R.
U201311
Switch circuit - short to
ground
Circuit(s)
or switch
GO to Pinpoint Test
S.
U201312
Switch circuit - short to
power
Circuit(s)
or switch
GO to Pinpoint Test
T.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст