Ford Falcon. Manual — part 483
501-20b-147
Occupant Restraints — Passive
501-20b-147
REMOVAL AND INSTALLATION (Continued)
adjusting or striking components near the
15. Move and tilt the front seats to their highest and
front or side airbag sensors, such as doors,
most forward position.
instrument panel, console, door latches,
WARNING: To avoid accidental
strikers, seats and hood latches.
deployment and possible personal injury, the
The side impact sensors (if equipped) are
backup power supply must be depleted before
located at or near the base of the B-pillars and
repairing or replacing any front or side airbag
C-pillars.
supplemental restraint system (SRS)
To deplete the backup power supply energy,
components and before servicing, replacing,
disconnect the battery ground cable and wait
adjusting or striking components near the
at least one minute. Be sure to disconnect
front or side airbag sensors, such as doors,
auxiliary batteries and power supplies (if
instrument panel, console, door latches,
equipped).
strikers, seats and hood latches.
10. Disconnect the battery ground cable and wait at
The side impact sensors (if equipped) are
least one minute. For additional information, refer
located at or near the base of the B-pillars and
to Section 414-01.
C-pillars.
11. Remove the restraint system diagnostic tool from
To deplete the backup power supply energy,
the vehicle harness side of the passenger airbag
disconnect the battery ground cable and wait
module electrical connector.
at least one minute. Be sure to disconnect
auxiliary batteries and power supplies (if
equipped).
16. Vehicles with power seats, disconnect the battery
ground cable and wait at least one minute. For
additional information, refer to Section 414-01.
17. From under the front RH seat, remove the
restraint system diagnostic tool from the safety
belt buckle pretensioner floor electrical connector.
12. Connect the passenger airbag module electrical
connector.
13. Close the glove compartment.
14. Connect the battery ground cable. For additional
information, refer to Section 414-01.
G12363 en
501-20b-148
Occupant Restraints — Passive
501-20b-148
REMOVAL AND INSTALLATION (Continued)
18. From under the front RH seat, connect the safety
Passenger Airbag Module
belt buckle pretensioner electrical connector.
Special Tool(s)
Diagnostic Tool, Restraint
System (2 req’d)
418-F395 (014-R1079)
Diagnostic Tool, Restraint
System (4 req’d)
418-F403
Item
Description
1
Seat belt pretensioners
Diagnostic Tool, Restraint
2
Pretensioner electrical connector
System (2 req’d)
418-F088 (105-R0012)
19. From under the front LH seat, remove the
restraint system diagnostic tool from the safety
belt buckle pretensioner floor electrical connector.
20. From under the front LH seat, connect the safety
belt buckle pretensioner electrical connector.
21. Connect the battery ground cable. For additional
Removal
information, refer to Section 414-01.
WARNING: Always wear safety glasses when
WARNING: The restraint system
repairing an airbag supplemental restraint system
diagnostic tool is for restraint system service
(SRS) vehicle and when handling an airbag
only. Remove from the vehicle prior to road
module. This will reduce the risk of injury in the
use. Failure to remove could result in injury
event of an accidental deployment.
and possible violation of vehicle safety
standards.
WARNING: Carry a live airbag module with
the airbag and deployment door pointed away
22. With all the restraint system diagnostic tools
from your body. This will reduce the risk of injury
removed, prove out the supplemental restraint
in the event of an accidental deployment.
system (SRS). For additional information, refer to
Airbag and Safety Belt Pretensioner Supplemental
Restraint System (SRS), in the Diagnosis and
WARNING: Do not set a live airbag module
Testing portion of this section.
down with the deployment door face down. This
will reduce the risk of injury in the event of an
accidental deployment.
WARNING: Carry a live airbag module
pointed away from your body. This will reduce the
risk of injury in the event of an accidental
deployment.
WARNING: After deployment, the airbag
surface can contain deposits of sodium
hydroxide, a product of the gas generant
combustion that is irritating to the skin. Wash
your hands with soap and water afterwards.
WARNING: Never probe the connectors on
the airbag module. Doing so can result in airbag
deployment, which can result in personal injury.
G12363 en
501-20b-149
Occupant Restraints — Passive
501-20b-149
REMOVAL AND INSTALLATION (Continued)
4. Remove instrument panel lower trim.
WARNING: Airbag modules with discolored
or damaged trim covers must be replaced, not
repainted.
WARNING: To avoid accidental deployment
and possible personal injury, the backup power
supply must be depleted before repairing or
replacing any front or side airbag supplemental
restraint system (SRS) components and before
servicing, replacing, adjusting or striking
components near the front or side airbag sensors,
such as doors, instrument panel, console, door
latches, strikers, seats and hood latches.
The side impact sensors (if equipped) are located
at or near the base of the B-pillars and C-pillars.
To deplete the backup power supply energy,
5. Remove 3 retaining screws from air register as
disconnect the battery ground cable and wait at
shown.
least one minute. Be sure to disconnect auxiliary
batteries and power supplies (if equipped).
NOTE: Repair is made by installing a new part only. If
the new part does not correct the condition, install the
original part and perform the diagnostic procedure
again.
NOTE: The left-hand drive is shown, the right-hand
drive is similar.
1. Disconnect the battery ground cable (14301) and
wait at least one minute. For additional
information, refer to Section 414-01.
WARNING: To reduce the risk of serious
personal injury, read and follow all warnings,
notes, and instructions in the supplemental
6. Remove air register.
restraint system (SRS)
7. Disconnect airbag electrical connector by
deactivation/reactivation procedure.
depressing safety lock.
2. Deactivate the supplemental restraint system
(SRS). For additional information, refer to
Supplemental Restraint System (SRS)
Deactivation and Reactivation in the General
Procedures portion of this section.
3. Remove passenger side door seal and remove
instrument panel end cover.
G12363 en
501-20b-150
Occupant Restraints — Passive
501-20b-150
REMOVAL AND INSTALLATION (Continued)
10. Remove airbag module from instrument panel.
CAUTION: Do not handle the passenger
airbag module by grabbing the edges of the
deployment door.
Installation
WARNING: To reduce the risk of serious
personal injury, read and follow all warnings,
cautions and notes at the beginning of the
removal procedure.
NOTE: Make sure the negative battery cable is still
disconnected before continuing with the installation
portion of this procedure.
8. Remove
glovebox.
1. Installation is the reverse of removal.
9. Remove the 4 bolts retaining the Airbag module.
Clockspring
Special Tool(s)
Diagnostic Tool, Restraint
System (2 req’d)
418-F395 (014-R1079)
Diagnostic Tool, Restraint
System (4 req’d)
418-F403
Diagnostic Tool, Restraint
System (2 req’d)
418-F088 (105-R0012)
G12363 en
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст