Ford Falcon. Manual — part 432
501-14-7
Handles, Locks, Latches and Entry Systems
501-14-7
REMOVAL AND INSTALLATION (Continued)
4. Remove the actuator assembly while
Hood Latch Release Cable
disconnecting the latch rod.
Removal
5. Remove the latch assembly retaining screws and
remove the latch with connecting rod and
1. Remove hood latch.
courtesy lamp wiring lead attached.
2. Disconnect hood release handle from instrument
panel.
Item
Description
1
Latch assembly
Item
Description
2
Screw
1
Hood release handle
3
Courtesy lamp wiring
3. Pop out grommet on cowl side attached to cable.
4
Connecting rod
Installation
5
Liftgate body
1. Reverse removal procedure.
Installation
Decklid Latch and Emergency Release
1. Reverse removal procedure.
Cable
Liftgate Latch Striker
Removal
Removal
1. Remove decklid trim if fitted.(Refer to Section
501-05.)
1. Remove load floor carpet. (Refer to Section
501-05.)
2. Remove decklid latch nuts.
2. Remove liftgate latch striker bolts.
Item
Description
Item
Description
1
Decklid latch assembly
1
Liftgate striker
2
Nut
2
Bolt
3
Decklid body
Installation
1. Reverse removal procedure.
G31878 en
501-14-8
Handles, Locks, Latches and Entry Systems
501-14-8
REMOVAL AND INSTALLATION (Continued)
3. Disconnect emergency release cable.
Exterior Front Door Handle
Removal
1. Remove the interior door handle bezel and
window regulator handle.
2. Remove door trim. For additional information,
refer to Door Trim section.
3. Remove the door trim retaining screws, lift the
door trim panel from the door channel and
remove.
4. Remove the door watershield sufficiently to gain
access to door handle.
5. Remove the two bolts retaining the outer door
handle.
6. Unclip the latch rod, remove the door handle from
Item
Description
the door panel and remove door handle.
1
Emergency release cable
2
Actuating cable end
3
Emergency release pull tab
Installation
1. Reverse removal procedure.
Decklid Latch Striker
Removal
1. Remove cover lower back.(Refer to Section
501-05.)
2. Remove decklid latch striker bolts.
Item
Description
1
Front outer door handle
2
Lock retaining screw
3
Lock retainer
4
Screw - M6
Installation
1. Reverse removal procedure.
Exterior Rear Door Handle
Removal
1. Remove interior door handle bezel. Remove
Item
Description
window regulator handle.
1
Decklid striker
2. Remove door trim. For additional information,
2
Bolt
refer to Door Trim section.
3. Remove door trim retaining screws, lift the door
Installation
trim panel from the door channel and remove.
1. Reverse removal procedure.
4. Remove the door watershield sufficiently to gain
access to door handle.
G31878 en
501-14-9
Handles, Locks, Latches and Entry Systems
501-14-9
REMOVAL AND INSTALLATION (Continued)
5. Remove bolt retaining outer door handle, detach
4. Disengage handle assembly from door inner
handle from door panel and unclip door latch rod.
sheet metal by sliding rearwards and withdrawing
through trim.
Installation
1. Reverse removal procedure.
Ignition Lock
Removal
1. Insert the ignition key and turn it to the ’1’
position.
2. Depress the pin in the steering column lock
housing and withdraw the lock assembly.
3. Insert the ignition key and turn it to the ’1’
position.
4. Align the lock in the column housing, depress the
pin and push the lock into the housing until the pin
Item
Description
snaps into its locating hole.
1
Exterior rear door handle
2
Bolt
Installation
1. Reverse removal procedure.
Interior Door Handle
Removal
1. Remove
plug.
2. Remove screw attaching handle assembly to door
inner sheet metal.
Item
Description
1
Solenoid assembly
2
Solenoid retaining screw
Installation
1. Reverse removal procedure.
Interior Lock Button
Removal
NOTE: Lock button is not serviceable. Should a new
lock rod be required, a new lock button should be
Item
Description
fitted.
1
Interior door handle
Installation
2
Actuating cable
1. Door trim must be removed to gain access to lock
3
Screw
rod.
4
Button plug
3. Disconnect cable attaching handle to latch.
G31886 en
501-14-10
Handles, Locks, Latches and Entry Systems
501-14-10
REMOVAL AND INSTALLATION (Continued)
2. Push lock rod button firmly onto lock rod. Ensure
Grab Handles — Sedan
locating rib faces out.
Removal
1. Remove grab handles as shown in figure.
Item
Description
1
Lock button
Item
Description
3. Replace door trim, guiding lock button through
1
Grab handle
hole in door trim.
2
Screw
4. Ensure button is flush with trim in locked position.
Installation
5. Check for satisfactory operation of the lock.
1. Reverse removal procedure.
Grab Handles — Ute
Fuel Filler
Removal
Removal
1. Remove grab handles as shown in figure.
1. Open Luggage compartment.
2. Remove quarter trim.
3. Remove the two solenoid-retaining screws via the
fuel door.
Item
Description
1
Grab handle
2
Screw
Installation
Item
Description
1. Reverse removal procedure.
1
Fuel filler flap
2
Solenoid retaining screw
4. Remove solenoid and cable assembly.
Installation
1. Reverse removal procedure.
G31886 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст