Ford Ranger EV (2001 year). Manual — part 136
414-03A-140
414-03A-140
High Voltage/Traction Battery
REMOVAL AND INSTALLATION (Continued)
Installation
1. The battery module replacement procedure also
contains the battery module installation.
2. Install battery modules 17-18.
•
Use the Battery Module Lifting Tool to
install the battery modules.
•
Install and tighten new battery module nuts
using the Battery Post Torque Wrench.
•
Install the separator plates.
•
Connect the heating element connectors.
•
Clip the connectors into the separator plate.
3. Fill the area around the high-voltage jumper
nuts with Nyogel.
Traction Battery Module — Modules 22-24
Special Tool(s)
Battery Module Lifting Tool
SR-10009
Battery Post Torque Wrench
307-026
414-03A-141
414-03A-141
High Voltage/Traction Battery
REMOVAL AND INSTALLATION (Continued)
Removal
1. Remove the battery control module (BCM).
2.
WARNING: The nominal voltage of
the traction battery is 312 volts. The buffer
zone must be set up and insulated rubber
gloves and a face shield must be worn.
Failure to follow these precautions may
result in severe personal injury or death.
Observe the EV-specific precautions. Refer to
1 Set up the buffer zone.
2 Test and wear the insulated rubber gloves.
3 Wear the face shield.
3. Remove battery modules 17-21.
•
Unclip and disconnect the heating element
electrical connectors.
•
Remove the separator plates.
•
Remove and discard the high-voltage jumper
retaining nuts.
•
Use the Battery Module Lifting Tool to
remove the battery modules.
4. Replace the faulty battery module(s). Refer to
Traction Battery Module Replacement
Installation
1. The battery module replacement procedure
contains the battery module installation.
2. Install battery modules 17-21.
•
Use the Battery Module Lifting Tool to
install the battery modules.
•
Install and tighten new battery module nuts
using the Battery Post Torque Wrench.
•
Install the separator plates.
•
Connect the heating element connectors.
•
Clip the connectors into the separator plate.
414-03A-142
414-03A-142
High Voltage/Traction Battery
REMOVAL AND INSTALLATION (Continued)
3. Fill the area around the high-voltage jumper
nuts with Nyogel.
Traction Battery Temperature Sensor — Modules 22-24
Removal
1. The #1 temperature sensor is located on the
negative side of the #17 traction battery
module. To remove the temperature sensor,
remove traction battery module #17. Refer to
Traction Battery Module — Modules17-18.
2. The #2 temperature sensor is located on the
negative side of the #6 traction battery module.
To remove the temperature sensor, remove
traction battery module #6. Refer to Traction
Battery Module — Modules17-18.
3. The #3 temperature sensor is located on the
positive side of the #26 traction battery module.
To remove the temperature sensor, remove
traction battery module #26. Refer to Traction
Battery Module — Modules 16, 25-27.
4. The #4 temperature sensor is located on the
positive side of the #31 traction battery module.
To remove the temperature sensor, remove
traction battery module #31. Refer to Traction
Battery Module — Modules 12-15, 28-31.
414-03A-143
414-03A-143
High Voltage/Traction Battery
REMOVAL AND INSTALLATION (Continued)
5.
CAUTION: Do not use excessive force
to remove the temperature sensor or damage
to the battery module may occur.
NOTE: If the sensor is difficult to remove,
warm it using a heat gun. Be careful not to
overheat the sensor or the battery module, or
damage to both may occur.
Remove the temperature sensor.
•
Pull the bottom of the temperature sensor
from the battery module and remove the
sensor.
Installation
1. Apply a thin coat of thermal grease to the back
of the thermistor.
2. The traction battery temperature sensors are
mounted on the side of the battery modules. To
install the temperature sensors, reverse the
removal procedure for the battery module on
which the sensor is located. Refer to the
appropriate Traction Battery Module procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст