Ford Falcon. Manual — part 399
419-10-24
Body Electronics Module (BEM)
419-10-24
DIAGNOSIS AND TESTING (Continued)
Pin Number(s)
Circuit Designation/Description
Normal Condition/Measurement
J6/12
(WHT)
Accesory
J6/13
(RD/BL)
Start circuit
J6/14
NC
J6/15
(BLK)
Pedal circuit ground
J6/16
(LT BL/BLK)
Pedal circuit Motor +
TILA 8 pin connector
Pin Number(s)
Circuit Designation/Description
Normal Condition/Measurement
J7/1
(YLW)
Pedal Circuit battery +
J7/3
(BLK)
Pedal circuit ground
J7/6
(LT BL/BLK)
Pedal circuit motor +
J7/8
(LT BL/ORG)
Pedal circuit motor -
Pinpoint Tests
PINPOINT TEST A : COURTESY LAMP DRIVER TEST
Test Step
Result / Action to Take
A1
Yes
Using WDS operate courtesy lamp drivers and monitor pin J3/12.
Return to sympton chart for next steps
Is pin low when drivers activated and high otherwise?
No
Go to A2
A2
Yes
Check wiring to pin J3/12. Is wiring OK?
Replace BEM
No
Fix wiring
G43561 en
419-10-25
Body Electronics Module (BEM)
419-10-25
DIAGNOSIS AND TESTING (Continued)
PINPOINT TEST B : HEATED BACKLIGHT TEST
Test Step
Result / Action to Take
B1
Yes
Using WDS monitor (BACKL_SW) when pressing ICC backlite switch.
Go to B2
Is input OK?
No
Check other probable causes on symptom chart.
B2
Yes
Turn on demist relay using WDS (HEAT_BCK)
Check other probable causes on symptom chart.
Check voltage at pin J2/10 is 0V.
No
Turn demist relay off using WDS.
Go to B3
Check voltage at pin J2/10 is 12V.
Are results OK?
B3
Yes
Check wiring to pin J2/10
Replace BEM
Is wiring OK?
No
Fix wiring
PINPOINT TEST C : IGNITION SWITCH VOLTAGE LEVELS
Test Step
Result / Action to Take
C1
Yes
Does Battery Accessory and Ignition and ground have
Return to symptom chart
appropriate voltage levels when key in relevant ignition position?
No
Check TILA and wiring
PINPOINT TEST D : IGNITION AND ACCESSORY LOW AT KEY OFF
Test Step
Result / Action to Take
D1
Yes
Does ignition and Accessories go low at Ignition Off?
Return to symptom chart
No
Check TILA and wiring
PINPOINT TEST E : POWER WINDOW SUPPLY
Test Step
Result / Action to Take
E1
Yes
Activate and deactivate BEM power window supply
(PID WIND_OS#)
Go to symptom chart.
No
Is the measured output voltage J2/11 as expected?
Go to E2
G43561 en
419-10-26
Body Electronics Module (BEM)
419-10-26
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
E2
Yes
Is wiring to pin J2/11 OK?
Change BEM
No
Fix wiring
PINPOINT TEST F : REMOTE RECEIVER OPERATION
Test Step
Result / Action to Take
F1
Yes
Connect WDS.
Go to symptom chart
Monitor status of PID TNSMT_CMD while pressing different buttons
on remote key.
No
Go to F2
Does PID status reflect last button pressed ?
F2
Yes
Take known good remote key and try and train it to the car
Original remote key was faulty. Replace original
Does BEM acknowledge receipt of key press as part of training
remote key.
procedure?
No
Go to F3
F3
Yes
Change receiver and take known good remote key and try and train it
Original receiver was faulty.
to the car
No
Does BEM acknowledge receipt of key press as part of training
Replace BEM and repeat step F2. If still
procedure?
unsuccessful then replace ICC (Internal ICC
wiring fault).
PINPOINT TEST G : DOOR LOCK INPUT
Test Step
Result / Action to Take
G1
Yes
Monitor voltage at pin J2/24 while locking and unlocking the drivers
Return to symptom chart
door.
No
Is voltage 0V when door unlocked and 12V when door locked?
Check wiring and door lock feedback on motor.
PINPOINT TEST H : BATTERY SAVER CIRCUIT NOT FUNCTIONING
Test Step
Result / Action to Take
H1
Yes
Ensure glovebox globe is present and operational
Battery saver circuit operating correctly. Return
Activate PID
BATTSAVRLY# command with Glove Box Door open
to symptom chart.
Does glove box lamp illuminate?
No
Go to H2
G43561 en
419-10-27
Body Electronics Module (BEM)
419-10-27
DIAGNOSIS AND TESTING (Continued)
Test Step
Result / Action to Take
H2
Yes
Using WDS activate and deactivate battery saver and monitor pin
Return to symptom chart.
J3/3.
No
Is voltage output as expected?
Go to H3
H3
Yes
Check wiring to pin J3/3. Is wiring OK?
Replace BEM
No
Fix wiring
PINPOINT TEST I : DOME LAMP NOT FUNCTIONING
Test Step
Result / Action to Take
I1
Yes
Turn off ignition.
Dome lamp operating correctly.
Monitor Personalizes settings TAXI_MODE, PANIC_ALR,
DTRIG_MOD, MDT_MOD, HAZ_WARN, HORN_WARN, BAT_SAV,
No
COURTESY.
Go to I2
Test 12V available on J3/3. Operate Dome switch on ICC.
Does Dome lamp operate?
I2
Yes
Select PID LR_AJAR, RR_AJAR
Return to symptom chart
Did dome lamp turn on?
No
Ground J3/12, Go to I3
I3
Yes
Does dome lamp light?
BEM fault
No
Wiring fault
PINPOINT TEST J : NO DEMIST FUNCTION
Test Step
Result / Action to Take
J1
Yes
Are DTC’s B1348 and B1349 present?
Follow fault finding chart for these codes
No
Go to J2
G43561 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст