Ford Falcon. Manual — part 431
501-14-3
Handles, Locks, Latches and Entry Systems
501-14-3
DESCRIPTION AND OPERATION
Latches
The decklid consists of the following components:
Decklid latch
Decklid striker
Decklid emergency release cable
The wagon liftgate consists of the following
components:
Liftgate latch and actuator
Liftgate striker
The hood consists of the following components:
Hood Latch
Hood latch release handle and cable
The fuel filler consists of the following components:
Solenoid Assembly
G31871 en
501-14-4
Handles, Locks, Latches and Entry Systems
501-14-4
GENERAL PROCEDURES
Wagon Liftgate Latch
NOTE: This latch consists of a primary latch position
designed to hold the liftgate firmly into the
weatherstrip section to preclude water leaks and/or
wind noise.
1. Ensure that the primary latch has been activated
when the liftgate is fully closed.
2. Adjust the liftgate latch striker pin as required to
establish a door-to-weatherstrip seal.
3. The striker can be adjusted fore/aft and sideways
by loosening the retaining bolts.
G31872 en
501-14-5
Handles, Locks, Latches and Entry Systems
501-14-5
REMOVAL AND INSTALLATION
3. Remove door trim panel retaining screws (4).
Hood Latch
Remove grab handle screws (2). Pull door trim
away from sheetmetal.
Removal
4. Remove the door watershield and Hip Bolster.
1. Open
bonnet.
5. Disengage latch rod from outer door handle and
2. Remove attaching screws and remove latch
the door locking rod from the lock barrel lever.
assembly from vehicle.
Item
Description
Item
Description
1
Screw
1
Front door latch and actuator assembly
2
Bonnet Latch assembly
2
Screw
3. Disconnect latch operating cable.
6. Disconnect interior handle cable from latch.
7. Remove the door latch retaining screws (Torx
head), remove the latch from the door.
Installation
1. With the latch actuating rods attached assemble
the latch into the door panel. Install the retaining
screws.
2. Connect interior handle cable to latch.
3. Connect the outer door handle and lock barrel
rods.
4. Make sure soldier button rod is fitted to latch
handle. Make sure soldier button is fitted to rod.
5. Refit the door watershield and Hip Bolster.
6. Install the door trim panel and refit the retaining
Item
Description
screws.
1
Latch operating cable
7. Install the interior door handle bezel and grab
2
Retaining clips
handle cap.
3
Bonnet latch assembly
Rear Door Latch
Installation
Removal
1. Reverse removal procedure.
1. Remove interior door handle. Remove window
Front Door Latch
regulator handle (where fitted).
2. Remove grab handle cap (where fitted).
Removal
3. Remove door trim retaining screws, pull the door
1. Remove the interior door handle bezel.
trim panel from the door channel and remove.
2. Remove grab handle cap.
4. Remove water shield.
G31875 en
501-14-6
Handles, Locks, Latches and Entry Systems
501-14-6
REMOVAL AND INSTALLATION (Continued)
5. Disconnect exterior door handle rod from latch
Door Latch Striker
and handle.
Removal
1. Remove striker as shown in figure.
Item
Description
1
Rear door latch and actuator assembly
Item
Description
2
Screw
1
Striker Assy. (1 per door)
6. Remove nuts retaining outer door handle, detach
2
Screw - M8x18 Csk Tx (x2 per door)
handle from door panel and disconnect door latch
rod.
Installation
7. Remove latch retaining screws (Torx head).
1. Reverse removal procedure.
Disconnect interior handle cable from latch and
remove latch from door.
Liftgate Latch and Actuator
Installation
Removal
1. Position latch into door panel, connect interior
1. Remove the liftgate interior trim panel.(Refer to
handle cable. Install retaining screws.
Section 501-05.)
2. Connect latch rod to outer door handle, position
2. Disconnect the wiring plug.
handle to door panel and install retaining nuts.
3. Refit door watershield.
4. Refit interior door trim panel and retaining screws.
5. Install interior door handle bezel, window
regulator handle and grab handle cap (where
fitted).
Item
Description
1
Actuator assembly
2
Lock barrel connecting rod
3
Lock barrel
4
Actuator to latch connecting rod
5
Latch assembly
6
Nut
3. Remove the liftgate actuator mechanism retaining
nuts and disconnect the lock barrel connecting
rod.
G31875 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст