Ford Galaxy / Ford S-MAX. Manual — part 68
DTC C2008.11: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
P.
*
DTC C2008.12: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
Q.
*
DTC C2008.13: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
R.
*
DTC C2008.16: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
S.
*
DTC C2008.17: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
T.
*
DTC C2008.18: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
O.
*
DTC C2008.19: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
U.
*
DTC C2008.1D: Left motor
fault
Parking brake
release actuator.
Circuit(s).
*
*
GO to Pinpoint Test
V.
*
DTC P061E.67: Internal control
module brake signal
performance
Brake pedal switch.
Central junction
box.
Circuit(s).
*
*
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
GO to Pinpoint Test
W.
*
DTC U0001.00: High speed
CAN bus
CAN bus.
*
GO to Pinpoint Test
X.
*
DTC U0100.00: Lost
communications with engine
control module (ECM)
ECM.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0101.00: Lost
communications with
transmission control module
(TCM) - Automatic vehicles
only
TCM.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0121.00: Lost
communications with ABS
ABS Module.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0140.00: Lost
communications with central
junction box (CJB)
CJB.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
REFER to:
Communications Network
*
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
DTC U0300.00: Internal
control module software
incompatibility
Electronic Parking
Brake (EPB) Module
software version.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
Update the EPB module software,
REFER to WDS. Configure the module.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures).
REPEAT the self-test, CLEAR the
DTCs.
*
Electronic Parking
Brake (EPB) Module
configuration.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures). REPEAT the self-test,
CLEAR the DTCs.
*
CJB.
*
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0401.68: Control module
Powertrain Control
Module (PCM).
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
Check the PCM DTCs, REFER to WDS.
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0418.68: Invalid data
received from brake system
control module
ABS Module.
Circuit(s).
*
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
Check the ABS module DTCs, REFER
to WDS.
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U0422.68: Invalid data
received from central junction
box (CJB)
CJB.
*
NOTE: Do not replace Parking Brake
Module or Parking Brake Release
Actuators.
Check the CJB DTCs,
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
GEM.
*
Check the GEM DTCs,
*
REFER to: Generic Electronic Module
(GEM) (419-10, Diagnosis and
Testing).
REPEAT the self-test, CLEAR the
DTCs.
DTC U2002.62: EPB Switch
fault
EPB Switch.
Circuit(s).
*
*
GO to Pinpoint Test
Y.
*
DTC U2002.64: EPB Switch
fault
EPB Switch.
*
Check the EPB switch is not stuck ON.
REPEAT the self-test, CLEAR the
DTCs. If the DTC remains, INSTALL a
new EPB switch.
REFER to:
Parking Brake Switch -
Vehicles With: Electronic Parking
Brake (EPB)
(206-05 Parking Brake
and Actuation, Removal and
Installation).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U2002.92: EPB Switch
fault
EPB Switch.
Circuit(s).
*
*
GO to Pinpoint Test
Y.
*
DTC U2016.05: Control module
main software
EPB Module.
Battery.
*
*
GO to Pinpoint Test
Z.
*
DTC U2100.00: Control module
EPB Module.
*
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
CONFIGURE the EPB module.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures).
REPEAT the self-test, CLEAR the
DTCs.
*
CJB.
*
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U2100.54: Initial
configuration not complete
Electronic parking
brake (EPB)
module.
*
CHECK the EPB module mounting.
REFER to: Parking Brake Module (206-
05 Parking Brake and Actuation,
Removal and Installation).
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
CONFIGURE the EPB module.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures).
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
Release the parking brake. Carry out
the Assembly Check, REFER to WDS.
Calibrate the longitudinal acceleration
sensor. REFER to WDS. REPEAT the
self-test, CLEAR the DTCs. If the DTC
remains, INSTALL a new EPB module.
REFER to: Parking Brake Module (206-
05 Parking Brake and Actuation,
Removal and Installation).
*
*
*
*
DTC U2101.00: Control module
configuration incompatible
Electronic parking
brake (EPB)
module.
*
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
CONFIGURE the EPB module.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures).
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
Update the EPB module software with
WDS. REPEAT the self-test, CLEAR the
DTCs.
*
*
CJB.
*
CONFIGURE the CJB.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures).
REPEAT the self-test, CLEAR the
DTCs.
CHECK the CAN bus.
REFER to:
Communications Network
(418-00 Module Communications
Network, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
*
DTC U3000.00: Control module
Electronic parking
brake (EPB)
module.
*
REPEAT the self-test, CLEAR the
DTCs. If the DTC remains, INSTALL a
new EPB module.
REFER to: Parking Brake Module (206-
05 Parking Brake and Actuation,
Removal and Installation).
REPEAT the self-test, CLEAR the
DTCs.
*
DTC U3000.13: Control module
Battery.
*
Check the battery. If necessary,
REFER to: Charging System (414-00
Charging System - General
Information, Diagnosis and Testing).
REPEAT the self-test, CLEAR the
DTCs.
*
Electronic parking
brake (EPB)
module.
Circuit(s).
*
*
GO to Pinpoint Test
AA.
*
DTC U3000.29: Control module
Electronic parking
brake (EPB)
module.
*
CHECK the EPB module mounting.
REFER to: Parking Brake Module (206-
05 Parking Brake and Actuation,
Removal and Installation).
REPEAT the self-test, CLEAR the
DTCs.
NOTE: Make sure that the most up-
to-date software version is installed
in WDS.
CONFIGURE the EPB module.
REFER to:
Module Configuration
(418-
01 Module Configuration, General
Procedures).
Calibrate the longitudinal acceleration
sensor. REFER to WDS. REPEAT the
self-test, CLEAR the DTCs. If the DTC
*
*
*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст