Ford F150 Pickup. Instruction — part 406
Fig. 88: Identifying RABS Valve Harness Connector
Courtesy of FORD MOTOR CO.
VACUUM POWER BOOSTER
Removal & Installation
1. Remove the brake master cylinder. See MASTER CYLINDER .
2. Compress the clamp. Disconnect the power brake booster hose.
3. Remove the stoplight switch self-locking pin. See Fig. 30 .
4. Slide the stoplight switch and booster push rod off the brake pedal pin. See Fig. 31 .
5. Remove the bulkhead sound insulator. See Fig. 32 .
6. Remove the power brake booster nuts and remove booster. See Fig. 32 .
7. To install, reverse removal procedure.
WHEEL CYLINDERS (F150 HERITAGE PICKUP & F150 PICKUP)
Removal & Installation
1. Remove the brake shoes. See REAR BRAKE SHOES (F150 HERITAGE PICKUP & F150
2003 Ford Pickup F150
2002-04 BRAKES Disc & Drum - Blackwood, F150 Heritage Pickup & F150 Pickup
PICKUP) .
2. Disconnect the brake line fitting. See Fig. 89 .
3. Remove the two rear wheel cylinder bolts.
4. Remove the rear wheel cylinder.
5. To install, reverse removal procedure. Adjust brakes, and bleed hydraulic system. See BLEEDING
BRAKE SYSTEM .
Fig. 89: Removing Wheel Cylinder
Courtesy of FORD MOTOR CO.
OVERHAUL
CALIPER
Disassembly
NOTE:
Use same disassembly procedures for single and dual piston calipers.
WARNING:
DO NOT place fingers between wood and piston as piston leaves
caliper.
2003 Ford Pickup F150
2002-04 BRAKES Disc & Drum - Blackwood, F150 Heritage Pickup & F150 Pickup
1. Remove caliper. See FRONT BRAKE CALIPER & PADS or REAR DISC BRAKE CALIPERS &
PADS under REMOVAL & INSTALLATION. Drain fluid from caliper.
2. Secure caliper in a vise. Place a block of wood between caliper and piston(s). See Fig. 90 . Apply low air
pressure to brake hose inlet. Air pressure forces piston(s) outward.
3. If piston is jammed or seized and does not come out easily, use a brass hammer to lightly tap caliper
while applying air pressure. DO NOT pry piston from bore.
4. Remove and discard seals and boots.
Fig. 90: Removing Caliper Piston
Courtesy of FORD MOTOR CO.
2003 Ford Pickup F150
2002-04 BRAKES Disc & Drum - Blackwood, F150 Heritage Pickup & F150 Pickup
Cleaning & Inspection
1. Carefully clean rust and corrosion from caliper machined surfaces using a wire brush. DO NOT use wire
brush in caliper bores. Clean all components with isopropyl alcohol and dry with compressed air.
2. Inspect caliper bore, seal grooves and boot grooves for wear or damage. If bores are scored, corroded or
worn, replace caliper. Replace anti-rattle clip, caliper support spring and key.
Reassembly
1. Apply clean brake fluid to NEW piston seal, and install in caliper bore groove. Apply clean brake fluid to
caliper bore. Coat piston and outside beads of dust boot with clean brake fluid.
2. Push piston through boot until boot is around bottom (closed end) of piston. See Fig. 91 or Fig. 92 .
Position piston and boot directly over caliper bore. Spread dust boot over piston as it is installed.
3. With bead seated in groove, carefully press straight down on piston until it bottoms in caliper bore. DO
NOT cock or jam piston in caliper bore. If necessary, use a "C" clamp and a block of wood to bottom
piston in caliper bore.
Fig. 91: Exploded View Of Single Piston Caliper
Courtesy of FORD MOTOR CO.
CAUTION: Do not hone the caliper bores. Pistons are not available for honed caliper
bores.
2003 Ford Pickup F150
2002-04 BRAKES Disc & Drum - Blackwood, F150 Heritage Pickup & F150 Pickup
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст